Xingpeng Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xingpeng Yu has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Yiming Zhang
College of Electrical Engineering and Automation Fuzhou University Fuzhou China
15 shared publications - Ronghuan Xie
College of Electrical Engineering and Automation Fuzhou University Fuzhou China
13 shared publications - Xiaoying Chen
College of Electrical Engineering and Automation Fuzhou University Fuzhou China
9 shared publications - Xiangpeng Cheng
School of Electrical Engineering and Automation, Fuzhou University, Fuzhou, China
8 shared publications - Yizhan Zhuang
College of Electrical Engineering and Automation Fuzhou University Fuzhou China
7 shared publications - Xingkui Mao
Fuzhou University
5 shared publications
Latest Publications
- 2 September 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Topology‐Reconfigurable Wireless Charging System for Electric Vehicles Enabling Wide‐Range and High‐Efficiency Output
With an increasing number of electric vehicles (EVs) manufacturers deploying wireless power transfer (WPT) technology, the efficiency and adaptability of such systems have garnered growing attention. To address the challenge of maintaining high efficiency over a wide battery voltage range (100–420 V) in EV wireless charging systems, this paper proposes a magnetically coupled resonant WPT system based on topology reconfiguration. The transmitter employs two identically sized unipolar coils arranged with partial overlap to achieve magnetic decoupling. By controlling the switching network at the transmitter side to switch operating modes, the proposed topology achieves high‐efficiency output across four discrete voltage modes—100, 200, 300, and 400 V—without relying on a post‐stage DC–DC converter or extreme parameter regulation. Furthermore, zero‐voltage switching (ZVS) is achieved in all four modes. A unified mathematical model of the system is established to reveal its operating mechanism, and its performance is validated using a 4.1‐kW experimental platform. Experimental results demonstrate that under perfectly aligned conditions, the system efficiencies at the respective target output voltages are 90.726%, 94.908%, 95.193%, and 95.638%. Additionally, the system was rigorously tested and verified through misalignment and variable‐load experiments. The results indicate that the system can maintain high‐efficiency operation across the entire voltage range and it achieves strong anti‐misalignment robustness and favorable constant‐voltage output performance. This verifies that the proposed topology is a highly effective approach for achieving efficient and stable wireless charging over a wide voltage range.
- 2 September 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Topology‐Reconfigurable Wireless Charging System for Electric Vehicles Enabling Wide‐Range and High‐Efficiency Output
With an increasing number of electric vehicles (EVs) manufacturers deploying wireless power transfer (WPT) technology, the efficiency and adaptability of such systems have garnered growing attention. To address the challenge of maintaining high efficiency over a wide battery voltage range (100–420 V) in EV wireless charging systems, this paper proposes a magnetically coupled resonant WPT system based on topology reconfiguration. The transmitter employs two identically sized unipolar coils arranged with partial overlap to achieve magnetic decoupling. By controlling the switching network at the transmitter side to switch operating modes, the proposed topology achieves high‐efficiency output across four discrete voltage modes—100, 200, 300, and 400 V—without relying on a post‐stage DC–DC converter or extreme parameter regulation. Furthermore, zero‐voltage switching (ZVS) is achieved in all four modes. A unified mathematical model of the system is established to reveal its operating mechanism, and its performance is validated using a 4.1‐kW experimental platform. Experimental results demonstrate that under perfectly aligned conditions, the system efficiencies at the respective target output voltages are 90.726%, 94.908%, 95.193%, and 95.638%. Additionally, the system was rigorously tested and verified through misalignment and variable‐load experiments. The results indicate that the system can maintain high‐efficiency operation across the entire voltage range and it achieves strong anti‐misalignment robustness and favorable constant‐voltage output performance. This verifies that the proposed topology is a highly effective approach for achieving efficient and stable wireless charging over a wide voltage range.
