Zepeng Mao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zepeng Mao has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Junhang Tang
Department of Polymer Science and Engineering, College of Materials Science and Engineering
8 shared publicationsYuqi Shi
Department of Polymer Science and Engineering, College of Materials Science and Engineering Nanjing Tech University Nanjing China
7 shared publications- Jun Zhang
Department of Polymer Science and Engineering, College of Materials Science and Engineering Nanjing Tech University Nanjing China
3 shared publications Chu Lin
Department of Polymer Science and Engineering, College of Materials Science and Engineering Nanjing Tech University Nanjing China
2 shared publicationsHan Zhang
2 shared publicationsJun Zhang
2 shared publications
Latest Publications
- 15 July 2026
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (6) , 1546-1557
Preparation and Properties of Antistatic Coatings Doped With Macromolecular and Small‐Molecular Agents
Polymethyl methacrylate (PMMA) is prone to severe electrostatic accumulation. Conventional antistatic modifications fail to balance its optical and mechanical properties. In this study, we prepared transparent antistatic coatings using an acrylic resin/isocyanate curing agent system. Two antistatic agents, a fatty alcohol ether phosphate/quaternary ammonium salt polymer composite (H1) and a quaternary ammonium salt/nonionic surfactant composite (H2), were separately added into this system to prepare the coatings. We studied how coating surface resistivity changes with antistatic agent content at three humidity levels: 40% RH, 60% RH, and 80% RH. We also ran sealed storage tests at room temperature for 1 month to check long‐term stability. Test results prove both coatings can resist static electricity. H1 performs much better overall. Its large molecular structure stops migration and precipitation. Its lowest surface resistivity hits 10 11 Ω. It barely responds to humidity, and its performance stays steady after long storage. In comparison, H2 is made of small molecules. These small molecules easily aggregate and move inside the coating. H2 is highly sensitive to humidity, and its antistatic ability drops sharply after storage. All coatings have light transmittance above 90%, 5B adhesion and 3H pencil hardness. Their surface wettability can be adjusted, and they resist abrasion well. These multifunctional coatings suit medical and aerospace applications. This research offers guidance for designing transparent antistatic materials.
- 15 July 2026
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (6) , 1546-1557
Preparation and Properties of Antistatic Coatings Doped With Macromolecular and Small‐Molecular Agents
Polymethyl methacrylate (PMMA) is prone to severe electrostatic accumulation. Conventional antistatic modifications fail to balance its optical and mechanical properties. In this study, we prepared transparent antistatic coatings using an acrylic resin/isocyanate curing agent system. Two antistatic agents, a fatty alcohol ether phosphate/quaternary ammonium salt polymer composite (H1) and a quaternary ammonium salt/nonionic surfactant composite (H2), were separately added into this system to prepare the coatings. We studied how coating surface resistivity changes with antistatic agent content at three humidity levels: 40% RH, 60% RH, and 80% RH. We also ran sealed storage tests at room temperature for 1 month to check long‐term stability. Test results prove both coatings can resist static electricity. H1 performs much better overall. Its large molecular structure stops migration and precipitation. Its lowest surface resistivity hits 10 11 Ω. It barely responds to humidity, and its performance stays steady after long storage. In comparison, H2 is made of small molecules. These small molecules easily aggregate and move inside the coating. H2 is highly sensitive to humidity, and its antistatic ability drops sharply after storage. All coatings have light transmittance above 90%, 5B adhesion and 3H pencil hardness. Their surface wettability can be adjusted, and they resist abrasion well. These multifunctional coatings suit medical and aerospace applications. This research offers guidance for designing transparent antistatic materials.
