Kurt R. VanDonselaar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kurt R. VanDonselaar has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Andrew B. Croll
Department of Physics and Materials and Nanotechnology Program North Dakota State University Fargo ND 58108 USA
2 shared publications - Dean C. Webster
Department of Coatings and Polymeric Materials North Dakota State University Fargo North Dakota USA
2 shared publications - Alfred J. Crosby
Department of Polymer Science and Engineering, University of Massachusetts Amherst, Amherst, MA 01003, USA
1 shared publication - Daniel Angel Bellido-Aguilar
Department of Coatings and Polymeric Materials, North Dakota State University 2 , Fargo, North Dakota 58102, USA
1 shared publication - David Boucher
Department of Coatings and Polymeric Materials, North Dakota State University, Fargo, North Dakota, 58108, USA
1 shared publication - Hyemin Kim
Polymer Science and Engineering Department, University of Massachusetts Amherst 3 , 120 Governors Drive, Amherst, Massachusetts 01002, USA
1 shared publication
Latest Publications
- Open Access
- 25 June 2026
- Published by Elsevier in Materials & Design
- Vol. 268
Predicting ice adhesion of fluid-containing elastomers from surface tension/energy and crosslink density
- 25 June 2026
- Published by Elsevier in Materials & Design
- Vol. 268
Open AccessPredicting ice adhesion of fluid-containing elastomers from surface tension/energy and crosslink density
- Open Access
- 13 November 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 159 (18)
Silicone elastomers and the Persson-Brener adhesion model
Many modern anti-icing and anti-fouling coatings rely on soft, low surface energy elastomeric materials such as polydimethylsiloxane for their functionality. While the low surface energy is desirable for reducing adhesion, very little work considers the larger contribution to adhesive failure caused by the viscoelastic nature of elastomers. Here we examine several different siloxane elastomers using a JKR adhesion test, which was operated over a range of different speeds and temperatures. Additionally, we characterize the dynamic mechanical modulus over a large range of frequencies for each material. We note that surface energies of the materials are all similar, but variation in adhesion strength is clear in the data. The variation at low speeds is related to elastomer architecture but the speed dependence itself is independent of architecture. Qualitative correlations are noted between the JKR adhesion measurements and the dynamic moduli. Finally, an attempt is made to directly compare moduli and adhesion through the recent Persson–Brener model. Approximations of the model are shown to be inaccurate. The full model is found to be accurate at low speeds, although it fails to precisely capture higher speed behaviour.
- 13 November 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 159 (18)
Open AccessSilicone elastomers and the Persson-Brener adhesion model
Many modern anti-icing and anti-fouling coatings rely on soft, low surface energy elastomeric materials such as polydimethylsiloxane for their functionality. While the low surface energy is desirable for reducing adhesion, very little work considers the larger contribution to adhesive failure caused by the viscoelastic nature of elastomers. Here we examine several different siloxane elastomers using a JKR adhesion test, which was operated over a range of different speeds and temperatures. Additionally, we characterize the dynamic mechanical modulus over a large range of frequencies for each material. We note that surface energies of the materials are all similar, but variation in adhesion strength is clear in the data. The variation at low speeds is related to elastomer architecture but the speed dependence itself is independent of architecture. Qualitative correlations are noted between the JKR adhesion measurements and the dynamic moduli. Finally, an attempt is made to directly compare moduli and adhesion through the recent Persson–Brener model. Approximations of the model are shown to be inaccurate. The full model is found to be accurate at low speeds, although it fails to precisely capture higher speed behaviour.