Aliaksey A. Kapanski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aliaksey A. Kapanski has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Nadezeya V. Hruntovich
Department of Power Supply, Sukhoi State Technical University of Gomel, 246746 Gomel, Belarus
5 shared publications - Roman Vladimirovich Klyuev
Moscow Polytechnic University, Moscow, Russian Federation
5 shared publications - Aleksandr E. Boltrushevich
Department of Information Technology, Tomsk Polytechnic University, 634050 Tomsk, Russia
3 shared publications - Anton Y. Demin
Department of Information Technology, Tomsk Polytechnic University, 634050 Tomsk, Russia
3 shared publications - Nikita Vladimirovich Martyushev
Department of Information Technology, Tomsk Polytechnic University, 634050 Tomsk, Russia
3 shared publications - Svetlana N. Sorokova
Department of Mechanical Engineering, Tomsk Polytechnic University, 634050 Tomsk, Russia
3 shared publications
Latest Publications
- Open Access
Assessing the Potential for Intra-Day Load Redistribution in Water Intake Systems Under Different Electricity Tariff Models: A Comparative Case Study of Belarus and China
This article assesses the potential for intra-day redistribution of the electrical load of water intake systems under different electricity tariff models, using water supply systems in Belarus and China as case studies. It demonstrates how tariff policy influences the electrical load profile of a water intake system and quantitatively evaluates the economic effect of optimizing the operating modes of pumping equipment. The analysis is based on daily profiles of electric power and water supply. For the Belarusian water supply system, data for 2019 were considered, corresponding to the baseline operating mode without targeted load management, and data for 2023 were considered after the transition to dispatch-based control of well activation with account taken of tariff constraints (without automation tools). For the Chinese water intake system, hourly data for 2025 were used. The load redistribution potential was assessed on the basis of lagged correlation between power and water supply profiles. In addition, the F-index was applied as an aggregated diagnostic indicator intended for the comparative assessment of potential load transferability across technological stages, taking into account their share in total energy consumption. For the Chinese case, it was shown that the maximum correlation between water supply and electricity consumption across all technological stages is achieved near zero lag, which indicates a high adaptation of system operating modes to current demand; at the same time, the R values were 0.19 for reservoir intake, 0.86 for water treatment, and 0.51 for the pumping station. In the Belarusian case, for the first-lift stage, the maximum correlation is shifted by −6 h relative to zero lag, indicating a less rigid linkage of pump operation to current demand and a more inertial response of the system. A comparison of 2019 and 2023 for the Belarusian facility showed that targeted regulation of well activation and load redistribution across tariff zones reduced the total electricity cost by 1.58%, confirming the potential for further optimization of electricity consumption regimes.
Open AccessAssessing the Potential for Intra-Day Load Redistribution in Water Intake Systems Under Different Electricity Tariff Models: A Comparative Case Study of Belarus and China
This article assesses the potential for intra-day redistribution of the electrical load of water intake systems under different electricity tariff models, using water supply systems in Belarus and China as case studies. It demonstrates how tariff policy influences the electrical load profile of a water intake system and quantitatively evaluates the economic effect of optimizing the operating modes of pumping equipment. The analysis is based on daily profiles of electric power and water supply. For the Belarusian water supply system, data for 2019 were considered, corresponding to the baseline operating mode without targeted load management, and data for 2023 were considered after the transition to dispatch-based control of well activation with account taken of tariff constraints (without automation tools). For the Chinese water intake system, hourly data for 2025 were used. The load redistribution potential was assessed on the basis of lagged correlation between power and water supply profiles. In addition, the F-index was applied as an aggregated diagnostic indicator intended for the comparative assessment of potential load transferability across technological stages, taking into account their share in total energy consumption. For the Chinese case, it was shown that the maximum correlation between water supply and electricity consumption across all technological stages is achieved near zero lag, which indicates a high adaptation of system operating modes to current demand; at the same time, the R values were 0.19 for reservoir intake, 0.86 for water treatment, and 0.51 for the pumping station. In the Belarusian case, for the first-lift stage, the maximum correlation is shifted by −6 h relative to zero lag, indicating a less rigid linkage of pump operation to current demand and a more inertial response of the system. A comparison of 2019 and 2023 for the Belarusian facility showed that targeted regulation of well activation and load redistribution across tariff zones reduced the total electricity cost by 1.58%, confirming the potential for further optimization of electricity consumption regimes.