- 12 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (4) , 3048-3059
Adjacent-Bonding Interconnected Polymer Networks Enable Lightweight Glass-Imitation Materials with Ultrahigh Modulus and Transparency
- 12 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (4) , 3048-3059
Adjacent-Bonding Interconnected Polymer Networks Enable Lightweight Glass-Imitation Materials with Ultrahigh Modulus and Transparency
- 18 August 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (26) , 49942-49951
Tailoring BaTiO3 selective localization in PVDF/PMMA blends for enhanced dielectric properties and breakdown strength
- 18 August 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (26) , 49942-49951
Tailoring BaTiO3 selective localization in PVDF/PMMA blends for enhanced dielectric properties and breakdown strength
- 24 January 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (12) , 15914-15922
Flexible PVDF-based dielectric composites prepared by surface modification of BaTiO3 with fluorosilanes of varying alkane chain lengths
- 24 January 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (12) , 15914-15922
Flexible PVDF-based dielectric composites prepared by surface modification of BaTiO3 with fluorosilanes of varying alkane chain lengths
- 13 August 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (17) , 16179-16192
Fluorosilane modification on BaTiO 3 particles: A facile method to fabricate PVDF dielectric composites with desirable mechanical properties
Dielectric capacitors have attracted much attention due to their excellent power density and long service life. Its development trend is mainly towards miniaturization, lightweight, and integration. In this work, barium titanate (BaTiO 3 , BT) particles were modified by four different coupling agents and then were introduced in polyvinylidene fluoride (PVDF) matrix to prepare PVDF/BT dielectric composites. Thermodynamic, dielectric, mechanical, and rheological properties were researched. After the combination of the surface‐modified BT and PVDF, the dielectric constant ( ≈ 33) of the composites increased by 4–5 times compared to PVDF ( = 7.8), and the dielectric loss also was obviously reduced. One remarkable thing was that modification of 1H,1H,2H,2H‐perfluorooctyltriethoxysilane (F8261) could improve the mechanical properties of composites significantly, especially in toughness. For example, the impact strength of PVDF/F8261‐BT (12.8 kJ/m 2 ) was 103.1% higher than that of PVDF/KH550‐BT (6.3 kJ/m 2 ), and even 13.3% higher than that of PVDF (11.3 kJ/m 2 ). This simple preparation method is a good grafting tactic and has a positive effect on the dielectric properties and toughness of the composites. Highlights: A method for enhancing the dielectric and mechanical properties of composites. Comparing the effects of four coupling agents on the properties of composites. F8261 can significantly improve the impact toughness of PVDF/BT. PVDF/F8261‐BT with 30 vol% filler has a dielectric constant of 34.5 at 10 2 Hz.
- 13 August 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (17) , 16179-16192
Fluorosilane modification on BaTiO 3 particles: A facile method to fabricate PVDF dielectric composites with desirable mechanical properties
Dielectric capacitors have attracted much attention due to their excellent power density and long service life. Its development trend is mainly towards miniaturization, lightweight, and integration. In this work, barium titanate (BaTiO 3 , BT) particles were modified by four different coupling agents and then were introduced in polyvinylidene fluoride (PVDF) matrix to prepare PVDF/BT dielectric composites. Thermodynamic, dielectric, mechanical, and rheological properties were researched. After the combination of the surface‐modified BT and PVDF, the dielectric constant ( ≈ 33) of the composites increased by 4–5 times compared to PVDF ( = 7.8), and the dielectric loss also was obviously reduced. One remarkable thing was that modification of 1H,1H,2H,2H‐perfluorooctyltriethoxysilane (F8261) could improve the mechanical properties of composites significantly, especially in toughness. For example, the impact strength of PVDF/F8261‐BT (12.8 kJ/m 2 ) was 103.1% higher than that of PVDF/KH550‐BT (6.3 kJ/m 2 ), and even 13.3% higher than that of PVDF (11.3 kJ/m 2 ). This simple preparation method is a good grafting tactic and has a positive effect on the dielectric properties and toughness of the composites. Highlights: A method for enhancing the dielectric and mechanical properties of composites. Comparing the effects of four coupling agents on the properties of composites. F8261 can significantly improve the impact toughness of PVDF/BT. PVDF/F8261‐BT with 30 vol% filler has a dielectric constant of 34.5 at 10 2 Hz.
