Edwin Joseph Munoz Lopez
Edwin Joseph Munoz Lopez has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Hergt
Institute of Propulsion Technology, German Aerospace Center (DLR), Linder Höhe, 51147 Cologne, Germany
6 shared publications - Volker Gümmer
Chair of Turbomachinery and Flight Propulsion, Technical University of Munich, Garching, Bavaria 85748, Germany
3 shared publications - Bjoern F. Klose
Institute of Test and Simulation for Gas Turbines, German Aerospace Center (DLR), Linder Höhe, 51147 Cologne, Germany
2 shared publications - Christian Willert
DLR Institute of Propulsion Technology, German Aerospace Center, Köln, Germany
2 shared publications - Joachim Klinner
German Aerospace Center (DLR), Institute of Propulsion Technology, 51147 Cologne, Germany
2 shared publications - Sebastian Grund
German Aerospace Center (DLR), Institute of Propulsion Technology, 51147 Cologne, Germany
2 shared publications
Latest Publications
- Open Access
- 2 July 2025
- Published by Springer Nature
- p. 297-324
Experimental and Numerical Investigations of SBLI and Flow Control on a Transonic Compressor Cascade
The flow through a transonic compressor cascade is inherently unsteady due to the shock-boundary layer interactions (SBLI) on the blade. Despite decades of research, few details are known about the mechanisms that cause such behavior. This chapter presents a multidisciplinary study aiming to elucidate these mechanisms and optimize flow control methods to mitigate their effects. For this purpose, the Transonic Cascade TEAMAero was first optimized and its performance was validated experimentally. The cycle of shock oscillation was then compared using advanced experimental measurement techniques and high-fidelity LES. This comparison revealed a continuous propagation of pressure waves from a point upstream of the trailing edge. The interaction of these waves with the main bow shock at different points of the cycle was then linked to the frequencies observed in the oscillation spectrum. A configuration of this cascade with two roughness patches was finally optimized using a novel procedure developed. The optimal configurations obtained show how the targeted design of these devices can simultaneously mitigate shock oscillations and improve performance. This chapter demonstrates how the combined application of advanced numerical and experimental techniques needs to be intensified as researchers search for a global theory of SBLI in compressor blades.
- 2 July 2025
- Published by Springer Nature
- p. 297-324
Open AccessExperimental and Numerical Investigations of SBLI and Flow Control on a Transonic Compressor Cascade
The flow through a transonic compressor cascade is inherently unsteady due to the shock-boundary layer interactions (SBLI) on the blade. Despite decades of research, few details are known about the mechanisms that cause such behavior. This chapter presents a multidisciplinary study aiming to elucidate these mechanisms and optimize flow control methods to mitigate their effects. For this purpose, the Transonic Cascade TEAMAero was first optimized and its performance was validated experimentally. The cycle of shock oscillation was then compared using advanced experimental measurement techniques and high-fidelity LES. This comparison revealed a continuous propagation of pressure waves from a point upstream of the trailing edge. The interaction of these waves with the main bow shock at different points of the cycle was then linked to the frequencies observed in the oscillation spectrum. A configuration of this cascade with two roughness patches was finally optimized using a novel procedure developed. The optimal configurations obtained show how the targeted design of these devices can simultaneously mitigate shock oscillations and improve performance. This chapter demonstrates how the combined application of advanced numerical and experimental techniques needs to be intensified as researchers search for a global theory of SBLI in compressor blades.
