BYBisrat Yoseph

Bisrat Yoseph

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bisrat Yoseph has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Adaptive model predictive control for robust lateral motion tracking of semi-autonomous vehicles with dynamic parameter variation

    by Kumlachew Yeneneh, Bisrat Yoseph, Gadisa Sufe

    This study presents a novel adaptive model predictive control (AMPC) framework for robust lateral motion tracking in semi-autonomous vehicles operating under dynamically uncertain conditions. Traditional controllers often struggle to maintain stability and accuracy in the presence of nonlinear vehicle dynamics, time-varying parameters, and external disturbances. The proposed AMPC system integrates real-time parameter estimation via recursive least squares with a predictive optimization structure, allowing continuous adaptation to variations in vehicle mass, speed, and tire-road friction. A comprehensive simulation environment developed in MATLAB/Simulink was used to evaluate the AMPC across multiple scenarios, including aggressive lane changes, crosswind disturbances, and low-friction conditions (friction coefficient μ = 0.4). Quantitative comparisons with conventional model predictive control (MPC) and linear quadratic regulator (LQR) controllers demonstrate that AMPC achieves a 43% reduction in lateral tracking error and a 37% improvement in yaw angle root mean square error (RMSE), maintaining peak yaw errors below 0.275 radians even under severe disturbances. Steering control signals remain smooth and within actuator limits, with maximum steering rates under 0.48 rad/s. Additionally, a human-in-the-loop simulation confirmed the controller’s ability to handle delayed driver intervention (1–3 s) without compromising vehicle stability or trajectory tracking. These results validate AMPC’s superior robustness, adaptability, and real-time performance in managing complex lateral control tasks. The framework provides a scalable solution for enhancing safety and reliability in shared-control driving environments, addressing both technical and human-centric aspects of advanced driver assistance systems (ADAS).


  • Open Access

    Analysis of the Rollover Stability of Four‐Wheeled Vehicles on Curved and Banked Roads

    by Yalemzewd Ytayew Shiferaw, Bisrat Yoseph Gebereyesus, Velmurugan Paramasivam

    A trustworthy index that accurately displays real‐time rollover danger during vehicle maneuvers in order to design a rollover prevention system is critical to have. In this present work, the rollover of four‐wheeled vehicles on banked curves is investigated. The mathematical model is the vehicle’s rollover index on a banked curve, which is based on the lateral load transfer ratio (LTR) principle. The LTR takes the track width, location of the center of gravity, and vehicle mass as major vehicle parameters and also longitudinal velocity, lateral acceleration, road radius, steering angle, and bank angle as major state variables. The sensitivity analysis showed rollover is more sensitive to track width with a sensitivity coefficient of 1 and then to forward velocity with a sensitivity coefficient of 0.89. Distance between CGs, lateral acceleration, turning radius, and distance of CG from roll center have also a sensitivity coefficient of 0.81, 0.7, 0.69, and 0.63, respectively.


  • Open Access

    Analysis of Lateral Dynamics of the Semi- Autonomous Vehicles for Lane Changes and Cornering Maneuvers

    by Kumlachew Yeneneh, Bisrat Yoseph

    This paper investigates the challenge of maneuvering the safety and stability of semi-autonomous vehicles (SAVs) while tracking major aspects of their lateral dynamics under unpredictable situations and conditions. The common aspects of all these cases have been the necessity for balancing that model simplicity with the ability to be able to reflect the real system by using a simple geometric bicycle model, a realistic bicycle model taking into consideration forces, and state-space representation designed with capacity in mind to handle nonlinearities and disturbances. These are used in control strategies to safer and smother maneuvers. We evaluate how well SAVs maintain safety under various conditions based on lateral deviation, relative yaw angle (heading error), and steering wheel angle. The Model Predictive Control (MPC) maintains adaptability during changes, not only in terms of vehicle mass but also velocity, by the use of a cost function that governs smooth maneuvering with minimum deviation (convergence to zero). As an additional observation, at non-nominal velocities, the heavier ones may present a bigger recovery, whereas the lighter vehicles recover faster. The cost function used in MPC for the model will handle these variations so that once, stability and ride comfort can be predicted for different masses of vehicles and their respective speeds.

