Nan Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Nan Lin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Yue Zhao
University of Arkansas
5 shared publications - Fei Diao
Power Electronic Systems Laboratory at Arkansas (PESLA), University of Arkansas, Fayetteville, AR, USA
2 shared publications - Ahmad Al-Hmoud
Department of Energy Engineering, German Jordanian University, Amman 11180, Jordan
1 shared publication - Feng Guo
Power Electronics and Smart Energy Laboratory (PESEL), Department of Electrical Engineering, University of Wisconsin-Milwaukee, 115 E Reindl Way, Glendale, WI 53212, USA
1 shared publication - Homer Alan Mantooth
University of Arkansas
1 shared publication - Hui Cao
University of Arkansas
1 shared publication
Latest Publications
- 28 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (3) , 3161-3172
Design and Demonstration of a Medium-Voltage High-Power All Silicon Carbide ANPC Converter With Optimized Busbar Architecture
In this paper, the design and optimization of a high-power active-neutral-point-clamped (ANPC) converter using 1.7 kV silicon carbide power modules and low-inductance laminated bussing architecture are presented. Various optimizations have been performed to reduce parasitic inductance along the current commutation loops (CCL), while achieving high power density and meeting insulation requirements. Due to the low inductance in the CCLs, the proposed ANPC design can support up to 2.6 kV DC link voltage. In addition, a method to improve the accuracy of voltage ringing frequency measurement during the switching transient has been proposed, which can further lead to a precise CCL stray inductance calculation that agrees well with the measurement using impedance analyzer and the Q3D based simulation. Extensive experimental studies, including switching tests and continuous power tests, have been performed to validate effectiveness of proposed methods and the converter prototyped.
- 28 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (3) , 3161-3172
Design and Demonstration of a Medium-Voltage High-Power All Silicon Carbide ANPC Converter With Optimized Busbar Architecture
In this paper, the design and optimization of a high-power active-neutral-point-clamped (ANPC) converter using 1.7 kV silicon carbide power modules and low-inductance laminated bussing architecture are presented. Various optimizations have been performed to reduce parasitic inductance along the current commutation loops (CCL), while achieving high power density and meeting insulation requirements. Due to the low inductance in the CCLs, the proposed ANPC design can support up to 2.6 kV DC link voltage. In addition, a method to improve the accuracy of voltage ringing frequency measurement during the switching transient has been proposed, which can further lead to a precise CCL stray inductance calculation that agrees well with the measurement using impedance analyzer and the Q3D based simulation. Extensive experimental studies, including switching tests and continuous power tests, have been performed to validate effectiveness of proposed methods and the converter prototyped.
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (9) , 4341-4345
An Active Gate Driver Control Scheme for Steady-State Current Balancing of Paralleled SiC MOSFETs
Silicon carbide (SiC) modules are increasingly adopted in high power applications, where paralleling multiple modules is a common practice to achieve high current carrying capability. This, however, leads to unbalanced current sharing among the paralleled modules. Active gate driver (AGD) can regulate switching behavior of MOSFETs, which has been widely studied to solve the unbalanced current issue among paralleled SiC MOSFETs. An AGD control method targeted at mitigating steady unbalanced current among paralleled SiC MOSFETs is proposed in this brief. The equivalent on-state drain-to-source resistance of paralleled MOSFETs is regulated by applying pulse width modulation (PWM) between two voltage rails in the AGD to compensate parameter mismatches causing steady-state unbalanced current. The proposed AGD can also eliminate the transient unbalanced current by manipulating the delay between the devices in parallel. Comprehensive double pulse tests were conducted to validate the effectiveness of the proposed method. Extensive loss analysis has been performed to highlight the ability of the proposed AGD to achieve evenly loss distribution among modules under different case temperatures and DC bus voltages. The proposed AGD current balancing method is straightforward to implement but was proven to effectively address the current issues among the paralleled SiC modules.
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (9) , 4341-4345
An Active Gate Driver Control Scheme for Steady-State Current Balancing of Paralleled SiC MOSFETs
Silicon carbide (SiC) modules are increasingly adopted in high power applications, where paralleling multiple modules is a common practice to achieve high current carrying capability. This, however, leads to unbalanced current sharing among the paralleled modules. Active gate driver (AGD) can regulate switching behavior of MOSFETs, which has been widely studied to solve the unbalanced current issue among paralleled SiC MOSFETs. An AGD control method targeted at mitigating steady unbalanced current among paralleled SiC MOSFETs is proposed in this brief. The equivalent on-state drain-to-source resistance of paralleled MOSFETs is regulated by applying pulse width modulation (PWM) between two voltage rails in the AGD to compensate parameter mismatches causing steady-state unbalanced current. The proposed AGD can also eliminate the transient unbalanced current by manipulating the delay between the devices in parallel. Comprehensive double pulse tests were conducted to validate the effectiveness of the proposed method. Extensive loss analysis has been performed to highlight the ability of the proposed AGD to achieve evenly loss distribution among modules under different case temperatures and DC bus voltages. The proposed AGD current balancing method is straightforward to implement but was proven to effectively address the current issues among the paralleled SiC modules.