- 18 March 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (9) , 8065-8075
Low percolation threshold polyvinylidene fluoride/multi‐walled carbon nanotube composites: A perspective of electrical conductivity, crystalline, rheological and mechanical properties
Recently, conductive polymer‐based composites (CPC) have gained considerable interest for their outstanding processing, mechanical, electrical properties, and resistance tunability. Multi‐walled carbon nanotube (MWCNT) was introduced into polyvinylidene fluoride (PVDF) as the conductive filler via means of melt blending in this work. Effects of MWCNT on crystalline structure, thermodynamic behavior, electrical conductivity, processing and mechanical properties of PVDF/MWCNT were under investigation. By measuring the volume resistivity of PVDF/MWCNT, it was observed to have declined from 1.54 × 1012 to 3.71 × 101 Ω∙m with the MWCNT content changed from 0.7 to 1 vol%, which plummeted by 11 orders of magnitude. Therefore, it can be inferred that the percolation threshold of MWCNT lies within the range of 0.7–1 vol%. Additionally, the percolation threshold is obtained as 0.81 vol% by fitting using the percolation theory equation. Around the percolation threshold, PVDF/MWCNT composites exhibit negligible alterations in their rheological properties when contrasted with pure PVDF, yet their mechanical properties are improved. Furthermore, MWCNT does not substantially impact the crystalline structure and thermodynamic behavior of PVDF/MWCNT.Highlights: The percolation threshold of MWCNT in PVDF is 0.81 vol%. The volume resistivity of the 1 vol% MWCNT sample was only 3.71 Ω∙m. 1 vol% MWCNT exhibit favorable rheological and mechanical properties.
- 18 March 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (9) , 8065-8075
Low percolation threshold polyvinylidene fluoride/multi‐walled carbon nanotube composites: A perspective of electrical conductivity, crystalline, rheological and mechanical properties
Recently, conductive polymer‐based composites (CPC) have gained considerable interest for their outstanding processing, mechanical, electrical properties, and resistance tunability. Multi‐walled carbon nanotube (MWCNT) was introduced into polyvinylidene fluoride (PVDF) as the conductive filler via means of melt blending in this work. Effects of MWCNT on crystalline structure, thermodynamic behavior, electrical conductivity, processing and mechanical properties of PVDF/MWCNT were under investigation. By measuring the volume resistivity of PVDF/MWCNT, it was observed to have declined from 1.54 × 1012 to 3.71 × 101 Ω∙m with the MWCNT content changed from 0.7 to 1 vol%, which plummeted by 11 orders of magnitude. Therefore, it can be inferred that the percolation threshold of MWCNT lies within the range of 0.7–1 vol%. Additionally, the percolation threshold is obtained as 0.81 vol% by fitting using the percolation theory equation. Around the percolation threshold, PVDF/MWCNT composites exhibit negligible alterations in their rheological properties when contrasted with pure PVDF, yet their mechanical properties are improved. Furthermore, MWCNT does not substantially impact the crystalline structure and thermodynamic behavior of PVDF/MWCNT.Highlights: The percolation threshold of MWCNT in PVDF is 0.81 vol%. The volume resistivity of the 1 vol% MWCNT sample was only 3.71 Ω∙m. 1 vol% MWCNT exhibit favorable rheological and mechanical properties.
- 20 October 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (1) , 1059-1068
Comparation of barium titanate and multi-walled carbon nanotubes modified PVDF composites: A perspective of dielectric, crystalline, rheological and mechanical properties
- 20 October 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (1) , 1059-1068
Comparation of barium titanate and multi-walled carbon nanotubes modified PVDF composites: A perspective of dielectric, crystalline, rheological and mechanical properties