  • Open Access

    Response Analysis of an Experimental Study on the Effect of Speed and Premixed Fuel Ratio on Performance and Emissions in RCCI Engine

    by Habtamu Deresso Disassa, Venkata Ramayya Ancha, Ramesh Babu Nallamothu, Bisrat Yoseph, Getachew Alemayehu

    Even though CI engines are more efficient than SI engines due to their ability to operate at a greater compression ratio, a leaner charge, and lower throttle losses, they have higher PM and nitrogen oxide emissions. The induction system modification with fuel port injection is used as a parameter in RCCI engine operations for controlling emission through in‐cylinder charge reactivity and combustion phasing. By varying the amount of hydrous bioethanol in the premixed fuel injection ratio, the engine’s performance and emissions are greatly affected. In this study, an experimental investigation of a triple‐fuel RCCI engine running on port‐injected gasoline‐bioethanol blend and direct‐injected diesel fuel was conducted. Taguchi’s experimental design method was employed to assess the impact of various independent variables utilizing three set levels and two factors with the L9 orthogonal array. From the findings, the delta value shows the highest average response for each factor. Engine speed has the largest effect on the signal‐to‐noise ratio (SNR) with the (delta value of: 10.7446, rank = 1), and the delta value of 38.96, rank = 1, has the largest effect on the response of means at engine speeds of 3000 rpm. The premixed fuel ratio of G25BE75 (delta: 87.30, rank = 1) has the largest effect on the standard deviation. The lines are not parallel in all emission and performance cases except for Tb and CO2, which are close to parallel. The best means in engine speed and premixed blended fuel ratio were NOx, CO, HC, and brake power. At 3000 rpm, the speed had the larger main effect plots of SNR. The premixed fuel ratio of G25BE75 had higher main effect plots for means and standard deviations. The residues appear to have been dispersed normally based on a straight line by using a normal probability plot. The data are normally distributed, as demonstrated by the normal probability plot, and the factors had an impact on the response. Conferring to the experiment result, a high engine speed and higher ethanol content in the RCCI premixed fuel are preferred for reducing nitrogen oxides (NOx) and carbon dioxide (CO2), while unburned hydrocarbons (UHCs) and carbon monoxide (CO) showed a slight increase.


  • Open Access

    Assessment of an Electric Vehicle Drive Cycle in Relation to Minimised Energy Consumption with Driving Behaviour: The Case of Addis Ababa, Ethiopia, and Its Suburbs

    by Tatek Mamo, Girma Gebresenbet, Rajendiran Gopal, Bisrat Yoseph

    Battery electric vehicles (BEV) are suitable alternatives for achieving energy independence and meeting the criteria for reducing greenhouse emissions in the transportation sector. Evaluating their performance and energy consumption in the real-data driving cycle (DC) is important. The purpose of this work is to develop a BEV DC for the interlinked urban and suburban route of Addis Ababa (AA) in Ethiopia. In this study, a new approach of micro-trip random selection-to-rebuild with behaviour split (RSBS) was implemented, and its effectiveness was compared via the k-means clustering method. When comparing the statistical distribution of velocity and acceleration with measured real data, the RSBS cycle shows a minimum error of 2% and 2.3%, respectively. By splitting driving behaviour, aggressive drivers were found to consume more energy because of frequent panic stops and subsequent acceleration. In braking mode, coast drivers were found to improve the regenerative braking possibility and efficiency, which can extend the range by 10.8%, whereas aggressive drivers could only achieve 3.9%. Also, resynthesised RSBS with the percentage of behaviour split and its energy and power consumption were compared with standard cycles. A significant reduction of 14.57% from UDDS and 8.9% from WLTC-2 in energy consumption was achieved for the AA and its suburbs DC, indicating that this DC could be useful for both the city and suburbs.