Fan Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fan Zhao has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hairong Wang
Xi An Jiao Tong Univ, State Key Lab Mfg Syst Engn, Xian 710049, Shaanxi, Peoples R China
4 shared publications Jingfeng Wang
Research Institute of Chemical Defense, Beijing 102205, China
2 shared publicationsLingmin Yu
School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an, Shaanxi 710021, China
2 shared publicationsPu-Hong Wang
Research Institute of Chemical Defense, Beijing 102205, China
2 shared publicationsRuihao Wang
State Key Laboratory for Manufacturing Systems Engineering
2 shared publicationsWei Cao
Research Institute of Chemical Defense, Beijing 102205, China
2 shared publications
Latest Publications
- 5 June 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (6) , 4763-4774
Machine Learning-Enabled Gas Sensor Based on MOF-Derived In 2 O 3 –CuO for Exhaled CO Detection
Noninvasive, precise breath analysis holds significant importance for the screening and monitoring of neonatal jaundice, with its core challenge lying in the specific detection of the key biomarker carbon monoxide (CO) within complex breath matrices. This research employed a controlled process to fabricate five sets of In2O3–CuO sensors derived from bimetallic metal–organic frameworks (Bi MOFs). These were assembled into a microsensor array, and by incorporating a linear discriminant analysis algorithm, an electronic nose system was constructed. This approach utilizes thermodynamic feature engineering to enhance data validity and optimize algorithm selection, thereby reducing reliance on large-scale data and computational resources. By integrating thermodynamically feature-driven machine learning, the electronic nose system-comprising merely five In2O3–CuO sensors-ultimately achieved accurate discrimination between CO and acetone. Concurrently, the single 3In2O3–CuO sensor exhibits excellent reproducibility, moisture resistance, and stability, with a low detection limit of 1 ppm and relatively rapid response/recovery times (5/21 s). By introducing machine learning algorithms to analyze the multidimensional response signals from the sensor array, the study successfully addressed the cross-sensitivity issue between CO and coexisting interfering gas C3H6O in clinical environments, achieving qualitative identification of CO ranging from 1 to 50 ppm (cross-validation accuracy reached 82%), providing a highly reliable technical platform for noninvasive screening of neonatal bilirubin metabolic abnormalities.
- 5 June 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (6) , 4763-4774
Machine Learning-Enabled Gas Sensor Based on MOF-Derived In 2 O 3 –CuO for Exhaled CO Detection
Noninvasive, precise breath analysis holds significant importance for the screening and monitoring of neonatal jaundice, with its core challenge lying in the specific detection of the key biomarker carbon monoxide (CO) within complex breath matrices. This research employed a controlled process to fabricate five sets of In2O3–CuO sensors derived from bimetallic metal–organic frameworks (Bi MOFs). These were assembled into a microsensor array, and by incorporating a linear discriminant analysis algorithm, an electronic nose system was constructed. This approach utilizes thermodynamic feature engineering to enhance data validity and optimize algorithm selection, thereby reducing reliance on large-scale data and computational resources. By integrating thermodynamically feature-driven machine learning, the electronic nose system-comprising merely five In2O3–CuO sensors-ultimately achieved accurate discrimination between CO and acetone. Concurrently, the single 3In2O3–CuO sensor exhibits excellent reproducibility, moisture resistance, and stability, with a low detection limit of 1 ppm and relatively rapid response/recovery times (5/21 s). By introducing machine learning algorithms to analyze the multidimensional response signals from the sensor array, the study successfully addressed the cross-sensitivity issue between CO and coexisting interfering gas C3H6O in clinical environments, achieving qualitative identification of CO ranging from 1 to 50 ppm (cross-validation accuracy reached 82%), providing a highly reliable technical platform for noninvasive screening of neonatal bilirubin metabolic abnormalities.
- 10 February 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 216
Oxygen-dependent thickness effects in PdAu MEMS hydrogen sensors: From inert-gas benchmarks to real-air operation
- 10 February 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 216
Oxygen-dependent thickness effects in PdAu MEMS hydrogen sensors: From inert-gas benchmarks to real-air operation
- 3 December 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (12) , 127503
Low Concentration C2H2 Detection by NiO/SnO2 Nanostructured Heterojunction Based MEMS Sensor
Low concentration detection and analysis of dissolved characteristic gas Acetylene (C2H2) in oil is one of the effective methods for power transformer condition maintenance to ensure safety. The MEMS gas sensor based on the nanostructured material has become a research hotpot for detecting the C2H2. In this work, SnO2 and NiO thin films were successively deposited by RF sputtering, followed by annealing at different temperatures to prepare NiO/SnO2 heterostructures, and the C2H2 sensor chips were prepared by MEMS (microelectromechanical systems) compatible process by using the SnO2/NiO thin films as sensitive materials. The results showed that the detection limit of the MEMS sensor based on the NiO/SnO2 (NiO/SnO2-2) film annealed at 450 °C was as low as 0.2 × 10−6 toward C2H2. The sensor exhibits a high response at 260 °C (S = 7.9 toward 1.4 × 10−6 C2H2), which is about 4.5 times that of pure SnO2(1.8). Meanwhile, it has an extremely short response time (13 s and 19 s). This study reveals that dissolved acetylene gas in transformer oil can be detected more efficiently by the sensor with nanostructured heterojunctions as sensitive materials.
