Mauro Cosme de Carvalho Goes
Research Subjects
Mauro Cosme de Carvalho Goes has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Cicero Wellington Brito Bezerra
Universidade Federal do Maranhão, São Luís, Brazil, Brazil
2 shared publications - Suzyeth Monteiro Melo
UNIVERSIDADE FEDERAL DO MARANHÃO
2 shared publications - Claudemir Gomes de Santana
Doutor em Química pela USP/ Professor do Centro Universitário Unidade de Ensino Superior Dom Bosco
1 shared publication - Francisco Fernandes da Silva da Cruz1 shared publication
- Gabrielle Pinto Soares Moura Nunes1 shared publication
- Jaciene Jesus Freitas Cardoso1 shared publication
Latest Publications
- Open Access
- 1 April 2025
- Published by Universidade Federal de Santa Maria in Ciência e Natura
- Vol. 47, e86389
Chitosan/smectite spheres for methylene blue removal: preparation and characterization
Effluent treatment and water body decontamination are pressing global challenges due to high water consumption and industrial effluent generation. This study focused on developing efficient, cost-effective adsorbents for the removal of methylene blue, a widely used dye known for its toxicity. Chitosan (CS) and smectite clay composites were prepared and characterized using FTIR, XRD, and pHpzc analyses. FTIR confirmed the preservation of the functional groups of both materials in the prepared composite, whereas the diffractograms indicated a superficial interaction, as evidenced by the absence of shifts in the diffractogram peaks. The point of zero charge pH on the surface of the CS/Clay-180 and CS/Clay-580 composites was evaluated as 8.5 and 8.4, respectively. Adsorption experiments covered a pH range of 3 - 11, exposure times of up to 600 min and dye concentrations from 5 - 350 mg L-1. Kinetic data followed first and second-order models, while the Freundlich model best described the experimental isotherms. Our composites exhibited excellent adsorption capacities, with maximum values of 45.4 mg g-1 for CS/Clay-180 and 42.7 mg g-1 for CS/Clay-580, at pH 10 and a contact time of 300 min. Therefore, the prepared CS/clay spheres proved to be effective and environmentally friendly adsorbents for the removal of methylene blue, contributing to the development of sustainable solutions for water purification.
- 1 April 2025
- Published by Universidade Federal de Santa Maria in Ciência e Natura
- Vol. 47, e86389
Open AccessChitosan/smectite spheres for methylene blue removal: preparation and characterization
Effluent treatment and water body decontamination are pressing global challenges due to high water consumption and industrial effluent generation. This study focused on developing efficient, cost-effective adsorbents for the removal of methylene blue, a widely used dye known for its toxicity. Chitosan (CS) and smectite clay composites were prepared and characterized using FTIR, XRD, and pHpzc analyses. FTIR confirmed the preservation of the functional groups of both materials in the prepared composite, whereas the diffractograms indicated a superficial interaction, as evidenced by the absence of shifts in the diffractogram peaks. The point of zero charge pH on the surface of the CS/Clay-180 and CS/Clay-580 composites was evaluated as 8.5 and 8.4, respectively. Adsorption experiments covered a pH range of 3 - 11, exposure times of up to 600 min and dye concentrations from 5 - 350 mg L-1. Kinetic data followed first and second-order models, while the Freundlich model best described the experimental isotherms. Our composites exhibited excellent adsorption capacities, with maximum values of 45.4 mg g-1 for CS/Clay-180 and 42.7 mg g-1 for CS/Clay-580, at pH 10 and a contact time of 300 min. Therefore, the prepared CS/clay spheres proved to be effective and environmentally friendly adsorbents for the removal of methylene blue, contributing to the development of sustainable solutions for water purification.
- Open Access
- 26 October 2023
- Published by Revista Cientifica Multidisciplinar Nucleo Do Conhecimento in Revista Científica Multidisciplinar Núcleo do Conhecimento
- Vol. 02 (10) , 136-165
Simplified electrocoagulation for efficient biodiesel washing water treatment
Biodiesel is commonly purified by washing with water, but its improper disposal poses serious environmental and economic issues. Electrocoagulation (EC) is an attractive technique for treating biodiesel fuel wastewater, owing to its effectiveness, ease of operation, and low cost operation. In this study, an experimental factorial design was employed to investigated the minimum parameters required for efficient and cost-effective treatment (pH: 3 – 9; voltage: 5 – 20 V). All experiments were conducted at room temperature (25º C) using a 1 L acrylic monopolar batch reactor. Aluminum electrode (12x5x 0.1cm) were used. The effluents were characterized before and after treatments, measuring Chemical Oxygen Demand (COD), pH, color, turbidity, conductivity, Dissolved Oxygen (DO), Oil & Grease (O&G), Total Dissolved Solids (TDS), fixed solids, and volatile solids. Kinetic experiments were performed to determine the minimum operating time (30 min). The obtained results demonstrated significant removal of turbidity (94.5%), color (96.4%), COD (83.9%), conductivity (37%), and O&G (93%). Additionally, the experimental and theoretical values showed good agreement, allowing for the development of predictive mathematical models for the analytical responses.
- 26 October 2023
- Published by Revista Cientifica Multidisciplinar Nucleo Do Conhecimento in Revista Científica Multidisciplinar Núcleo do Conhecimento
- Vol. 02 (10) , 136-165
Open AccessSimplified electrocoagulation for efficient biodiesel washing water treatment
Biodiesel is commonly purified by washing with water, but its improper disposal poses serious environmental and economic issues. Electrocoagulation (EC) is an attractive technique for treating biodiesel fuel wastewater, owing to its effectiveness, ease of operation, and low cost operation. In this study, an experimental factorial design was employed to investigated the minimum parameters required for efficient and cost-effective treatment (pH: 3 – 9; voltage: 5 – 20 V). All experiments were conducted at room temperature (25º C) using a 1 L acrylic monopolar batch reactor. Aluminum electrode (12x5x 0.1cm) were used. The effluents were characterized before and after treatments, measuring Chemical Oxygen Demand (COD), pH, color, turbidity, conductivity, Dissolved Oxygen (DO), Oil & Grease (O&G), Total Dissolved Solids (TDS), fixed solids, and volatile solids. Kinetic experiments were performed to determine the minimum operating time (30 min). The obtained results demonstrated significant removal of turbidity (94.5%), color (96.4%), COD (83.9%), conductivity (37%), and O&G (93%). Additionally, the experimental and theoretical values showed good agreement, allowing for the development of predictive mathematical models for the analytical responses.