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-12
The Unsteady Shock-Boundary Layer Interaction in a Compressor Cascade—Part I: Measurements With Time-Resolved Particle Image Velocimetry
In the first part of this three-paper-series, time-resolved particle image velocimetry (TR-PIV) is performed in the transonic cascade to elucidate the shock-boundary layer interaction process and to provide comparative data for numerical studies and analysis in Parts II and III. The application of modern high-speed camera technology combined with a dual-pulse high-speed laser system enabled TR-PIV in the cascade for image areas covering ∼30% of the chord and ∼6% of the blade pitch at sampling intervals of 0.18 convective time units (CTUs) for the acquisition of multiple time sequences with duration of ∼2000 CTUs. The sampling rate is sufficient to resolve fluctuations of the separating region and accompanying movements of the shock system. To enable correlations between density variations of the shock system and velocity data, shadowgraphs are acquired synchronously with TR-PIV recordings at the same sampling rate. The TR-PIV and shadowgraph measurement setups, the image processing, and the resulting spatial resolutions are described in this part. An analysis of power spectral densities along near-wall rows in PIV data reveals the chord-wise spatial distribution of specific peaks and bands, which are also visible in the shock buffet spectrum. A spectral proper orthogonal decomposition (SPOD) of TR-PIV data is conducted to enable inspection of spatiotemporal modes of velocity fluctuations at specific broad peaks and tones in the buffet frequency range. Results indicate that upstream of the main shock, oblique shock waves occur at higher order harmonics of the fundamental buffet frequency and at specific high-frequency tones. The upstream propagation of disturbances beyond the excursion range of the main shock is demonstrated for the dominant buffet frequency as well as for the high-frequency tone and its first harmonic using cross-correlation maps. To locate possible sources of distinct tones at the entrance of the center passage, a SPOD of high-speed schlieren recordings is performed, capturing the shock systems in three passages. The results show that with these high-frequency tones, opposing vibrations of bow and lip shocks occur for neighboring blades.
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-12
The Unsteady Shock-Boundary Layer Interaction in a Compressor Cascade—Part I: Measurements With Time-Resolved Particle Image Velocimetry
In the first part of this three-paper-series, time-resolved particle image velocimetry (TR-PIV) is performed in the transonic cascade to elucidate the shock-boundary layer interaction process and to provide comparative data for numerical studies and analysis in Parts II and III. The application of modern high-speed camera technology combined with a dual-pulse high-speed laser system enabled TR-PIV in the cascade for image areas covering ∼30% of the chord and ∼6% of the blade pitch at sampling intervals of 0.18 convective time units (CTUs) for the acquisition of multiple time sequences with duration of ∼2000 CTUs. The sampling rate is sufficient to resolve fluctuations of the separating region and accompanying movements of the shock system. To enable correlations between density variations of the shock system and velocity data, shadowgraphs are acquired synchronously with TR-PIV recordings at the same sampling rate. The TR-PIV and shadowgraph measurement setups, the image processing, and the resulting spatial resolutions are described in this part. An analysis of power spectral densities along near-wall rows in PIV data reveals the chord-wise spatial distribution of specific peaks and bands, which are also visible in the shock buffet spectrum. A spectral proper orthogonal decomposition (SPOD) of TR-PIV data is conducted to enable inspection of spatiotemporal modes of velocity fluctuations at specific broad peaks and tones in the buffet frequency range. Results indicate that upstream of the main shock, oblique shock waves occur at higher order harmonics of the fundamental buffet frequency and at specific high-frequency tones. The upstream propagation of disturbances beyond the excursion range of the main shock is demonstrated for the dominant buffet frequency as well as for the high-frequency tone and its first harmonic using cross-correlation maps. To locate possible sources of distinct tones at the entrance of the center passage, a SPOD of high-speed schlieren recordings is performed, capturing the shock systems in three passages. The results show that with these high-frequency tones, opposing vibrations of bow and lip shocks occur for neighboring blades.
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-11
The Unsteady Shock–Boundary Layer Interaction in a Compressor Cascade—Part II: High-Fidelity Simulation
In the second part of this three-paper series, high-fidelity simulations of the transonic cascade TEAMAero at the aerodynamic design point with Rein=1.35×106 and Main=1.21 are presented. A high-order discontinuous Galerkin spectral element method with finite-volume subcell shock capturing is employed to simulate the flow based on an implicit large eddy simulation (LES) scheme and advanced over several buffeting cycles to reliably capture the shock unsteadiness. A study on the spanwise domain size shows that the shock oscillation amplitude decreases with increasing span, although its frequency and mean location remain fixed through the simulations. By comparing high- and low-resolution LES results, it is further presented that deviations from under-resolution are mostly limited to the separated region past the shock, where the high-fidelity results match experimental results more closely. In addition to the LES, low-fidelity unsteady Reynolds-averaged Navier–Stokes is shown to capture the shock unsteadiness correctly, but at a reduced amplitude and fails to match the force distributions on the blade surface. Through examination of instantaneous flow features, space–time relations and spectral proper orthogonal decomposition, a basic analysis of the shock–boundary layer interaction is presented and indicates that velocity perturbations travel upstream through the subsonic boundary layer and periodically cause oblique shock waves, transporting the information from the boundary layer into the passage.