- 3 December 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (12) , 127503
Low Concentration C2H2 Detection by NiO/SnO2 Nanostructured Heterojunction Based MEMS Sensor
Low concentration detection and analysis of dissolved characteristic gas Acetylene (C2H2) in oil is one of the effective methods for power transformer condition maintenance to ensure safety. The MEMS gas sensor based on the nanostructured material has become a research hotpot for detecting the C2H2. In this work, SnO2 and NiO thin films were successively deposited by RF sputtering, followed by annealing at different temperatures to prepare NiO/SnO2 heterostructures, and the C2H2 sensor chips were prepared by MEMS (microelectromechanical systems) compatible process by using the SnO2/NiO thin films as sensitive materials. The results showed that the detection limit of the MEMS sensor based on the NiO/SnO2 (NiO/SnO2-2) film annealed at 450 °C was as low as 0.2 × 10−6 toward C2H2. The sensor exhibits a high response at 260 °C (S = 7.9 toward 1.4 × 10−6 C2H2), which is about 4.5 times that of pure SnO2(1.8). Meanwhile, it has an extremely short response time (13 s and 19 s). This study reveals that dissolved acetylene gas in transformer oil can be detected more efficiently by the sensor with nanostructured heterojunctions as sensitive materials.
- 5 November 2024
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 9 (11) , 6082-6091
Wheatstone Bridge MEMS Hydrogen Sensor with ppb-Level Detection Limit Based on the Palladium–Gold Alloy
On some occasions, such as new energy clinics, monitoring the trace hydrogen at the ppb level is necessary. The traditional resistive hydrogen sensors based on the Pd alloys are very difficult to realize such an extremely low detection limit. To achieve a detection limit at the ppb level and also ensure good stability, a MEMS hydrogen sensor was designed in a suspended Wheatstone bridge structure, with all four resistive arms defined on a sputtered Pd-Au alloy thin film. For the Wheatstone bridge sensor, absolute response (Ra) and relative response (Rs) are defined to describe the sensitivity of the sensor, and the effect of annealing temperature on baseline drift is investigated using the baseline zero drift parameter (DBZD). By testing the sensors across a hydrogen concentration range of 20 ppb to 3 v/v%, the optimal annealing temperature (250 °C) and operating temperature (60 °C) were identified. Under these conditions, the sensor exhibited a detection limit as low as 20 ppb with a power consumption of only 4.6 mW. At the same time, the response and recovery times of the sensor were 6 and 19 s, respectively, toward 3 v/v% hydrogen. After testing over a 100-day period, Ra fluctuated only 0.0026%, indicating that the hydrogen sensor had good long-term stability for low-concentration detection. More results also showed that the sensor has good repeatability, selectivity, and humidity resistance. With the wide measurement range (20 ppb to 3 v/v%), the sensor has the potential to meet hydrogen detection requirements in multiple scenarios.
- 5 November 2024
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 9 (11) , 6082-6091
Wheatstone Bridge MEMS Hydrogen Sensor with ppb-Level Detection Limit Based on the Palladium–Gold Alloy
On some occasions, such as new energy clinics, monitoring the trace hydrogen at the ppb level is necessary. The traditional resistive hydrogen sensors based on the Pd alloys are very difficult to realize such an extremely low detection limit. To achieve a detection limit at the ppb level and also ensure good stability, a MEMS hydrogen sensor was designed in a suspended Wheatstone bridge structure, with all four resistive arms defined on a sputtered Pd-Au alloy thin film. For the Wheatstone bridge sensor, absolute response (Ra) and relative response (Rs) are defined to describe the sensitivity of the sensor, and the effect of annealing temperature on baseline drift is investigated using the baseline zero drift parameter (DBZD). By testing the sensors across a hydrogen concentration range of 20 ppb to 3 v/v%, the optimal annealing temperature (250 °C) and operating temperature (60 °C) were identified. Under these conditions, the sensor exhibited a detection limit as low as 20 ppb with a power consumption of only 4.6 mW. At the same time, the response and recovery times of the sensor were 6 and 19 s, respectively, toward 3 v/v% hydrogen. After testing over a 100-day period, Ra fluctuated only 0.0026%, indicating that the hydrogen sensor had good long-term stability for low-concentration detection. More results also showed that the sensor has good repeatability, selectivity, and humidity resistance. With the wide measurement range (20 ppb to 3 v/v%), the sensor has the potential to meet hydrogen detection requirements in multiple scenarios.
