Baek‐Woon Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Baek‐Woon Lee has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Kyuha Chung
Cheil Industries Inc., 332‐2, Gocheon‐dong, Uiwasng‐Si, Gyeonggi‐do, 437‐711, S. KOREA
4 shared publicationsMunpyo Hong
LCD Business Unit, Samsung Electronics Corp., San 24, Nongseo‐dong, Giheung‐gu, Yongin‐si, 449‐711, S. KOREA
3 shared publicationsChangyong Kim
Samsung Advanced Institute of Technology, San 14‐1, Nongseo‐ri, Giheung‐eup, Yongin‐si, 449‐712, S. KOREA
2 shared publicationsCheolwoo Park
AMLCD Div., Samsung Electronics Corp., San 24, Nongseo‐ri, Giheung‐eup, Yongin‐si, 449‐711, S. KOREA
2 shared publicationsHae‐Yeon Lee
Samsung Mobile Display, San 24, Nongseo‐dong, Giheung‐gu, Yongin‐Si, Gyeonggi‐do, 449‐711, S. KOREA
2 shared publicationsJeongye Choi
AMLCD Div., Samsung Electronics Corp., San 24, Nongseo‐ri, Giheung‐eup, Yongin‐si, 449‐711, S. KOREA
2 shared publications
Latest Publications
- 1 June 2009
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 40 (1) , 1752-1755
P‐196L: Late‐News Poster : Micro‐Cavity Design of RGBW AMOLED for Wide Color Gamut and Low Color Shift
Previously, we reported two optical structures for bottom‐emitting white OLED, exhibiting wide color gamut (> 100% NTSC) and high (> 40%) transmission through color filter. The panels employed RGBW color system for efficiency. The color shifts at oblique angles for the individual R, G, B, and R+G+B were maintained below Δu'v' < 0.02@ 60°. However, the colors produced by the combination of R/G/B subpixels and W subpixels exhibit large color shift when viewed at oblique angles because the luminance profiles, as a function of viewing angle, of the R/G/B which employ strong resonance, and the W which has weak resonance, are very different. In this report, we present a novel optical architecture for the W‐subpixel. The color shift for the W‐ subpixel was reduced from Δu'v' = 0.059 to 0.026 and the luminance profile was much closer to those of R/G/B subpixels. The efficiency of the W‐subpixel with the new structure was on the same level as that of the conventional, plain, weak‐resonance structure.
- 1 June 2009
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 40 (1) , 1752-1755
P‐196L: Late‐News Poster : Micro‐Cavity Design of RGBW AMOLED for Wide Color Gamut and Low Color Shift
Previously, we reported two optical structures for bottom‐emitting white OLED, exhibiting wide color gamut (> 100% NTSC) and high (> 40%) transmission through color filter. The panels employed RGBW color system for efficiency. The color shifts at oblique angles for the individual R, G, B, and R+G+B were maintained below Δu'v' < 0.02@ 60°. However, the colors produced by the combination of R/G/B subpixels and W subpixels exhibit large color shift when viewed at oblique angles because the luminance profiles, as a function of viewing angle, of the R/G/B which employ strong resonance, and the W which has weak resonance, are very different. In this report, we present a novel optical architecture for the W‐subpixel. The color shift for the W‐ subpixel was reduced from Δu'v' = 0.059 to 0.026 and the luminance profile was much closer to those of R/G/B subpixels. The efficiency of the W‐subpixel with the new structure was on the same level as that of the conventional, plain, weak‐resonance structure.
- 1 May 2008
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 39 (1) , 1050-1053
68.4: Micro‐cavity Design of RGBW AMOLED for 100% Color Gamut
We report two optical structures for bottom‐emitting white OLED. We employed RGBW color system because of its high efficiency. for RGB‐subpixels, the cavity resonance was enhanced by dielectric mirror, and for W‐subpixel, the mirror was removed. Optical lengths were controlled by two different methods: by the thickness of dielectric filler on top of the mirror or by the angle of oblique emission. with both methods, we were able to fabricate AMOLEDs that exhibited color gamut exceeding 100% NTSC. More importantly, the transmission of white OLED through R/G/B color filters was significantly higher (up to 50%) than that of the conventional structure employing no mirror, even though the color gamut increased from ∼75% to ∼100%.