- Open Access
- 3 October 2025
- Published by MDPI AG in Technologies
- Vol. 13 (10) , 449
Temporal Segmentation of Urban Water Consumption Patterns Based on Non-Parametric Density Clustering
The management of modern water supply systems requires a detailed analysis of consumption patterns in order to optimize pump operation schedules, reduce energy costs, and support the development of intelligent management systems. Traditional clustering algorithms are applied for these tasks; however, their limitation lies in the need to predefine the number of clusters. The aim of this study was to develop and validate a non-parametric method for clustering daily water consumption profiles based on a modified DBSCAN algorithm. The proposed approach includes the automatic optimization of neighborhood radius and the minimum number of points required to form a cluster. The input data consisted of half-hourly water supply and electricity consumption values for the water supply system of Gomel (Republic of Belarus), supplemented with the time-of-day factor. As a result of the multidimensional clustering, two stable regimes were identified: a high-demand regime (6:30–22:30), covering about 46% of the data and accounting for more than half of the total water supply and electricity consumption, and a low-demand regime (0:30–6:00), representing about 21% of the data and forming around 15% of the resources. The remaining regimes reflect transitional states in morning and evening periods. The obtained results make it possible to define the temporal boundaries of the regimes and to use them for data labeling in the development of predictive water consumption models.
- 3 October 2025
- Published by MDPI AG in Technologies
- Vol. 13 (10) , 449
Open AccessTemporal Segmentation of Urban Water Consumption Patterns Based on Non-Parametric Density Clustering
The management of modern water supply systems requires a detailed analysis of consumption patterns in order to optimize pump operation schedules, reduce energy costs, and support the development of intelligent management systems. Traditional clustering algorithms are applied for these tasks; however, their limitation lies in the need to predefine the number of clusters. The aim of this study was to develop and validate a non-parametric method for clustering daily water consumption profiles based on a modified DBSCAN algorithm. The proposed approach includes the automatic optimization of neighborhood radius and the minimum number of points required to form a cluster. The input data consisted of half-hourly water supply and electricity consumption values for the water supply system of Gomel (Republic of Belarus), supplemented with the time-of-day factor. As a result of the multidimensional clustering, two stable regimes were identified: a high-demand regime (6:30–22:30), covering about 46% of the data and accounting for more than half of the total water supply and electricity consumption, and a low-demand regime (0:30–6:00), representing about 21% of the data and forming around 15% of the resources. The remaining regimes reflect transitional states in morning and evening periods. The obtained results make it possible to define the temporal boundaries of the regimes and to use them for data labeling in the development of predictive water consumption models.
- Open Access
- 1 September 2025
- Published by Belarusian National Technical University in Science & Technique
- Vol. 24 (4) , 327-328
Multi-Level Strategy for Placement of Measuring Devices in Engineering Systems with Distributed Loads Based on Hierarchical and Cluster Analysis
Building a digital model of a “smart city” in the context of rapid development of technical infrastructure requires effective methods for monitoring and managing engineering systems. One of the key tasks is to optimize the placement of measuring devices in systems such as water and energy supply, including gas, electricity and heat. In conditions of limited financial resources and the need to ensure high monitoring accuracy, it is important to take into account not only the geographical distribution of consumers, but also the intensity of their load. This is especially important for managing distributed technical systems, where it is necessary to minimize equipment costs, while ensuring full network coverage and timely detection of anomalies. The purpose of this study is to develop a methodology for the optimal placement of measuring devices in engineering systems that takes into account both the spatial location of consumers and their load. The paper uses a multilevel analysis strategy using Ward’s method for hierarchical clustering and the k-means algorithm. Based on the proposed methodology, four territorial clusters were identified using the example of the Gomel water supply system, on the basis of which 20 pressure sensors were distributed proportionally to the contribution of consumption. The article shows how multiparameter clustering can be used to determine optimal centers for placing measuring devices that are focused on more powerful consumers, while taking into account the geographic distribution of objects as a whole. The developed approach allows for the efficient distribution of measuring devices taking into account the actual load of objects in the system and their geographic location, which ensures the best coverage of the territory under conditions of a limited amount of equipment. The approach presented in the article can be adapted for various technical systems, ensuring universality and flexibility of application.