- 1 September 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
An Interoperable Wireless Charging System for Orthogonal Bipolar Coils Based on Two Self‐Decoupled Transmitting Coils
With the extensive research and application of bipolar coils, resolving the compatibility issues of bipolar coils along different directions while maintaining stable output under spatial misalignment has become an urgent requirement. This article proposes an interoperable wireless power transfer (WPT) system based on a symmetrical solenoid transmitter. By optimizing the design of two sets of solenoid coils, the transmitter achieves inherent self‐decoupling, thereby eliminating the need for auxiliary decoupling coils. Furthermore, by dynamically configuring the magnetic polarities of the transmitting windings, full interoperability with bipolar coils along different directions is realized. Simultaneously, by switching the inverter operating modes, the system is compatible with both 400‐ and 800‐V battery platforms. To validate the proposed WPT system, a downscaled experimental prototype was constructed. Experimental results demonstrate that under a ± 90 mm of X‐axis misalignment, the output voltage fluctuations for the 200‐ and 400‐V conditions are merely 3.96% and 4.06%, respectively. Moreover, the system's transmission efficiency remains above 80% throughout the entire misalignment range.
- 1 September 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
An Interoperable Wireless Charging System for Orthogonal Bipolar Coils Based on Two Self‐Decoupled Transmitting Coils
With the extensive research and application of bipolar coils, resolving the compatibility issues of bipolar coils along different directions while maintaining stable output under spatial misalignment has become an urgent requirement. This article proposes an interoperable wireless power transfer (WPT) system based on a symmetrical solenoid transmitter. By optimizing the design of two sets of solenoid coils, the transmitter achieves inherent self‐decoupling, thereby eliminating the need for auxiliary decoupling coils. Furthermore, by dynamically configuring the magnetic polarities of the transmitting windings, full interoperability with bipolar coils along different directions is realized. Simultaneously, by switching the inverter operating modes, the system is compatible with both 400‐ and 800‐V battery platforms. To validate the proposed WPT system, a downscaled experimental prototype was constructed. Experimental results demonstrate that under a ± 90 mm of X‐axis misalignment, the output voltage fluctuations for the 200‐ and 400‐V conditions are merely 3.96% and 4.06%, respectively. Moreover, the system's transmission efficiency remains above 80% throughout the entire misalignment range.
- 21 August 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Secondary‐Side Modulation Strategy for Wide‐Range ZVS in Strongly Coupled Bidirectional Wireless Power Transfer Systems
Strong magnetic coupling is usually adopted to increase the power density of bidirectional wireless power transfer (BWPT) systems. However, a large coupling coefficient distorts the resonant currents and complicates zero‐voltage‐switching (ZVS) operation, especially when the load and voltage gain vary. This paper proposes a secondary‐side pulse‐width phase‐shift modulation strategy for strongly coupled series–series BWPT (SC‐SS‐BWPT) systems. The strategy combines PWM with phase‐shift control on the secondary bridge, whereas the primary bridge remains at a fixed 50% duty cycle. An S‐domain model is developed to derive the output power and the inductor currents at the switching instants. The analysis shows that the primary‐side switching current is independent of both the secondary duty cycle and the voltage gain. Therefore, primary‐side ZVS can be preserved when the dead‐time current requirement is satisfied. The secondary‐side switches can also achieve ZVS over a wide operating range. Experiments on an SC‐SS‐BWPT prototype verify bilateral ZVS under forward and reverse power transfer, different voltage gains, and different load powers, whereas the primary‐side switching current remains nearly constant. The maximum power transfer efficiency of the system reaches 97.9%.
- 21 August 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
A Secondary‐Side Modulation Strategy for Wide‐Range ZVS in Strongly Coupled Bidirectional Wireless Power Transfer Systems
Strong magnetic coupling is usually adopted to increase the power density of bidirectional wireless power transfer (BWPT) systems. However, a large coupling coefficient distorts the resonant currents and complicates zero‐voltage‐switching (ZVS) operation, especially when the load and voltage gain vary. This paper proposes a secondary‐side pulse‐width phase‐shift modulation strategy for strongly coupled series–series BWPT (SC‐SS‐BWPT) systems. The strategy combines PWM with phase‐shift control on the secondary bridge, whereas the primary bridge remains at a fixed 50% duty cycle. An S‐domain model is developed to derive the output power and the inductor currents at the switching instants. The analysis shows that the primary‐side switching current is independent of both the secondary duty cycle and the voltage gain. Therefore, primary‐side ZVS can be preserved when the dead‐time current requirement is satisfied. The secondary‐side switches can also achieve ZVS over a wide operating range. Experiments on an SC‐SS‐BWPT prototype verify bilateral ZVS under forward and reverse power transfer, different voltage gains, and different load powers, whereas the primary‐side switching current remains nearly constant. The maximum power transfer efficiency of the system reaches 97.9%.