- 1 May 2008
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 39 (1) , 1050-1053
68.4: Micro‐cavity Design of RGBW AMOLED for 100% Color Gamut
We report two optical structures for bottom‐emitting white OLED. We employed RGBW color system because of its high efficiency. for RGB‐subpixels, the cavity resonance was enhanced by dielectric mirror, and for W‐subpixel, the mirror was removed. Optical lengths were controlled by two different methods: by the thickness of dielectric filler on top of the mirror or by the angle of oblique emission. with both methods, we were able to fabricate AMOLEDs that exhibited color gamut exceeding 100% NTSC. More importantly, the transmission of white OLED through R/G/B color filters was significantly higher (up to 50%) than that of the conventional structure employing no mirror, even though the color gamut increased from ∼75% to ∼100%.
- 1 May 2007
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 38 (1) , 1386-1389
L‐2: Late‐News Paper : The RGBW Advantage for AMOLED
The combination of white OLED and color filter (CF) is the most mature solution for making large‐area AMOLEDs. The system can benefit from introducing a white subpixel. We compared the power efficiencies of RGB and RGBW system. As a basis for the comparison, we also propose a reference video called FC in which every color point in the cubic RGB space has the equal probability of appearance. We found that the RGBW system has 16.7% lower power consumption and 23% lower current stress (thus longer lifetime) for the reference video. We also analyzed various kinds of videos from DVD movies, HDTVs and IT graphics to find that in these actual video materials, there is much more utilization of white so that the power consumption is roughly a half of that for the FC video. The reduction is so significant that the W OLED + RGBW CF system has 60% lower power consumption than the RGB CF system and only 50% higher power consumption than the RGB OLED (no CF).
- 1 May 2007
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 38 (1) , 1386-1389
L‐2: Late‐News Paper : The RGBW Advantage for AMOLED
The combination of white OLED and color filter (CF) is the most mature solution for making large‐area AMOLEDs. The system can benefit from introducing a white subpixel. We compared the power efficiencies of RGB and RGBW system. As a basis for the comparison, we also propose a reference video called FC in which every color point in the cubic RGB space has the equal probability of appearance. We found that the RGBW system has 16.7% lower power consumption and 23% lower current stress (thus longer lifetime) for the reference video. We also analyzed various kinds of videos from DVD movies, HDTVs and IT graphics to find that in these actual video materials, there is much more utilization of white so that the power consumption is roughly a half of that for the FC video. The reduction is so significant that the W OLED + RGBW CF system has 60% lower power consumption than the RGB CF system and only 50% higher power consumption than the RGB OLED (no CF).
- 1 June 2006
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 37 (1) , 1801-1803
60.3: Spatio‐Temporal Edge Enhancement for Reducing Motion Blur
LCDs suffer from a loss of resolution when displaying moving images (motion blur). Solutions to this problem have included overdriving and reduction of temporal aperture by introducing blanks or by increasing the frame rate. These methods usually require additional hardware, thereby increasing cost. We propose a purely mathematical operation to reduce motion blur. In the proposed method, the degree of overdriving is not constant over the whole image. Rather, it depends on the spatial complexity surrounding a given area, wherein more overdriving is applied to areas of high spatial frequency. In this way, motion blur can be reduced without inducing artifacts which may otherwise result from excessive overdriving. The new method shows easily distinguishable improvement and the MPRT (Motion Picture Response Time) values are reduced by 5 ∼ 10%.
- 1 June 2006
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 37 (1) , 1801-1803
60.3: Spatio‐Temporal Edge Enhancement for Reducing Motion Blur
LCDs suffer from a loss of resolution when displaying moving images (motion blur). Solutions to this problem have included overdriving and reduction of temporal aperture by introducing blanks or by increasing the frame rate. These methods usually require additional hardware, thereby increasing cost. We propose a purely mathematical operation to reduce motion blur. In the proposed method, the degree of overdriving is not constant over the whole image. Rather, it depends on the spatial complexity surrounding a given area, wherein more overdriving is applied to areas of high spatial frequency. In this way, motion blur can be reduced without inducing artifacts which may otherwise result from excessive overdriving. The new method shows easily distinguishable improvement and the MPRT (Motion Picture Response Time) values are reduced by 5 ∼ 10%.