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-11
The Unsteady Shock–Boundary Layer Interaction in a Compressor Cascade—Part II: High-Fidelity Simulation
In the second part of this three-paper series, high-fidelity simulations of the transonic cascade TEAMAero at the aerodynamic design point with Rein=1.35×106 and Main=1.21 are presented. A high-order discontinuous Galerkin spectral element method with finite-volume subcell shock capturing is employed to simulate the flow based on an implicit large eddy simulation (LES) scheme and advanced over several buffeting cycles to reliably capture the shock unsteadiness. A study on the spanwise domain size shows that the shock oscillation amplitude decreases with increasing span, although its frequency and mean location remain fixed through the simulations. By comparing high- and low-resolution LES results, it is further presented that deviations from under-resolution are mostly limited to the separated region past the shock, where the high-fidelity results match experimental results more closely. In addition to the LES, low-fidelity unsteady Reynolds-averaged Navier–Stokes is shown to capture the shock unsteadiness correctly, but at a reduced amplitude and fails to match the force distributions on the blade surface. Through examination of instantaneous flow features, space–time relations and spectral proper orthogonal decomposition, a basic analysis of the shock–boundary layer interaction is presented and indicates that velocity perturbations travel upstream through the subsonic boundary layer and periodically cause oblique shock waves, transporting the information from the boundary layer into the passage.
- Open Access
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-12
The Unsteady Shock-Boundary Layer Interaction in a Compressor Cascade—Part III: Mechanisms of Shock Oscillation
The shock-boundary layer interaction in transonic flows is known to cause strong unsteady flow effects that negatively affect the performance and operability of blade and cascade designs. Despite decades of research on the subject, little is still known about the physical mechanisms that drive the different oscillation frequencies observed with different designs. In the conclusion of this three-part series, the experimental and numerical data obtained with the Transonic Cascade TEAMAero are analyzed together in detail in order to test the main theories of continuous shock oscillation. This analysis exposes a main mechanism of shock oscillation, where pressure waves generated inside the passage of the cascade propagate upstream and interact strongly with the main shock when the latter is also in the passage. The interaction of these features causes a breakdown of the flow that is shown to propagate upstream, inevitably causing strong variations in the inflow angle and therefore on the operating conditions of the cascade. The high-frequency content of these pressure waves is also shown to be responsible for weaker high-frequency variations of the shock movement throughout the cycle. Parallels are also drawn with previous experimental campaigns in order to search for a global understanding of the different observations made. Although various parts of the described interaction are not fully understood yet, and the dataset of experimental measurements compiled is still rather small, a good basis is provided on which to further study the underlying mechanisms of unsteady flows in transonic cascades.
- 7 February 2025
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (9) , 1-12
Open AccessThe Unsteady Shock-Boundary Layer Interaction in a Compressor Cascade—Part III: Mechanisms of Shock Oscillation
The shock-boundary layer interaction in transonic flows is known to cause strong unsteady flow effects that negatively affect the performance and operability of blade and cascade designs. Despite decades of research on the subject, little is still known about the physical mechanisms that drive the different oscillation frequencies observed with different designs. In the conclusion of this three-part series, the experimental and numerical data obtained with the Transonic Cascade TEAMAero are analyzed together in detail in order to test the main theories of continuous shock oscillation. This analysis exposes a main mechanism of shock oscillation, where pressure waves generated inside the passage of the cascade propagate upstream and interact strongly with the main shock when the latter is also in the passage. The interaction of these features causes a breakdown of the flow that is shown to propagate upstream, inevitably causing strong variations in the inflow angle and therefore on the operating conditions of the cascade. The high-frequency content of these pressure waves is also shown to be responsible for weaker high-frequency variations of the shock movement throughout the cycle. Parallels are also drawn with previous experimental campaigns in order to search for a global understanding of the different observations made. Although various parts of the described interaction are not fully understood yet, and the dataset of experimental measurements compiled is still rather small, a good basis is provided on which to further study the underlying mechanisms of unsteady flows in transonic cascades.
