Guojun Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guojun Xu has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chenzi Liao
School of Physics, Xi’an Jiaotong University, Xi’an 710049, P. R. China
1 shared publication James W. Summers
PolyOne Corporation, Avon Lake, OH 44012
1 shared publication- Jing-Jun Zhang
School of Physics and State Key Laboratory of Nuclear Physics and Technology Peking University 100871 Beijing China
1 shared publication - José García
AB Sandvik Coromant R&D, Lerkrogsvagen 19, SE-12680 Stockholm, Sweden
1 shared publication Kurt W. Koelling
Department of Chemical Engineering, The Ohio State University, Columbus, OH 43210
1 shared publication- Ying Zhang
School of Science Xi'an Jiaotong University 710049 Xi'an China
1 shared publication
Latest Publications
- 10 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
- Vol. 38 (25)
The structure of flavor mixing and reconstruction of the mass matrix
The fermion flavor structure is investigated by bilinear decomposition of the mass matrix after EW symmetry breaking, and the roles of factorized matrices in flavor mixing and mass generation are explored. On a new Yukawa basis, the minimal parameterization of flavor mixing is realized containing two relative phases and two free [ ] rotation angles. It is shown that flavor mixing can be addressed from four independent parameters. The validity of the flavor mixing structure is checked in both the lepton and quark sectors. Under the decomposition of flavor mixing, fermion mass matrices are reconstructed in the hierarchy limit. A flat mass matrix with all elements equal to 1 arises naturally from the requirement that homology exists between up-type and down-type fermion mass matrices. Some hints of a flat matrix and flavor breaking are also discussed.
- 10 September 2023
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics A
- Vol. 38 (25)
The structure of flavor mixing and reconstruction of the mass matrix
The fermion flavor structure is investigated by bilinear decomposition of the mass matrix after EW symmetry breaking, and the roles of factorized matrices in flavor mixing and mass generation are explored. On a new Yukawa basis, the minimal parameterization of flavor mixing is realized containing two relative phases and two free [ ] rotation angles. It is shown that flavor mixing can be addressed from four independent parameters. The validity of the flavor mixing structure is checked in both the lepton and quark sectors. Under the decomposition of flavor mixing, fermion mass matrices are reconstructed in the hierarchy limit. A flat mass matrix with all elements equal to 1 arises naturally from the requirement that homology exists between up-type and down-type fermion mass matrices. Some hints of a flat matrix and flavor breaking are also discussed.
- 1 March 2004
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 10 (1) , 17-40
PVC degradation during injection molding: Experimental evaluation
This paper focuses on experimental observations of poly(vinyl chloride) (PVC) degradation during injection molding. Degradation of poly(vinyl chloride) has been extensively studied. These studies have been performed in quiescent systems with very little or no strain applied to the sample. However, during processing, the polymer experiences very large deformations, in particular in the case of injection molding. This work demonstrates that the large shear during injection molding causes a significant increase of degradation as compared to studies in quiescent systems. It was also observed that degradation occurs in less than 1/10 the time required for quiescent systems. Finally, the flow geometry also affects the degradation behavior during processing. Understanding the parameters leading to degradation could lead to schemes to avoid it. J. Vinyl Addit. Technol. 10:17–40, 2004. © 2004 Society of Plastics Engineers.
- 1 March 2004
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 10 (1) , 17-40
PVC degradation during injection molding: Experimental evaluation
This paper focuses on experimental observations of poly(vinyl chloride) (PVC) degradation during injection molding. Degradation of poly(vinyl chloride) has been extensively studied. These studies have been performed in quiescent systems with very little or no strain applied to the sample. However, during processing, the polymer experiences very large deformations, in particular in the case of injection molding. This work demonstrates that the large shear during injection molding causes a significant increase of degradation as compared to studies in quiescent systems. It was also observed that degradation occurs in less than 1/10 the time required for quiescent systems. Finally, the flow geometry also affects the degradation behavior during processing. Understanding the parameters leading to degradation could lead to schemes to avoid it. J. Vinyl Addit. Technol. 10:17–40, 2004. © 2004 Society of Plastics Engineers.