- 29 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-9
Free-Position Wireless Power Transfer System for Lightweight Unmanned Aerial Vehicle Based on Multireceiver-Coil Design
Uncrewed aerial vehicles (UAVs) have integrated into a variety of fields. To increase the operational longevity and load capacity limited by the battery capacity, mid-course wireless power transfer (WPT) for recharging is applied. However, the stability of the output is destabilized by the significantly variation in the mutual inductance resulting from the misalignment of coils. A free-position WPT system for lightweight UAV based on multireceiver-coil design is proposed in this letter. Three sets of receiver (Rx) coils are designed to receive flux in horizontal and vertical directions. The Rx coils are assigned to two rectifiers connected in series on the DC side so that the equivalent mutual inductance is the positive summation of all the mutual inductances. In this way, the output is maintained stable when misalignment occurs. An experimental prototype is established to verify the proposed WPT system. The results have revealed that the output voltage fluctuation is only 8.15% within the circular area of 120 mm radius, with any horizontal and rotational misalignment.
- 29 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-9
Free-Position Wireless Power Transfer System for Lightweight Unmanned Aerial Vehicle Based on Multireceiver-Coil Design
Uncrewed aerial vehicles (UAVs) have integrated into a variety of fields. To increase the operational longevity and load capacity limited by the battery capacity, mid-course wireless power transfer (WPT) for recharging is applied. However, the stability of the output is destabilized by the significantly variation in the mutual inductance resulting from the misalignment of coils. A free-position WPT system for lightweight UAV based on multireceiver-coil design is proposed in this letter. Three sets of receiver (Rx) coils are designed to receive flux in horizontal and vertical directions. The Rx coils are assigned to two rectifiers connected in series on the DC side so that the equivalent mutual inductance is the positive summation of all the mutual inductances. In this way, the output is maintained stable when misalignment occurs. An experimental prototype is established to verify the proposed WPT system. The results have revealed that the output voltage fluctuation is only 8.15% within the circular area of 120 mm radius, with any horizontal and rotational misalignment.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 4799-4808
A WPT System of Electric Vehicle With Symmetrical Anti-Offset Characteristics and Compatible With High-Voltage and Low-Voltage Charging Methods
To improve the performance and charging rate, electric vehicles (EVs) are rapidly evolving to an 800-V architecture, but the construction cost of high-voltage charging piles is high, and the mainstream is still 400-V piles. How to realize the compatibility of high-voltage architecture vehicles with existing low-voltage charging piles has become a key problem to be solved urgently. In addition, it is also necessary to consider the problem of achieving a stable output in the case of misalignment. A reconfigurable wireless charging system is proposed in this article. By combining the coupling structure with the reconfigurable series (S) compensation network, different receiving (Rx) coils are switched by switches to provide different battery voltages. In addition, another set of Rx coils is used to compensate for the decreased mutual inductance during misalignment. To verify the proposed wireless power transfer (WPT) system, a scaled-down 1.5-kW experimental prototype was built. The results show that the highest DC–DC efficiency of the system is 92.27% and 94.06% at the voltage level of 200 and 400 V, respectively. Also, it has good misalignment tolerance in two vertical symmetry directions.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (3) , 4799-4808
A WPT System of Electric Vehicle With Symmetrical Anti-Offset Characteristics and Compatible With High-Voltage and Low-Voltage Charging Methods
To improve the performance and charging rate, electric vehicles (EVs) are rapidly evolving to an 800-V architecture, but the construction cost of high-voltage charging piles is high, and the mainstream is still 400-V piles. How to realize the compatibility of high-voltage architecture vehicles with existing low-voltage charging piles has become a key problem to be solved urgently. In addition, it is also necessary to consider the problem of achieving a stable output in the case of misalignment. A reconfigurable wireless charging system is proposed in this article. By combining the coupling structure with the reconfigurable series (S) compensation network, different receiving (Rx) coils are switched by switches to provide different battery voltages. In addition, another set of Rx coils is used to compensate for the decreased mutual inductance during misalignment. To verify the proposed wireless power transfer (WPT) system, a scaled-down 1.5-kW experimental prototype was built. The results show that the highest DC–DC efficiency of the system is 92.27% and 94.06% at the voltage level of 200 and 400 V, respectively. Also, it has good misalignment tolerance in two vertical symmetry directions.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 9529-9533