- 1 September 2025
- Published by Belarusian National Technical University in Science & Technique
- Vol. 24 (4) , 327-328
Open AccessMulti-Level Strategy for Placement of Measuring Devices in Engineering Systems with Distributed Loads Based on Hierarchical and Cluster Analysis
Building a digital model of a “smart city” in the context of rapid development of technical infrastructure requires effective methods for monitoring and managing engineering systems. One of the key tasks is to optimize the placement of measuring devices in systems such as water and energy supply, including gas, electricity and heat. In conditions of limited financial resources and the need to ensure high monitoring accuracy, it is important to take into account not only the geographical distribution of consumers, but also the intensity of their load. This is especially important for managing distributed technical systems, where it is necessary to minimize equipment costs, while ensuring full network coverage and timely detection of anomalies. The purpose of this study is to develop a methodology for the optimal placement of measuring devices in engineering systems that takes into account both the spatial location of consumers and their load. The paper uses a multilevel analysis strategy using Ward’s method for hierarchical clustering and the k-means algorithm. Based on the proposed methodology, four territorial clusters were identified using the example of the Gomel water supply system, on the basis of which 20 pressure sensors were distributed proportionally to the contribution of consumption. The article shows how multiparameter clustering can be used to determine optimal centers for placing measuring devices that are focused on more powerful consumers, while taking into account the geographic distribution of objects as a whole. The developed approach allows for the efficient distribution of measuring devices taking into account the actual load of objects in the system and their geographic location, which ensures the best coverage of the territory under conditions of a limited amount of equipment. The approach presented in the article can be adapted for various technical systems, ensuring universality and flexibility of application.
- Open Access
- 22 July 2025
- Published by Kazan State Power Engineering University in Power engineering: research, equipment, technology
- Vol. 27 (3) , 23-37
Classification of consumers and analysis of electricity consumption patterns based on variance analysis methods
Relevance. The increasing electricity consumption in the private residential sector, driven in part by the growing use of electric heating, is leading to higher loads on 0.4 kV power transmission lines. Traditional standardized load profiles do not always reflect modern consumption patterns and conditions, which creates risks of inaccurate assessments of the electrical grid’s capacity and necessitates more precise modeling of grid operating conditions.Purpose. To develop approaches for classifying consumers and identifying statistically significant patterns in electricity consumption in private residential areas for subsequent calculation of grid operating conditions.Methods. The analysis was based on half-hourly electricity consumption data from 42 private houses, collected via an Automated Meter Reading and Management System (AMRMS). The data was cleaned using the three-sigma rule to remove gaps and outliers, and heat maps were used to identify non-representative consumers. The statistical significance of differences was determined using analysis of variance (ANOVA) and Tukey’s test. Based on median consumption values, consumer groups were formed (low and high electricity consumption). Data processing and visualization were performed using MS Excel, Python (Pandas, NumPy, SciPy libraries), and the Statistica software package.Results. The analysis confirmed statistically significant differences in electricity consumption between most of the houses (F = 2065.4, p < 0.001). Tukey’s test showed that within each group, homes exhibited relatively stable energy consumption values, while intergroup comparisons revealed substantial variations in electricity usage. As a result of the study, two consumer types were identified: "low" and "high" consumption groups. The high-consumption group exhibited distinct evening peaks (18:00–22:00), whereas the low-consumption group had a more evenly distributed load profile.Conclusion. The application of statistical analysis methods to electricity consumption data enabled the simplification of household classification into two main groups and the development of typical consumption profiles. These results were integrated into the LineCapacity software, facilitating grid operation calculations and reducing the risk of misjudging the available power transmission capacity. A promising research direction is planned, focusing on expanding the dataset on residential electricity consumption. This will allow for the consideration of seasonal factors and the development of simulation modeling mechanisms for various consumer groups.
