Sushma Raghuvansy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sushma Raghuvansy has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Karg
Institut für Festkörperphysik, Universität Bremen, Otto-Hahn-Allee 1, 28359 Bremen, Germany
5 shared publications - Manuel Alonso-Orts
University of Bremen
5 shared publications - Martin S. Williams
Institute of Solid-State Physics, University of Bremen 1 , Otto-Hahn-Allee 1, 28359 Bremen, Germany
5 shared publications - Andreas Rosenauer
University of Bremen, Institute for Solid State Physics, Bremen, Germany
4 shared publications - Marco Schowalter
MAPEX Center for Materials and Processes University of Bremen Bibliothekstr. 1 28359 Bremen Germany
4 shared publications - Patrick Vogt
Max Planck Institute for Solid State Research 2 , Heisenbergstr. 1, 70569 Stuttgart
4 shared publications
Latest Publications
- Open Access
- 15 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (11)
Lattice parameters and elastic properties for strain analysis in κ-(InxGa1−x)2O3/κ-Ga2O3/Al2O3 heterostructures from density functional theory, x-ray diffraction, and scanning precession nanobeam electron diffraction
In this publication, we study strain in κ-(InxGa1−x)2O3/κ-Ga2O3/Al2O3 heterostructures grown by plasma-assisted molecular beam epitaxy using a combination of density functional theory (DFT), x-ray diffraction (XRD), nanobeam electron diffraction (NBED), and energy-dispersive x-ray spectroscopy (EDX) for layers with low (2%) and high (18%) In concentration. Lattice parameters and elastic moduli were computed using the density functional theory formalism. The strain between κ-(InxGa1−x)2O3 and κ-Ga2O3 as well as Al2O3 and κ-Ga2O3 was measured in two different zone axes by NBED. Due to the quasi-hexagonality of the κ-phase, this yields an approximation for the full strain tensor. The obtained NBED results are supported by reciprocal space maps from XRD measurements. The relaxation of the layers was analyzed by comparing the measured strain data with those computed from the DFT lattice parameters and elastic moduli using the element concentrations measured by EDX, thus allowing for direct validation of the theoretical calculations by experimental data. This analysis results in satisfactory agreement and reveals that the layer with a low In concentration is fully strained (measured εzz=0.0037, computed εzz=0.0039), whereas the layer with high In concentration is fully relaxed (measured εzz=0.0222, computed εzz=0.0219). NBED, XRD, and theoretical predictions agree within their respective error margins for the strain between κ-(InxGa1−x)2O3 and κ-Ga2O3. Overall, the absolute value of the strain between κ-Ga2O3 and Al2O3 was measured to be smaller by NBED (measured εzz=−0.0628) and XRD than it was computed from literature lattice parameters (εzz=−0.0716).
- 15 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (11)
Open AccessLattice parameters and elastic properties for strain analysis in κ-(InxGa1−x)2O3/κ-Ga2O3/Al2O3 heterostructures from density functional theory, x-ray diffraction, and scanning precession nanobeam electron diffraction
In this publication, we study strain in κ-(InxGa1−x)2O3/κ-Ga2O3/Al2O3 heterostructures grown by plasma-assisted molecular beam epitaxy using a combination of density functional theory (DFT), x-ray diffraction (XRD), nanobeam electron diffraction (NBED), and energy-dispersive x-ray spectroscopy (EDX) for layers with low (2%) and high (18%) In concentration. Lattice parameters and elastic moduli were computed using the density functional theory formalism. The strain between κ-(InxGa1−x)2O3 and κ-Ga2O3 as well as Al2O3 and κ-Ga2O3 was measured in two different zone axes by NBED. Due to the quasi-hexagonality of the κ-phase, this yields an approximation for the full strain tensor. The obtained NBED results are supported by reciprocal space maps from XRD measurements. The relaxation of the layers was analyzed by comparing the measured strain data with those computed from the DFT lattice parameters and elastic moduli using the element concentrations measured by EDX, thus allowing for direct validation of the theoretical calculations by experimental data. This analysis results in satisfactory agreement and reveals that the layer with a low In concentration is fully strained (measured εzz=0.0037, computed εzz=0.0039), whereas the layer with high In concentration is fully relaxed (measured εzz=0.0222, computed εzz=0.0219). NBED, XRD, and theoretical predictions agree within their respective error margins for the strain between κ-(InxGa1−x)2O3 and κ-Ga2O3. Overall, the absolute value of the strain between κ-Ga2O3 and Al2O3 was measured to be smaller by NBED (measured εzz=−0.0628) and XRD than it was computed from literature lattice parameters (εzz=−0.0716).
