Jiajia Sheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiajia Sheng has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Linbing Wang
School of Environmental, Civil, Agricultural and Mechanical Engineering, University of Georgia, Athens, GA 30602, USA
2 shared publications - Hailu Yang
National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication - Wenjing Ma
State Grid Qinghai Province Power Company Xining Power Supply Company, Xining 810003, China
1 shared publication - Xiaoming Kou
Gansu Provincial Highway Development Group Co., Ltd., Lanzhou 730070, China
1 shared publication - Xin Pang
Research Institute of Urbanization and Urban Safety, School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication - Yalin Liu
National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 102206, China
1 shared publication
Latest Publications
- Open Access
Study on the Impact of Diluent Dosages on the Epoxy–Polythiol Self-Healing System
Self-healing technology is an effective method for enhancing the crack resistance of cement-based composites. This study focuses on the impact of the environmentally friendly diluent C12-14 alkyl glycidyl ether (AGE) on the performance of the epoxy resin–polythiol (rimethylolpropane tris (3-mercaptopropionate), TMPMP) self-healing system, examining core fluidity, microcapsule properties, molecular dynamics, and the mechanical properties of cured products. The results show that as the AGE dosage increases, the particle size distribution of microcapsules becomes more concentrated, and the dispersion of particles is improved. Fourier-transform infrared spectroscopy confirms the successful encapsulation of E-51 and AGE. Microcapsules maintain structural integrity at high temperatures of 423.15 K. The onset thermal degradation temperature of the mixture shows an increasing trend with reduced AGE dosage. Specifically, TMPMP35% exhibits an onset degradation temperature of 370.95 K, while that of TMPMP20% is increased by 57.57% compared to TMPMP35%. Conversely, the initial and peak temperatures of the curing reaction decrease with less AGE incorporation. Thermodynamic analysis reveals that activation energy (E) initially increases and then decreases with increasing AGE. The frequency factor (A) correlates positively with the heating rate, indicating that the curing reaction’s reactivity is closely linked to heating rate. Minor variations in the reaction rate constant (k) indicate that the self-healing system maintains stable reactive activity at low temperatures. Notably, the AGE dosage significantly affects the rigidity of the self-healing system; the average Young’s modulus inversely correlates with AGE dosage, with the most substantial decrease of 5.88% occurring when AGE increases from 30% to 35%. This study offers insights into optimizing diluent ratios to balance self-healing and mechanical properties, essential for developing high-performance self-healing cement materials.
Open AccessStudy on the Impact of Diluent Dosages on the Epoxy–Polythiol Self-Healing System
Self-healing technology is an effective method for enhancing the crack resistance of cement-based composites. This study focuses on the impact of the environmentally friendly diluent C12-14 alkyl glycidyl ether (AGE) on the performance of the epoxy resin–polythiol (rimethylolpropane tris (3-mercaptopropionate), TMPMP) self-healing system, examining core fluidity, microcapsule properties, molecular dynamics, and the mechanical properties of cured products. The results show that as the AGE dosage increases, the particle size distribution of microcapsules becomes more concentrated, and the dispersion of particles is improved. Fourier-transform infrared spectroscopy confirms the successful encapsulation of E-51 and AGE. Microcapsules maintain structural integrity at high temperatures of 423.15 K. The onset thermal degradation temperature of the mixture shows an increasing trend with reduced AGE dosage. Specifically, TMPMP35% exhibits an onset degradation temperature of 370.95 K, while that of TMPMP20% is increased by 57.57% compared to TMPMP35%. Conversely, the initial and peak temperatures of the curing reaction decrease with less AGE incorporation. Thermodynamic analysis reveals that activation energy (E) initially increases and then decreases with increasing AGE. The frequency factor (A) correlates positively with the heating rate, indicating that the curing reaction’s reactivity is closely linked to heating rate. Minor variations in the reaction rate constant (k) indicate that the self-healing system maintains stable reactive activity at low temperatures. Notably, the AGE dosage significantly affects the rigidity of the self-healing system; the average Young’s modulus inversely correlates with AGE dosage, with the most substantial decrease of 5.88% occurring when AGE increases from 30% to 35%. This study offers insights into optimizing diluent ratios to balance self-healing and mechanical properties, essential for developing high-performance self-healing cement materials.