- 22 July 2025
- Published by Kazan State Power Engineering University in Power engineering: research, equipment, technology
- Vol. 27 (3) , 23-37
Open AccessClassification of consumers and analysis of electricity consumption patterns based on variance analysis methods
Relevance. The increasing electricity consumption in the private residential sector, driven in part by the growing use of electric heating, is leading to higher loads on 0.4 kV power transmission lines. Traditional standardized load profiles do not always reflect modern consumption patterns and conditions, which creates risks of inaccurate assessments of the electrical grid’s capacity and necessitates more precise modeling of grid operating conditions.Purpose. To develop approaches for classifying consumers and identifying statistically significant patterns in electricity consumption in private residential areas for subsequent calculation of grid operating conditions.Methods. The analysis was based on half-hourly electricity consumption data from 42 private houses, collected via an Automated Meter Reading and Management System (AMRMS). The data was cleaned using the three-sigma rule to remove gaps and outliers, and heat maps were used to identify non-representative consumers. The statistical significance of differences was determined using analysis of variance (ANOVA) and Tukey’s test. Based on median consumption values, consumer groups were formed (low and high electricity consumption). Data processing and visualization were performed using MS Excel, Python (Pandas, NumPy, SciPy libraries), and the Statistica software package.Results. The analysis confirmed statistically significant differences in electricity consumption between most of the houses (F = 2065.4, p < 0.001). Tukey’s test showed that within each group, homes exhibited relatively stable energy consumption values, while intergroup comparisons revealed substantial variations in electricity usage. As a result of the study, two consumer types were identified: "low" and "high" consumption groups. The high-consumption group exhibited distinct evening peaks (18:00–22:00), whereas the low-consumption group had a more evenly distributed load profile.Conclusion. The application of statistical analysis methods to electricity consumption data enabled the simplification of household classification into two main groups and the development of typical consumption profiles. These results were integrated into the LineCapacity software, facilitating grid operation calculations and reducing the risk of misjudging the available power transmission capacity. A promising research direction is planned, focusing on expanding the dataset on residential electricity consumption. This will allow for the consideration of seasonal factors and the development of simulation modeling mechanisms for various consumer groups.
- 2 May 2025
- Published by Springer Nature in Water Conservation Science and Engineering
- Vol. 10 (2) , 1-16
Identification of Easily Accessible Urban Water Consumption Factors for Energy-Efficient Management of Pumping Stations
- 2 May 2025
- Published by Springer Nature in Water Conservation Science and Engineering
- Vol. 10 (2) , 1-16
Identification of Easily Accessible Urban Water Consumption Factors for Energy-Efficient Management of Pumping Stations
- Open Access
- 2 April 2025
- Published by MDPI AG in Smart Cities
- Vol. 8 (2) , 59
Intelligent Methods of Operational Response to Accidents in Urban Water Supply Systems Based on LSTM Neural Network Models
This paper investigates the application of recurrent neural networks, specifically Long Short-Term Memory (LSTM) models, for pressure forecasting in urban water supply systems. The objective of this study was to evaluate the effectiveness of LSTM models for pressure prediction tasks. To acquire real-time pressure data, an information system based on Internet of Things (IoT) technology using the MQTT protocol was proposed. The paper presents a data pre-processing algorithm for model training, as well as an analysis of the influence of various architectural parameters, such as the number of LSTM layers, the utilization of Dropout layers for regularization, and the number of neurons in Dense (fully connected) layers. The impact of seasonal factors, including month, day of the week, and time of day, on the pressure forecast quality was also investigated. The results obtained demonstrate that the optimal model consists of two LSTM layers, one Dropout layer, and one Dense layer. The incorporation of seasonal parameters improved prediction accuracy. The model training time increased significantly with the number of layers and neurons, but this did not always result in improved forecast accuracy. The results showed that the optimally tuned LSTM model can achieve high accuracy and outperform traditional methods such as the Holt–Winters model. This study confirms the effectiveness of using LSTM for forecasting in the water supply field and highlights the importance of pre-optimizing the model parameters to achieve the best forecasting results.