- Open Access
- 1 September 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (9)
Composition and strain of the pseudomorphic α-phase intermediate layer at the Ga2O3/Al2O3 interface
We investigate the composition of α-phase intermediate layers at epitaxial Ga2O3/Al2O3 interfaces using high angle annular dark field scanning transmission electron microscopy. Their presence is considered a general phenomenon as they are observed independent of the growth technique [Schewski et al., Appl. Phys. Exp. 8, 011101]. Samples were grown by plasma assisted molecular beam epitaxy using different growth conditions. Almost independent of these, the quantitative evaluation of the measured intensities gave Ga concentrations of ∼25%. We show that the previously published model, based on a pure α-Ga2O3 interlayer, fails if it is adapted to the measured composition. Density functional theory (DFT) computations were used to overcome the approximations made in this model and suggest that a stabilization of the layer is possible due to the low Ga concentration (≤35%) at which the α-phase is the most stable. Our surface model computations suggest an exchange of Ga atoms at the surface with Al atoms from the underlying substrate as a possible formation mechanism.
- 1 September 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (9)
Open AccessComposition and strain of the pseudomorphic α-phase intermediate layer at the Ga2O3/Al2O3 interface
We investigate the composition of α-phase intermediate layers at epitaxial Ga2O3/Al2O3 interfaces using high angle annular dark field scanning transmission electron microscopy. Their presence is considered a general phenomenon as they are observed independent of the growth technique [Schewski et al., Appl. Phys. Exp. 8, 011101]. Samples were grown by plasma assisted molecular beam epitaxy using different growth conditions. Almost independent of these, the quantitative evaluation of the measured intensities gave Ga concentrations of ∼25%. We show that the previously published model, based on a pure α-Ga2O3 interlayer, fails if it is adapted to the measured composition. Density functional theory (DFT) computations were used to overcome the approximations made in this model and suggest that a stabilization of the layer is possible due to the low Ga concentration (≤35%) at which the α-phase is the most stable. Our surface model computations suggest an exchange of Ga atoms at the surface with Al atoms from the underlying substrate as a possible formation mechanism.
- Open Access
- 1 January 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (1)
Erratum: “Growth of β-Ga2O3 and ε/κ-Ga2O3 on AlN(0001) by molecular-beam epitaxy” [APL Mater. 11, 111113 (2023)]
It was brought to our attention that Fig. 1 in the published version of our paper1 is incorrect and does not represent the growth rate diagrams (Γ-diagrams) of
- 1 January 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (1)
Open AccessErratum: “Growth of β-Ga2O3 and ε/κ-Ga2O3 on AlN(0001) by molecular-beam epitaxy” [APL Mater. 11, 111113 (2023)]
It was brought to our attention that Fig. 1 in the published version of our paper1 is incorrect and does not represent the growth rate diagrams (Γ-diagrams) of
- Open Access
- 1 January 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (1)
Growth, catalysis, and faceting of α-Ga2O3 and α-(InxGa1−x)2O3 on m-plane α-Al2O3 by molecular beam epitaxy
The growth of α-Ga2O3 and α-(InxGa1−x)2O3 on m-plane α-Al2O3(101̄0) by molecular beam epitaxy (MBE) and metal-oxide-catalyzed epitaxy (MOCATAXY) is investigated. By systematically exploring the parameter space accessed by MBE and MOCATAXY, phase-pure α-Ga2O3(101̄0) and α-(InxGa1−x)2O3(101̄0) thin films are realized. The presence of In on the α-Ga2O3 growth surface remarkably expands its growth window far into the metal-rich flux regime and to higher growth temperatures. With increasing O-to-Ga flux ratio (RO), In incorporates into α-(InxGa1−x)2O3 up to x ≤ 0.08. Upon a critical thickness, β-(InxGa1−x)2O3 nucleates and, subsequently, heteroepitaxially grows on top of α-(InxGa1−x)2O3 facets. Metal-rich MOCATAXY growth conditions, where α-Ga2O3 would not conventionally stabilize, lead to single-crystalline α-Ga2O3 with negligible In incorporation and improved surface morphology. Higher TTC further results in single-crystalline α-Ga2O3 with well-defined terraces and step edges at their surfaces. For RO ≤ 0.53, In acts as a surfactant on the α-Ga2O3 growth surface by favoring step edges, while for RO ≥ 0.8, In incorporates and leads to a-plane α-(InxGa1−x)2O3 faceting and the subsequent (2̄01) β-(InxGa1−x)2O3 growth on top. Thin film analysis by scanning transmission electron microscopy reveals highly crystalline α-Ga2O3 layers and interfaces. We provide a phase diagram to guide the MBE and MOCATAXY growth of single-crystalline α-Ga2O3 on α-Al2O3(101̄0).