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (2) , 639-651
Low-Latency Attack Detection With Dynamic Watermarking for Grid-Connected Photovoltaic Systems
This paper proposes an active low latency attack detection algorithm to improve the cybersecurity of grid-connected photovoltaic (PV) systems. The algorithm is developed by using a hybrid model- and data-driven approach, where the test statistics are formulated by using both the physical model of the PV farm and historical measurements. Unlike most previous detection algorithms that mainly focus on detection accuracy, the proposed algorithm aims at minimizing detection delay while ensuring detection accuracy. The low latency detection algorithm is developed by designing a generalized cumulative sum (CUSUM) detector with a dynamic watermark, which can detect cyberattacks even if the adversary has full knowledge of the system model. To evaluate the performance of the low latency detection algorithm, we propose to measure the stealthiness of cyberattacks by using the Kullback-Leibler (KL) divergence between the pre- and post-attack distributions of the test statistics. Simulation results demonstrate that the proposed algorithm can accurately detect cyberattacks with minimum delays.
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (2) , 639-651
Low-Latency Attack Detection With Dynamic Watermarking for Grid-Connected Photovoltaic Systems
This paper proposes an active low latency attack detection algorithm to improve the cybersecurity of grid-connected photovoltaic (PV) systems. The algorithm is developed by using a hybrid model- and data-driven approach, where the test statistics are formulated by using both the physical model of the PV farm and historical measurements. Unlike most previous detection algorithms that mainly focus on detection accuracy, the proposed algorithm aims at minimizing detection delay while ensuring detection accuracy. The low latency detection algorithm is developed by designing a generalized cumulative sum (CUSUM) detector with a dynamic watermark, which can detect cyberattacks even if the adversary has full knowledge of the system model. To evaluate the performance of the low latency detection algorithm, we propose to measure the stealthiness of cyberattacks by using the Kullback-Leibler (KL) divergence between the pre- and post-attack distributions of the test statistics. Simulation results demonstrate that the proposed algorithm can accurately detect cyberattacks with minimum delays.
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6986-7000
An Effective Current Balancing Method for Inverters With Paralleled Silicon Carbide Power Modules
Silicon carbide (SiC) MOSFET has many superior characteristics in high power applications. Paralleling the SiC devices is an effective approach to increase the current capacity of the system, which also leads to current sharing issues. In this paper, both transient and steady-state current sharing issues are studied for the high-power grid-tied inverters with paralleled SiC modules with an effective current balancing strategy proposed to address both issues simultaneously. The steady-state imbalance current due to the parameter mismatch is suppressed by the self-inductance of power cables used for paralleling connection. With the elimination of steady-state imbalance current, the transient imbalance current sensing is much simplified and can be realized by using low-cost current sensors. With the sensed imbalance current, a closed-loop control approach is proposed to adjust the modulation reference signal for each module to mitigate the remaining transient imbalance current. The proposed method is straightforward to implement with enhanced compatibility and flexibility compared to existing methods. Experimental studies are performed using inverters with 2 and 4 power modules paralleled in each phase to demonstrate the effectiveness of the proposed method.
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6986-7000
An Effective Current Balancing Method for Inverters With Paralleled Silicon Carbide Power Modules
Silicon carbide (SiC) MOSFET has many superior characteristics in high power applications. Paralleling the SiC devices is an effective approach to increase the current capacity of the system, which also leads to current sharing issues. In this paper, both transient and steady-state current sharing issues are studied for the high-power grid-tied inverters with paralleled SiC modules with an effective current balancing strategy proposed to address both issues simultaneously. The steady-state imbalance current due to the parameter mismatch is suppressed by the self-inductance of power cables used for paralleling connection. With the elimination of steady-state imbalance current, the transient imbalance current sensing is much simplified and can be realized by using low-cost current sensors. With the sensed imbalance current, a closed-loop control approach is proposed to adjust the modulation reference signal for each module to mitigate the remaining transient imbalance current. The proposed method is straightforward to implement with enhanced compatibility and flexibility compared to existing methods. Experimental studies are performed using inverters with 2 and 4 power modules paralleled in each phase to demonstrate the effectiveness of the proposed method.
- 20 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 582-587
A High-Power, High-Frequency Matrix Core Transformer Design for Medium Voltage Dual Active Bridge
In this work, the analytical models and optimization procedure for the design of high-power matrix core transformer (MCT) aiming at isolated DC/DC converter applications, especially for dual active bridge (DAB) converters, are proposed. The loss models, leakage inductance and thermal network models of MCT are presented, and a multi-variable, multi-objective optimization methodology of MCT is proposed. A 100 kW/50 kHz MCT design is selected and prototyped based on the optimization results. An additive manufactured bobbin design is also presented to control the leakage inductance and the path of the airflow. The electrical, magnetic, and thermal performance of the prototype are validated using by experimental studies.
- 20 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 582-587
A High-Power, High-Frequency Matrix Core Transformer Design for Medium Voltage Dual Active Bridge
In this work, the analytical models and optimization procedure for the design of high-power matrix core transformer (MCT) aiming at isolated DC/DC converter applications, especially for dual active bridge (DAB) converters, are proposed. The loss models, leakage inductance and thermal network models of MCT are presented, and a multi-variable, multi-objective optimization methodology of MCT is proposed. A 100 kW/50 kHz MCT design is selected and prototyped based on the optimization results. An additive manufactured bobbin design is also presented to control the leakage inductance and the path of the airflow. The electrical, magnetic, and thermal performance of the prototype are validated using by experimental studies.