Series Resonant Networks Based Hybrid Current Balancing Method for Multiphase Wireless Power Transfer
High-power wireless power transfer (WPT) systems typically adopt parallel multiphase inverters to reduce device stress. However, variations in device parameters, layout, and driving circuits often lead to unbalanced output currents among phases, resulting in circulating currents that disrupt system operation. This letter proposes a hybrid current balancing method based on series resonant networks (SRNs). The SRNs are inserted between the output nodes of each inverter and the common parallel connection point. Their resonant frequencies are designed as even multiples of the operating frequency while simultaneously resonating with the transmitting coil at the operating frequency. The introduction of SRNs does not affect the common mode output characteristics of the WPT system but introduces mixed capacitive and inductive impedance in the differential mode (DM) loop. This configuration enables a wideband high DM impedance, resulting in effective current balancing. The proposed method is validated using a three-phase WPT experimental prototype with series-series compensation, achieving a current deviation rate of only 1.39%.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (6) , 9529-9533
Series Resonant Networks Based Hybrid Current Balancing Method for Multiphase Wireless Power Transfer
High-power wireless power transfer (WPT) systems typically adopt parallel multiphase inverters to reduce device stress. However, variations in device parameters, layout, and driving circuits often lead to unbalanced output currents among phases, resulting in circulating currents that disrupt system operation. This letter proposes a hybrid current balancing method based on series resonant networks (SRNs). The SRNs are inserted between the output nodes of each inverter and the common parallel connection point. Their resonant frequencies are designed as even multiples of the operating frequency while simultaneously resonating with the transmitting coil at the operating frequency. The introduction of SRNs does not affect the common mode output characteristics of the WPT system but introduces mixed capacitive and inductive impedance in the differential mode (DM) loop. This configuration enables a wideband high DM impedance, resulting in effective current balancing. The proposed method is validated using a three-phase WPT experimental prototype with series-series compensation, achieving a current deviation rate of only 1.39%.
- Open Access
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 215980-215993
Design and Implementation of a Hybrid Wireless Charging System for Light and Heavy-Duty Electric Vehicles Based on Matrix Charging Network
Vehicles can be categorized into two types: light-duty (LD) and heavy-duty (HD) vehicles. In certain charging scenarios, it is necessary to provide wireless charging for multiple electric vehicles (EVs) of both light and heavy types. Wireless power transfer (WPT) technology for EVs offers advantages such as convenience, safety, and flexibility, making it increasingly widely adopted for various LD and HD EVs. This paper proposes a matrix-based charging system for multi-vehicle wireless charging, capable of independently charging different configurations while simultaneously powering multiple EVs. The system employs a three-switch three-bridge-arm inverter structure to establish different charging ports on the transmitter side. The working modes of the system are analyzed. The effectiveness of the proposed matrix network in the multi-vehicle wireless charging system is validated through an experimental prototype.
- 22 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 215980-215993
Open AccessDesign and Implementation of a Hybrid Wireless Charging System for Light and Heavy-Duty Electric Vehicles Based on Matrix Charging Network
Vehicles can be categorized into two types: light-duty (LD) and heavy-duty (HD) vehicles. In certain charging scenarios, it is necessary to provide wireless charging for multiple electric vehicles (EVs) of both light and heavy types. Wireless power transfer (WPT) technology for EVs offers advantages such as convenience, safety, and flexibility, making it increasingly widely adopted for various LD and HD EVs. This paper proposes a matrix-based charging system for multi-vehicle wireless charging, capable of independently charging different configurations while simultaneously powering multiple EVs. The system employs a three-switch three-bridge-arm inverter structure to establish different charging ports on the transmitter side. The working modes of the system are analyzed. The effectiveness of the proposed matrix network in the multi-vehicle wireless charging system is validated through an experimental prototype.