- 2 April 2025
- Published by MDPI AG in Smart Cities
- Vol. 8 (2) , 59
Open AccessIntelligent Methods of Operational Response to Accidents in Urban Water Supply Systems Based on LSTM Neural Network Models
This paper investigates the application of recurrent neural networks, specifically Long Short-Term Memory (LSTM) models, for pressure forecasting in urban water supply systems. The objective of this study was to evaluate the effectiveness of LSTM models for pressure prediction tasks. To acquire real-time pressure data, an information system based on Internet of Things (IoT) technology using the MQTT protocol was proposed. The paper presents a data pre-processing algorithm for model training, as well as an analysis of the influence of various architectural parameters, such as the number of LSTM layers, the utilization of Dropout layers for regularization, and the number of neurons in Dense (fully connected) layers. The impact of seasonal factors, including month, day of the week, and time of day, on the pressure forecast quality was also investigated. The results obtained demonstrate that the optimal model consists of two LSTM layers, one Dropout layer, and one Dense layer. The incorporation of seasonal parameters improved prediction accuracy. The model training time increased significantly with the number of layers and neurons, but this did not always result in improved forecast accuracy. The results showed that the optimally tuned LSTM model can achieve high accuracy and outperform traditional methods such as the Holt–Winters model. This study confirms the effectiveness of using LSTM for forecasting in the water supply field and highlights the importance of pre-optimizing the model parameters to achieve the best forecasting results.
- Open Access
- 21 February 2025
- Published by Belarusian National Technical University in Science & Technique
- Vol. 24 (1) , 72-82
Climatic Factors and Their Role in Energy Management and Water Consumption in the Urban Water Supply System
The article considers the influence of climatic factors on energy and water consumption of the urban water supply system. The purpose of the study is to identify the relationships between outdoor air temperature, precipitation and load on the water supply system to substantiate the factors necessary for creating seasonal models of water consumption and increаsing the energy efficiency of water intakes. The objective of the scientific work was to test the hypothesis, according to which an increase in air temperature leads to an increase in water consumption and, as a consequence, to an increase in energy costs for the operation of pumping stations and water treatment systems. At the same time, it was assumed that precipitation would have the opposite effect, reducing water consumption during periods of intense rainfall. The work used correlation analysis to assess the strength and direction of the relationships between air temperature, precipitation and energy and water consumption parameters. Regression analysis was used to quantitatively assess the impact of climatic factors. The moving average method was used to smooth the data and reduce the spread of random fluctuations. Data filtering and cutting methods were also used, which made it possible to divide them by temperature thresholds and conduct separate studies for different ranges. The obtained results demonstrate that the growth of energy consumption is closely related to the increase in water demand, which increases with each degree of outside air temperature. This is explained by the expected increase in water consumption for irrigation and household needs during warm periods. Above 25 °C, the temperature factor determined 15.8 % of water consumption, which also coincided with the growth of this contribution to the electricity consumption of the system (15.6 %). However, when analyzing data in the area of negative temperatures, no obvious relationship was observed between temperature and water demand. At the same time, a correlation was found between temperature and electricity consumption, which is associated with additional costs for maintaining the water supply system in cold climates. Conclusions are made about the need for further study of additional variables, such as types of weekdays (working days, weekends, holidays), seasons of the year, as well as other socio-economic factors affecting water consumption and energy costs. The comprehensive results of the work can be used for planning the work of water utilities, managing energy resources and developing strategies to improve energy efficiency in water supply systems.
