Robert Chehab
Robert Chehab has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Iryna Chaikovska
Institut National de Physique Nucléaire et de Physique des Particules
6 shared publications - Fahad Alharthi
Institut National de Physique Nucléaire et de Physique des Particules
5 shared publications - Laura Bandiera
INFN, Sezione di Ferrara
3 shared publications - Mattia Soldani
INFN Laboratori Nazionali di Frascati, Frascati, Italy
3 shared publications - Riccardo Negrello
INFN, Sezione di Ferrara e Dipartimento di Fisica e Scienze della Terra dell’Università
3 shared publications - Viktor Mytrochenko
Institut National de Physique Nucléaire et de Physique des Particules
3 shared publications
Latest Publications
- Open Access
- 4 November 2025
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 28 (11)
Modeling of the positron sources: Experiment-based benchmarking using SuperKEKB
High-intensity positron sources are critical for next-generation electron-positron colliders, where positron beam quality and characteristics directly impact the luminosity. Accurate modeling and validated simulation tools for positron sources are essential to optimize their performance. However, modeling a positron source tends to be complex, as it involves multiple interdependent stages, from positron production and capture dynamics to beam transport through the injector linac to the collider ring. In this work, we present a start-to-end simulation tool developed for positron sources modeling. The model was benchmarked against existing simulation tools and validated through experimental measurements conducted at the SuperKEKB positron source. Key operational parameters were systematically scanned to evaluate the simulation model performance, including the primary electron impact position on the target, solenoid field strength around the capture linac, and rf phase settings. The primary figure-of-merit for all validation tests was the positron yield at the end of the SuperKEKB positron capture section. Our model reproduces the measured positron yield ( 0.603 ± 0.003 ) under nominal operating conditions, with the simulation result of 0.603 lying well within the 0.5% statistical uncertainty. Furthermore, the simulation results demonstrate a very good agreement with experimental data and other simulation tools, confirming the model’s reliability and establishing a framework for future positron source studies.
- 4 November 2025
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 28 (11)
Open AccessModeling of the positron sources: Experiment-based benchmarking using SuperKEKB
High-intensity positron sources are critical for next-generation electron-positron colliders, where positron beam quality and characteristics directly impact the luminosity. Accurate modeling and validated simulation tools for positron sources are essential to optimize their performance. However, modeling a positron source tends to be complex, as it involves multiple interdependent stages, from positron production and capture dynamics to beam transport through the injector linac to the collider ring. In this work, we present a start-to-end simulation tool developed for positron sources modeling. The model was benchmarked against existing simulation tools and validated through experimental measurements conducted at the SuperKEKB positron source. Key operational parameters were systematically scanned to evaluate the simulation model performance, including the primary electron impact position on the target, solenoid field strength around the capture linac, and rf phase settings. The primary figure-of-merit for all validation tests was the positron yield at the end of the SuperKEKB positron capture section. Our model reproduces the measured positron yield ( 0.603 ± 0.003 ) under nominal operating conditions, with the simulation result of 0.603 lying well within the 0.5% statistical uncertainty. Furthermore, the simulation results demonstrate a very good agreement with experimental data and other simulation tools, confirming the model’s reliability and establishing a framework for future positron source studies.
- Open Access
- 15 March 2025
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1075
FCC-ee positron source from conventional to crystal-based
- 15 March 2025
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1075
Open AccessFCC-ee positron source from conventional to crystal-based
- Open Access
- 1 March 2025
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1075
Coherent radiation in axially oriented industrial-grade tungsten crystals: A viable path for an innovative -rays and positron sources- 1 March 2025
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1075
Open AccessCoherent radiation in axially oriented industrial-grade tungsten crystals: A viable path for an innovative -rays and positron sources - Open Access
Positron driven muon source for a muon collider
The design of a future multi-TeV muon collider needs new ideas to overcome the technological challenges related to muon production, cooling, accumulation and acceleration. In this paper a layout of a positron driven muon source known as the Low EMittance Muon Accelerator (LEMMA) concept is presented. The positron beam, stored in a ring with high energy acceptance and low emittance, is extracted and driven to a multi-target system, to produce muon pairs at threshold. This solution alleviates the issues related to the power deposited and the integrated Peak Energy Density Deposition (PEDD) on the targets. Muons produced in the multi-target system will then be accumulated before acceleration and injection in the collider. A multi-target line lattice has been designed to cope with the focusing of both the positron and muon beams. Studies on the number, material and thickness of the targets have been carried out. A general layout of the overall scheme and a description is presented, as well as plans for future R&D.
Open AccessPositron driven muon source for a muon collider
The design of a future multi-TeV muon collider needs new ideas to overcome the technological challenges related to muon production, cooling, accumulation and acceleration. In this paper a layout of a positron driven muon source known as the Low EMittance Muon Accelerator (LEMMA) concept is presented. The positron beam, stored in a ring with high energy acceptance and low emittance, is extracted and driven to a multi-target system, to produce muon pairs at threshold. This solution alleviates the issues related to the power deposited and the integrated Peak Energy Density Deposition (PEDD) on the targets. Muons produced in the multi-target system will then be accumulated before acceleration and injection in the collider. A multi-target line lattice has been designed to cope with the focusing of both the positron and muon beams. Studies on the number, material and thickness of the targets have been carried out. A general layout of the overall scheme and a description is presented, as well as plans for future R&D.
- Open Access
- 1 January 2014
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 319, 17-23
Development of an intense positron source using a crystal-amorphous hybrid target for linear colliders
- 1 January 2014
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 319, 17-23
Open AccessDevelopment of an intense positron source using a crystal-amorphous hybrid target for linear colliders