- 1 May 2005
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 36 (1) , 1583-1585
51.2: Mastering the Moving Image: Refreshing TFT‐LCDs at 120 Hz
Moving image quality has been the Achilles' heel of TFT‐LCDs. The switching speed of liquid crystals has been improved constantly, so that we now have reached to a point where further improvement does not translate into real image quality gain: LCDs are facing the final hurdle as a hold‐type display. Two ways were proposed to overcome the problem. One is to introduce impulsive transmission and the other is to increase the refresh rate. The first approach was commercialized, with limited success. The second approach has been emulated with a high refresh‐rate CRT. For the first time, we report a 40″ LCD‐TV refreshed at 120 Hz. The higher refresh rate led to 25% reduction in the on + off response time and 50% reduction in the intergray response time. There was substantial video quality improvement as well as the nominal enhancement: images sweeping the whole screen horizontally in two seconds showed little deterioration in details.
- 1 May 2005
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 36 (1) , 1583-1585
51.2: Mastering the Moving Image: Refreshing TFT‐LCDs at 120 Hz
Moving image quality has been the Achilles' heel of TFT‐LCDs. The switching speed of liquid crystals has been improved constantly, so that we now have reached to a point where further improvement does not translate into real image quality gain: LCDs are facing the final hurdle as a hold‐type display. Two ways were proposed to overcome the problem. One is to introduce impulsive transmission and the other is to increase the refresh rate. The first approach was commercialized, with limited success. The second approach has been emulated with a high refresh‐rate CRT. For the first time, we report a 40″ LCD‐TV refreshed at 120 Hz. The higher refresh rate led to 25% reduction in the on + off response time and 50% reduction in the intergray response time. There was substantial video quality improvement as well as the nominal enhancement: images sweeping the whole screen horizontally in two seconds showed little deterioration in details.
- 1 May 2004
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 35 (1) , 111-113
9.2: Implementation of RGBW Color System in TFT‐LCDs
Last year, we introduced a TFT‐LCD with RGBW color system. The primary advantage of the RGBW system is that its optical efficiency is at least 50% higher than the RGB system. However, it is not a simple task to incorporate the new color system into the existing infrastructure of the RGB system: the driving circuitry, fabrication of color filter, and color conversion. In this report, the practical hurdles are discussed and the solutions are presented.
- 1 May 2004
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 35 (1) , 111-113
9.2: Implementation of RGBW Color System in TFT‐LCDs
Last year, we introduced a TFT‐LCD with RGBW color system. The primary advantage of the RGBW system is that its optical efficiency is at least 50% higher than the RGB system. However, it is not a simple task to incorporate the new color system into the existing infrastructure of the RGB system: the driving circuitry, fabrication of color filter, and color conversion. In this report, the practical hurdles are discussed and the solutions are presented.
- 1 May 2003
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 34 (1) , 1212-1215
40.5L: Late‐News Paper: TFT‐LCD with RGBW Color System
Although LCDs are widely used in power‐consumption critical applications, they are not very energy‐efficient. The largest absorber of light is the color filter. We developed a TFT‐LCD with four‐color subpixels: red, green, blue and white. The addition of the white subpixel greatly enhanced the light efficiency: up by 50%. The RGB‐to‐RGBW mapping algorithm was designed so that the hue and saturation remains unchanged from the original color. The result is a very bright display with color characteristic almost identical to RGB LCDs.
- 1 May 2003
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 34 (1) , 1212-1215
40.5L: Late‐News Paper: TFT‐LCD with RGBW Color System
Although LCDs are widely used in power‐consumption critical applications, they are not very energy‐efficient. The largest absorber of light is the color filter. We developed a TFT‐LCD with four‐color subpixels: red, green, blue and white. The addition of the white subpixel greatly enhanced the light efficiency: up by 50%. The RGB‐to‐RGBW mapping algorithm was designed so that the hue and saturation remains unchanged from the original color. The result is a very bright display with color characteristic almost identical to RGB LCDs.