JKJoachim Kaschta

Joachim Kaschta

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Joachim Kaschta has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Melt strain hardening of various high density polyethylenes

    by Helmut Münstedt, Joachim Kaschta

    Strain hardening of polymer melts is a rheological property interesting from an application and a fundamental point of view. While strain hardening of long-chain branched polyethylenes and polypropylenes and their relation to the molecular structure have widely been discussed in the literature, there are only few publications on the behavior of polyethylenes of high density (HDPE). Moreover, the results available from the literature are different with respect to the dependence of strain hardening on the elongational rate. Some samples show a negligible strain hardening, but most of them reveal hardening increasing with the decreasing rate. The lack of comprehensive molecular characterizations restricts a deeper understanding. Thus, in this work, the elongational behavior of various HDPEs was studied and their molecular structure characterized using high-temperature gel-permeation chromatography coupled with laser-light scattering at small elution volumes. In addition, the zero-shear viscosity as a function of molar mass was considered. It was found that molecules of very high molar masses or few long branches effecting long relaxation times may be the reason for strain hardening increasing with the decreasing rate. The underlying chemical reaction is not understood in detail, but it seems very probable that the catalysts and the processes used for the polymerization of HDPE may be able to generate molecular structures with a strong effect on strain hardening.


  • Open Access

    Characterization of the temperature and frequency dependency of the complex Poisson’s ratio using a novel combined torsional-axial rheometer

    by José Alberto Rodríguez Agudo, Jan Haeberle, Michael Müller-Pabel, Alexander Troiss, Abhishek Shetty, Joachim Kaschta, Christopher Giehl

    This study discusses the feasibility of using a combined torsional-axial rheometer to indirectly measure the complex Poisson’s ratio based on shear and Young’s modulus. For this purpose, isothermal frequency sweeps in torsion and extension are performed sequentially on the same cylindrical specimen and under the same environmental conditions. The method is tested on two amorphous polymers, a semicrystalline polymer, a polymer blend, and a copolymer. The article includes an extensive literature review and an uncertainty assessment of the method to provide a basis for subsequent data comparison with existing research. The experimental data show a monotonic increase in the complex Poisson’s ratio up to 0.5 as the temperature approaches α-relaxation for all samples, except for the amorphous polymer. The latter shows a local minimum in the complex Poisson’s ratio observed near α-relaxation, which disappears after thermal annealing of the sample above the α-relaxation temperature. The real and imaginary parts of the complex Poisson’s ratio are additionally determined by evaluating both phase shift angles from torsional and extensional measurements. All polymers show a certain offset between the torsional and extensional phase shift angles in the glassy state, which gradually decreases as the temperature approaches α-relaxation. The complex Poisson’s ratio results are in good agreement with the literature data obtained by existing methods. This confirms that the method is applicable to polymers up to α-relaxation temperatures with significant time savings due to the nondestructive approach. This is of particular interest, given the limited availability of data in the literature.


  • Simultaneous Determination of Electrical and Rheological Properties of Polypropylene Filled with Carbon Nanotubes

    by Christian Triebel, Joachim Kaschta, Nikolaos Katsikis, Helmut Münstedt, Andreas Funck, Walter Kaminsky, Albert Co, Gary L. Leal, Ralph H. Colby, A. Jeffrey Giacomin

    Composites of isotatic polypropylene (iPP) and carbon nanotubes (CNT) of different concentrations were prepared via an in‐situ polymerization using metallocene catalysts. Rheological properties as well as the electrical conductivity were measured simultaneously as a function of CNT‐concentration. A significant effect on the dynamic‐mechanical behaviour was found even far below the concentration of the electrical percolation threshold. In addition, the influence of the CNT on the elasticity as measured by the recoverable compliance in shear was determined. In the linear viscoelastic regime a significant increase of the recoverable compliance by adding carbon nanotubes was found. This finding is explained by an interaction between filler and matrix, which hinders the mobility of those matrix molecules being in contact with the CNT. These interactions are not related to the existence of a CNT percolation network as an increase of conductivity is not found simultaneously.


  • Superalloy IN625 with Cellular Microstructure – Fabrication Route and Mechanical Properties

    by P. Quadbeck, J. Kaschta, R.F. Singer

    Cellular microstructures are of special interest for applications in filtering, heat transfer or acoustic absorption. In the present paper a new route for the preparation of such structures from superalloys will be presented. Polyoxymethylene (POM) is used as space holder which can be injection molded into any desired shape. Densification of the cell walls and struts is achieved by supersolidus liquid phase sintering (SLPS).