- Open Access
- 6 November 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (21) , 15667
An Assessment of the Impact of Climate Change on Asphalt Binder Selection in East China Based on the ARIMA Model
Temperature is a key factor considered in the selection of asphalt binders for asphalt pavement construction. Currently, the asphalt binders used in some regions’ asphalt pavements are no longer suitable for anticipated climate conditions. The reasonable selection of asphalt binder is an important measure for asphalt pavement to adapt to climate change. This paper focuses on the potential impact of climate change on asphalt binder selection in East China in the future. This study is based on the performance grade (PG) system with SUPERPAVE specifications. It involved collecting meteorological data from 109 meteorological stations in East China from 1960 to 2019 and used the ARIMA prediction model to calculate the maximum and minimum design temperatures for road surfaces over the next 20 years. Based on the forecasted road surface temperature data, the impact of climate change on the choice of asphalt binder in East China was discussed. The research findings indicate that, validated by historical data, using the ARIMA model for future temperature prediction has proven reliability. There are some differences in different regions regarding the change in maximum and minimum pavement design temperatures. In 2019 and 2039, there are three and four high temperature grades in East China; these are PG52, PG58, and PG64 and PG52, PG58, and PG64, PG70 respectively. The dominant high temperature grade in East China will remain PG64, and a total of 23.80% of the regions in East China will experience a one-grade upward shift in high temperature grades. PG-28, PG-22, PG-16, and PG-10 are the four low temperature grades distributed in East China in both 2019 and 2039. Compared with 2019, the proportion of areas with grade PG-16 will increase from 33.86% to 34.89%, and the dominant low temperature grade in East China will remain PG-10 in 2039. In the next 20 years, low-temperature cracking issues related to asphalt pavement in some areas of East China will intensify, but the primary challenge will still be problems caused by high temperatures.
- 6 November 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (21) , 15667
Open AccessAn Assessment of the Impact of Climate Change on Asphalt Binder Selection in East China Based on the ARIMA Model
Temperature is a key factor considered in the selection of asphalt binders for asphalt pavement construction. Currently, the asphalt binders used in some regions’ asphalt pavements are no longer suitable for anticipated climate conditions. The reasonable selection of asphalt binder is an important measure for asphalt pavement to adapt to climate change. This paper focuses on the potential impact of climate change on asphalt binder selection in East China in the future. This study is based on the performance grade (PG) system with SUPERPAVE specifications. It involved collecting meteorological data from 109 meteorological stations in East China from 1960 to 2019 and used the ARIMA prediction model to calculate the maximum and minimum design temperatures for road surfaces over the next 20 years. Based on the forecasted road surface temperature data, the impact of climate change on the choice of asphalt binder in East China was discussed. The research findings indicate that, validated by historical data, using the ARIMA model for future temperature prediction has proven reliability. There are some differences in different regions regarding the change in maximum and minimum pavement design temperatures. In 2019 and 2039, there are three and four high temperature grades in East China; these are PG52, PG58, and PG64 and PG52, PG58, and PG64, PG70 respectively. The dominant high temperature grade in East China will remain PG64, and a total of 23.80% of the regions in East China will experience a one-grade upward shift in high temperature grades. PG-28, PG-22, PG-16, and PG-10 are the four low temperature grades distributed in East China in both 2019 and 2039. Compared with 2019, the proportion of areas with grade PG-16 will increase from 33.86% to 34.89%, and the dominant low temperature grade in East China will remain PG-10 in 2039. In the next 20 years, low-temperature cracking issues related to asphalt pavement in some areas of East China will intensify, but the primary challenge will still be problems caused by high temperatures.