- 21 February 2025
- Published by Belarusian National Technical University in Science & Technique
- Vol. 24 (1) , 72-82
Open AccessClimatic Factors and Their Role in Energy Management and Water Consumption in the Urban Water Supply System
The article considers the influence of climatic factors on energy and water consumption of the urban water supply system. The purpose of the study is to identify the relationships between outdoor air temperature, precipitation and load on the water supply system to substantiate the factors necessary for creating seasonal models of water consumption and increаsing the energy efficiency of water intakes. The objective of the scientific work was to test the hypothesis, according to which an increase in air temperature leads to an increase in water consumption and, as a consequence, to an increase in energy costs for the operation of pumping stations and water treatment systems. At the same time, it was assumed that precipitation would have the opposite effect, reducing water consumption during periods of intense rainfall. The work used correlation analysis to assess the strength and direction of the relationships between air temperature, precipitation and energy and water consumption parameters. Regression analysis was used to quantitatively assess the impact of climatic factors. The moving average method was used to smooth the data and reduce the spread of random fluctuations. Data filtering and cutting methods were also used, which made it possible to divide them by temperature thresholds and conduct separate studies for different ranges. The obtained results demonstrate that the growth of energy consumption is closely related to the increase in water demand, which increases with each degree of outside air temperature. This is explained by the expected increase in water consumption for irrigation and household needs during warm periods. Above 25 °C, the temperature factor determined 15.8 % of water consumption, which also coincided with the growth of this contribution to the electricity consumption of the system (15.6 %). However, when analyzing data in the area of negative temperatures, no obvious relationship was observed between temperature and water demand. At the same time, a correlation was found between temperature and electricity consumption, which is associated with additional costs for maintaining the water supply system in cold climates. Conclusions are made about the need for further study of additional variables, such as types of weekdays (working days, weekends, holidays), seasons of the year, as well as other socio-economic factors affecting water consumption and energy costs. The comprehensive results of the work can be used for planning the work of water utilities, managing energy resources and developing strategies to improve energy efficiency in water supply systems.
- Open Access
- 7 February 2025
- Published by MDPI AG in Preprints.org
Intelligent Methods of Operational Response to Accidents in Urban Water Supply Systems Based on LSTM Neural Network Models
This paper investigates the application of recurrent neural networks, specifically Long Short-Term Memory (LSTM) models, for pressure forecasting in urban water supply systems. The objective of this study was to evaluate the effectiveness of LSTM models for pressure prediction tasks. To acquire real-time pressure data, an information system based on Internet of Things (IoT) technology using the MQTT protocol was proposed. The paper presents a data preprocessing algorithm for model training, as well as an analysis of the influence of various architectural parameters, such as the number of LSTM layers, the utilization of Dropout layers for regularization, and the number of neurons in Dense (fully connected) layers. The impact of seasonal factors, including month, day of the week, and time of day, on the pressure forecast quality was also investigated. The results obtained demonstrate that the optimal model consists of two LSTM layers, one Dropout layer, and one Dense layer. The incorporation of seasonal parameters improved prediction accuracy. The model training time increased significantly with the number of layers and neurons, but this did not always result in improved forecast accuracy. The results showed that the optimally tuned LSTM model can achieve high accuracy and outperform traditional methods such as the Holt-Winters model. This study confirms the effectiveness of using LSTM for forecasting in the water supply field and highlights the importance of pre-optimizing the model parameters to achieve the best forecasting results.