- 30 July 2024
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 9 (8) , 4007-4016
Metal–Organic Framework-Derived Au-Doped In2O3 Nanotubes for Monitoring CO at the ppb Level
Achieving selective detection of ppb-level CO is important for air quality testing at industrial sites to ensure personal safety. Noble metal doping enhances charge transfer, which in turn reduces the detection limit of metal oxide gas sensors. In this work, metal-organic framework-derived Au-doped In2O3 nanotubes with high electrical conductivity are synthesized by pyrolysis of the Au-doped metal-organic framework (In-MIL-68) as a template. Gas-sensing experiments reveal that the detection limit of 0.2% Au-doped In2O3 nanotubes (0.2% Au, mass fraction) is as low as 750 ppb. Meanwhile, the sensing material shows a response value of 18.2 to 50 ppm of CO at 240 °C, which is about 2.8 times higher than that of pure In2O3. Meanwhile, the response and recovery times are short (37 s/86 s). The gas-sensing mechanism of CO is uncovered by in situ DRIFTS through the reaction intermediates. In addition, first-principles calculations suggest that Au doping of In2O3 significantly enhances its adsorption energy for CO and improves the electron transfer properties. This study reveals a novel synthesis pathway for Au-doped In2O3 nanotubular structures and their potential application in low concentration CO detection.
- 30 July 2024
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 9 (8) , 4007-4016
Metal–Organic Framework-Derived Au-Doped In2O3 Nanotubes for Monitoring CO at the ppb Level
Achieving selective detection of ppb-level CO is important for air quality testing at industrial sites to ensure personal safety. Noble metal doping enhances charge transfer, which in turn reduces the detection limit of metal oxide gas sensors. In this work, metal-organic framework-derived Au-doped In2O3 nanotubes with high electrical conductivity are synthesized by pyrolysis of the Au-doped metal-organic framework (In-MIL-68) as a template. Gas-sensing experiments reveal that the detection limit of 0.2% Au-doped In2O3 nanotubes (0.2% Au, mass fraction) is as low as 750 ppb. Meanwhile, the sensing material shows a response value of 18.2 to 50 ppm of CO at 240 °C, which is about 2.8 times higher than that of pure In2O3. Meanwhile, the response and recovery times are short (37 s/86 s). The gas-sensing mechanism of CO is uncovered by in situ DRIFTS through the reaction intermediates. In addition, first-principles calculations suggest that Au doping of In2O3 significantly enhances its adsorption energy for CO and improves the electron transfer properties. This study reveals a novel synthesis pathway for Au-doped In2O3 nanotubular structures and their potential application in low concentration CO detection.
- 3 November 2023
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 8 (12) , 4577-4586
Fast and Sensitive Detection of CO by Bi-MOF-Derived Porous In2O3/Fe2O3 Core–Shell Nanotubes
In2O3 is an optimal material for sensitive detection of carbon monoxide (CO) gas due to its low resistivity and high catalytic activity. Yet, the gas response dynamics between the CO gas molecules and the surface of In2O3 is limited by its solid structure, resulting in a weak gas response value and sluggish electron transport. Herein, we report a strategy to synthesize porous In2O3/Fe2O3 core-shell nanotubes derived from In/Fe bimetallic organic frameworks. The fabricated porous In2O3/Fe2O3-4 core-shell nanotubes present outstanding gas sensitivities, including a response value 3.8 times (33.7 to 200 ppm CO at 260 °C) higher than that of monometallic-derived In2O3 (8.7), ultrashort response and recovery times (23/76 s) to 200 ppm CO, low detection limit (1 ppm), promising selectivity, and long-term stability. The enhanced sensing mechanisms are clarified by the combination of experiment and first-principles calculations, showing that the synergetic strategy of higher adsorption energy, increased electrical conductivity, higher electron transfer numbers, and larger specific surface area of porous core-shell structures promotes the surface activity and charge transfer efficiency. The present work paves a way to tune gas-sensing materials with special morphologies for the development of high-performance CO sensors.
- 3 November 2023
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 8 (12) , 4577-4586
Fast and Sensitive Detection of CO by Bi-MOF-Derived Porous In2O3/Fe2O3 Core–Shell Nanotubes
In2O3 is an optimal material for sensitive detection of carbon monoxide (CO) gas due to its low resistivity and high catalytic activity. Yet, the gas response dynamics between the CO gas molecules and the surface of In2O3 is limited by its solid structure, resulting in a weak gas response value and sluggish electron transport. Herein, we report a strategy to synthesize porous In2O3/Fe2O3 core-shell nanotubes derived from In/Fe bimetallic organic frameworks. The fabricated porous In2O3/Fe2O3-4 core-shell nanotubes present outstanding gas sensitivities, including a response value 3.8 times (33.7 to 200 ppm CO at 260 °C) higher than that of monometallic-derived In2O3 (8.7), ultrashort response and recovery times (23/76 s) to 200 ppm CO, low detection limit (1 ppm), promising selectivity, and long-term stability. The enhanced sensing mechanisms are clarified by the combination of experiment and first-principles calculations, showing that the synergetic strategy of higher adsorption energy, increased electrical conductivity, higher electron transfer numbers, and larger specific surface area of porous core-shell structures promotes the surface activity and charge transfer efficiency. The present work paves a way to tune gas-sensing materials with special morphologies for the development of high-performance CO sensors.