- 1 January 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (1)
Open AccessGrowth, catalysis, and faceting of α-Ga2O3 and α-(InxGa1−x)2O3 on m-plane α-Al2O3 by molecular beam epitaxy
The growth of α-Ga2O3 and α-(InxGa1−x)2O3 on m-plane α-Al2O3(101̄0) by molecular beam epitaxy (MBE) and metal-oxide-catalyzed epitaxy (MOCATAXY) is investigated. By systematically exploring the parameter space accessed by MBE and MOCATAXY, phase-pure α-Ga2O3(101̄0) and α-(InxGa1−x)2O3(101̄0) thin films are realized. The presence of In on the α-Ga2O3 growth surface remarkably expands its growth window far into the metal-rich flux regime and to higher growth temperatures. With increasing O-to-Ga flux ratio (RO), In incorporates into α-(InxGa1−x)2O3 up to x ≤ 0.08. Upon a critical thickness, β-(InxGa1−x)2O3 nucleates and, subsequently, heteroepitaxially grows on top of α-(InxGa1−x)2O3 facets. Metal-rich MOCATAXY growth conditions, where α-Ga2O3 would not conventionally stabilize, lead to single-crystalline α-Ga2O3 with negligible In incorporation and improved surface morphology. Higher TTC further results in single-crystalline α-Ga2O3 with well-defined terraces and step edges at their surfaces. For RO ≤ 0.53, In acts as a surfactant on the α-Ga2O3 growth surface by favoring step edges, while for RO ≥ 0.8, In incorporates and leads to a-plane α-(InxGa1−x)2O3 faceting and the subsequent (2̄01) β-(InxGa1−x)2O3 growth on top. Thin film analysis by scanning transmission electron microscopy reveals highly crystalline α-Ga2O3 layers and interfaces. We provide a phase diagram to guide the MBE and MOCATAXY growth of single-crystalline α-Ga2O3 on α-Al2O3(101̄0).
- Open Access
- 1 November 2023
- Published by AIP Publishing in APL Materials
- Vol. 11 (11)
Growth of β-Ga2O3 and ϵ/κ-Ga2O3 on AlN(0001) by molecular-beam epitaxy
The heteroepitaxial growth and phase formation of Ga2O3 on Al-polar AlN(0001) templates by molecular-beam epitaxy (MBE) are studied. Three different MBE approaches are employed: (i) conventional MBE, (ii) suboxide MBE (S-MBE), and (iii) metal-oxide-catalyzed epitaxy (MOCATAXY). We grow phase-pure β-Ga2O3(2̄01) and phase-pure ϵ/κ-Ga2O3(001) with smooth surfaces by S-MBE and MOCATAXY. Thin film analysis shows that the crystallographic and surface features of the β-Ga2O3(2̄01)/AlN(0001) and ϵ/κ-Ga2O3(001)/AlN(0001) epilayers are of high crystalline quality. Growth and phase diagrams are developed to synthesize Ga2O3 on AlN by MBE and MOCATAXY and to provide guidance to grow Ga2O3 on several non-oxide surfaces, e.g., AlN, GaN, and SiC, by MBE, S-MBE, and MOCATAXY.
- 1 November 2023
- Published by AIP Publishing in APL Materials
- Vol. 11 (11)
Open AccessGrowth of β-Ga2O3 and ϵ/κ-Ga2O3 on AlN(0001) by molecular-beam epitaxy
The heteroepitaxial growth and phase formation of Ga2O3 on Al-polar AlN(0001) templates by molecular-beam epitaxy (MBE) are studied. Three different MBE approaches are employed: (i) conventional MBE, (ii) suboxide MBE (S-MBE), and (iii) metal-oxide-catalyzed epitaxy (MOCATAXY). We grow phase-pure β-Ga2O3(2̄01) and phase-pure ϵ/κ-Ga2O3(001) with smooth surfaces by S-MBE and MOCATAXY. Thin film analysis shows that the crystallographic and surface features of the β-Ga2O3(2̄01)/AlN(0001) and ϵ/κ-Ga2O3(001)/AlN(0001) epilayers are of high crystalline quality. Growth and phase diagrams are developed to synthesize Ga2O3 on AlN by MBE and MOCATAXY and to provide guidance to grow Ga2O3 on several non-oxide surfaces, e.g., AlN, GaN, and SiC, by MBE, S-MBE, and MOCATAXY.