- 7 February 2025
- Published by MDPI AG in Preprints.org
Open AccessIntelligent Methods of Operational Response to Accidents in Urban Water Supply Systems Based on LSTM Neural Network Models
This paper investigates the application of recurrent neural networks, specifically Long Short-Term Memory (LSTM) models, for pressure forecasting in urban water supply systems. The objective of this study was to evaluate the effectiveness of LSTM models for pressure prediction tasks. To acquire real-time pressure data, an information system based on Internet of Things (IoT) technology using the MQTT protocol was proposed. The paper presents a data preprocessing algorithm for model training, as well as an analysis of the influence of various architectural parameters, such as the number of LSTM layers, the utilization of Dropout layers for regularization, and the number of neurons in Dense (fully connected) layers. The impact of seasonal factors, including month, day of the week, and time of day, on the pressure forecast quality was also investigated. The results obtained demonstrate that the optimal model consists of two LSTM layers, one Dropout layer, and one Dense layer. The incorporation of seasonal parameters improved prediction accuracy. The model training time increased significantly with the number of layers and neurons, but this did not always result in improved forecast accuracy. The results showed that the optimally tuned LSTM model can achieve high accuracy and outperform traditional methods such as the Holt-Winters model. This study confirms the effectiveness of using LSTM for forecasting in the water supply field and highlights the importance of pre-optimizing the model parameters to achieve the best forecasting results.
- Open Access
- 21 January 2025
- Published by MDPI AG in Smart Cities
- Vol. 8 (1) , 14
Geospatial Clustering in Smart City Resource Management: An Initial Step in the Optimisation of Complex Technical Supply Systems
For large cities with developing infrastructures, optimising water supply systems plays a crucial role. However, without a clear understanding of the network structure and water consumption patterns, addressing these challenges becomes significantly more complex. This paper proposes a methodology for geospatial data analysis aimed at solving two key tasks. The first is the delineation of service zones for infrastructure objects to enhance system manageability. The second involves the development of an approach for the optimal placement of devices to collect and transmit hydraulic network parameters, ensuring their alignment with both water supply sources and serviced areas. The study focuses on data from the water supply network of a city with a population exceeding half a million people, where hierarchical clustering using Ward’s method was applied to analyse territorial distribution. Four territorial clusters were identified, each characterised by unique attributes reflecting consumer concentration and water consumption volumes. The cluster boundaries were compared with the existing service scheme of the system, confirming their alignment with real infrastructure. The quality of clustering was further evaluated using the silhouette coefficient, which validated the high accuracy and reliability of the chosen approach. The paper demonstrates the effectiveness of cluster boundary visualisation for assessing the uniform distribution of pressure sensors within the urban water supply network. The results of the study show that integrating geographic data with water consumption information not only facilitates effective infrastructure planning and resource allocation but also lays the foundation for the digitalization of the hydraulic network, a critical component of sustainable development in modern smart cities.
- 21 January 2025
- Published by MDPI AG in Smart Cities
- Vol. 8 (1) , 14
Open AccessGeospatial Clustering in Smart City Resource Management: An Initial Step in the Optimisation of Complex Technical Supply Systems
For large cities with developing infrastructures, optimising water supply systems plays a crucial role. However, without a clear understanding of the network structure and water consumption patterns, addressing these challenges becomes significantly more complex. This paper proposes a methodology for geospatial data analysis aimed at solving two key tasks. The first is the delineation of service zones for infrastructure objects to enhance system manageability. The second involves the development of an approach for the optimal placement of devices to collect and transmit hydraulic network parameters, ensuring their alignment with both water supply sources and serviced areas. The study focuses on data from the water supply network of a city with a population exceeding half a million people, where hierarchical clustering using Ward’s method was applied to analyse territorial distribution. Four territorial clusters were identified, each characterised by unique attributes reflecting consumer concentration and water consumption volumes. The cluster boundaries were compared with the existing service scheme of the system, confirming their alignment with real infrastructure. The quality of clustering was further evaluated using the silhouette coefficient, which validated the high accuracy and reliability of the chosen approach. The paper demonstrates the effectiveness of cluster boundary visualisation for assessing the uniform distribution of pressure sensors within the urban water supply network. The results of the study show that integrating geographic data with water consumption information not only facilitates effective infrastructure planning and resource allocation but also lays the foundation for the digitalization of the hydraulic network, a critical component of sustainable development in modern smart cities.
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Electrotechnical Systems and Complexes
- No. 4(65)
Socio-Economic Aspects of Energy Regimes Formation in Urban Water Supply
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Electrotechnical Systems and Complexes
- No. 4(65)
Socio-Economic Aspects of Energy Regimes Formation in Urban Water Supply