- Open Access
- 13 November 2023
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 8 (4) , 47
The Current Gap between Design Optimization and Experiments for Transonic Compressor Blades
The successful design of compressor blades through numerical optimization relies on accurate CFD-RANS solvers that are able to capture the general performance of a given design candidate. However, this is a difficult task to achieve in transonic flow conditions, where the flow is dominated by inherently unsteady shock effects. In order to assess the current gap between numerics and experiments, the DLR has tested the recently optimized Transonic Cascade TEAMAero at the transonic cascade wind tunnel. The tests were performed at a Mach number of 1.2 and with inflow angles between 145 and 147°. The results indicate satisfactory agreement across the expected working range, over which the cascade losses were consistently predicted within a 3–6% error. However, some key differences are observed in the details of the wake and in the performance near the endpoints of the working range. This comparison helps validate the design process but also informs its constraints based on the limitations of CFD-RANS solvers.
- 13 November 2023
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 8 (4) , 47
Open AccessThe Current Gap between Design Optimization and Experiments for Transonic Compressor Blades
The successful design of compressor blades through numerical optimization relies on accurate CFD-RANS solvers that are able to capture the general performance of a given design candidate. However, this is a difficult task to achieve in transonic flow conditions, where the flow is dominated by inherently unsteady shock effects. In order to assess the current gap between numerics and experiments, the DLR has tested the recently optimized Transonic Cascade TEAMAero at the transonic cascade wind tunnel. The tests were performed at a Mach number of 1.2 and with inflow angles between 145 and 147°. The results indicate satisfactory agreement across the expected working range, over which the cascade losses were consistently predicted within a 3–6% error. However, some key differences are observed in the details of the wake and in the performance near the endpoints of the working range. This comparison helps validate the design process but also informs its constraints based on the limitations of CFD-RANS solvers.
- 3 April 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (8) , 1-23
The New Chapter of Transonic Compressor Cascade Design at the DLR
The design of compressor blades has been transformed by the advent of optimization algorithms, allowing designers to focus on finding the best optimization strategy for a desired application. However, transonic flow conditions on compressor blades still present considerable modeling challenges, even for a 2D blade section. This paper then focuses on the design of a new state-of-the-art compressor cascade for future test campaigns at the DLR’s Transonic Cascade Wind Tunnel (TGK). For this purpose, a review of the cascades previously tested at the TGK was performed to select a main reference with good efficiency at high loading. The data gathered also informed the optimization strategy applied with the DLR’s optimizer, AutoOpti. The process chain was evaluated with Reynolds Averaged Navier–Stokes CFD simulations using the DLR’s solver, TRACE. The optimization was set to minimize two objective functions: the first one focused on the efficiency at the design point, and the second one focused on the efficiency over the working range. The result is a Pareto front of cascades with a wide variety of design features with an efficiency improvement over the working range of about 24%. This improvement was achieved with a comparable aerodynamic loading. Further analyses were performed to select the “best” cascade for future test campaigns. The significant improvement obtained with respect to the reference and the wide variety of designs observed demonstrates that there is still much to be learned about blade design through optimization; even for 2D cascades and specially in transonic flow.
- 3 April 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (8) , 1-23
The New Chapter of Transonic Compressor Cascade Design at the DLR
The design of compressor blades has been transformed by the advent of optimization algorithms, allowing designers to focus on finding the best optimization strategy for a desired application. However, transonic flow conditions on compressor blades still present considerable modeling challenges, even for a 2D blade section. This paper then focuses on the design of a new state-of-the-art compressor cascade for future test campaigns at the DLR’s Transonic Cascade Wind Tunnel (TGK). For this purpose, a review of the cascades previously tested at the TGK was performed to select a main reference with good efficiency at high loading. The data gathered also informed the optimization strategy applied with the DLR’s optimizer, AutoOpti. The process chain was evaluated with Reynolds Averaged Navier–Stokes CFD simulations using the DLR’s solver, TRACE. The optimization was set to minimize two objective functions: the first one focused on the efficiency at the design point, and the second one focused on the efficiency over the working range. The result is a Pareto front of cascades with a wide variety of design features with an efficiency improvement over the working range of about 24%. This improvement was achieved with a comparable aerodynamic loading. Further analyses were performed to select the “best” cascade for future test campaigns. The significant improvement obtained with respect to the reference and the wide variety of designs observed demonstrates that there is still much to be learned about blade design through optimization; even for 2D cascades and specially in transonic flow.
- 13 June 2022
- Published by ASME International
The New Chapter of Transonic Compressor Cascade Design at the DLR
The approach to design compressor blades has been transformed over the years by the advent of efficient numerical optimization algorithms and increasing computing power. This has allowed designers to focus on finding the best optimization methodology for a desired application. However, transonic flow conditions on compressor blades still present considerable modeling and optimization challenges, making the optimization of even a 2D blade section a non-trivial undertaking. This paper then focuses on the design of a new state-of-the-art transonic compressor cascade for future wind tunnel test campaigns at the DLR. For this purpose, a thorough review was performed of similar cascades previously tested at the DLR’s Transonic Cascade Wind Tunnel. From this review, a main reference was picked corresponding to a modern cascade with notably good efficiency at high aerodynamic loading. The data gathered informed the definition of the optimization’s design strategy applied with the DLR’s in-house optimizer, AutoOpti. The process chain was evaluated with the DLR’s CFD solver for turbomachinery applications, TRACE, by performing RANS simulations with the k-ω SST turbulence model and γ-ReΘ transition model. The optimization was set to minimize two separate objective functions: the first one focused on the efficiency at the aerodynamic design point, while the second one was focused on the efficiency over the cascade’s working range. The result is a Pareto front of cascades with a wide variety of design characteristics and a considerable improvement in efficiency over the working range of about 24%. This improvement was achieved while maintaining a similar aerodynamic blade loading, quantified by a maximum increase of 3% of the de Haller number. Further post-optimization analyses were performed to select the “best” cascade for future wind tunnel test campaigns. The significant improvements obtained with respect to the reference and with a wide variety of cascade designs demonstrates that there is still much to be learned about blade design through optimization; even for 2D cascades and specially in transonic flow conditions.
- 13 June 2022
- Published by ASME International
The New Chapter of Transonic Compressor Cascade Design at the DLR
The approach to design compressor blades has been transformed over the years by the advent of efficient numerical optimization algorithms and increasing computing power. This has allowed designers to focus on finding the best optimization methodology for a desired application. However, transonic flow conditions on compressor blades still present considerable modeling and optimization challenges, making the optimization of even a 2D blade section a non-trivial undertaking. This paper then focuses on the design of a new state-of-the-art transonic compressor cascade for future wind tunnel test campaigns at the DLR. For this purpose, a thorough review was performed of similar cascades previously tested at the DLR’s Transonic Cascade Wind Tunnel. From this review, a main reference was picked corresponding to a modern cascade with notably good efficiency at high aerodynamic loading. The data gathered informed the definition of the optimization’s design strategy applied with the DLR’s in-house optimizer, AutoOpti. The process chain was evaluated with the DLR’s CFD solver for turbomachinery applications, TRACE, by performing RANS simulations with the k-ω SST turbulence model and γ-ReΘ transition model. The optimization was set to minimize two separate objective functions: the first one focused on the efficiency at the aerodynamic design point, while the second one was focused on the efficiency over the cascade’s working range. The result is a Pareto front of cascades with a wide variety of design characteristics and a considerable improvement in efficiency over the working range of about 24%. This improvement was achieved while maintaining a similar aerodynamic blade loading, quantified by a maximum increase of 3% of the de Haller number. Further post-optimization analyses were performed to select the “best” cascade for future wind tunnel test campaigns. The significant improvements obtained with respect to the reference and with a wide variety of cascade designs demonstrates that there is still much to be learned about blade design through optimization; even for 2D cascades and specially in transonic flow conditions.