Camila da Silva Martinatto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Camila da Silva Martinatto has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Giovani Jordi Bruschi
Graduate Program in Environmental Science and Technology, Federal University of Fronteira Sul, Erechim 99700-970, Brazil
3 shared publications - Nilo Cesar Consoli
Universidade Federal do Rio Grande do Sul
3 shared publications - Carolina Pereira dos Santos
Universidade Federal Do Rio Grande Do Sul, (Graduate Program in Civil Engineering), Porto Alegre, Brazil
2 shared publications - João Paulo de Sousa Silva
Exploration and Mineral Projects – Mineral Development Centre, VALE S.A, Santa Luzia, Brazil
2 shared publications - Luana Rutz Schulz
Ph.D. Candidate, Graduate Program of Civil Engineering, Federal Univ. of Rio Grande do Sul, Porto Alegre 90035-190, Brazil. ORCID:
2 shared publications - Aghileh Khajeh
Universidade Federal Do Rio Grande Do Sul, (Graduate Program in Civil Engineering), Porto Alegre, Brazil
1 shared publication
Latest Publications
- 9 July 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (6) , 1-18
Hydromechanical Behavior of Cement-Stabilized Iron Ore Tailings
- 9 July 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (6) , 1-18
Hydromechanical Behavior of Cement-Stabilized Iron Ore Tailings
- Open Access
Mechanical and Microstructural Response of Iron Ore Tailings under Low and High Pressures Considering a Wide Range of Molding Characteristics
The dry stacking of filtered tailings is an option to deal with safety-related issues involving traditional slurry disposition in impoundments. Filtered tailings can be compacted to pre-define design specifications, which minimizes structural instability problems, such as those related to liquefaction. Yet, comprehending the tailing’s response under various stress states is essential to designing any dry stacking facility properly. Thus, the present research evaluated the mechanical response of cemented and uncemented compacted filtered iron ore tailings, considering different molding characteristics related to compaction degree and molding moisture content. Therefore, a series of one-dimensional compression tests and consolidated isotropically drained triaxial tests (CID), using 300 kPa and 3000 kPa effective confining pressures, were carried out for different specimens compacted at various molding characteristics. In addition, changes in gradation owing to both compression and shearing were evaluated using sedimentation with scanning electron microscope tests. The overall results have indicated that the 3% Portland cement addition enhanced the strength and stiffness of the compacted iron ore tailings, considering the lower confining pressure. Nevertheless, the same was not evidenced for the higher confining stress. Moreover, the dry-side molded specimens were initially stiffer, and significant particle breakage did not occur owing to one-dimensional compression but only due to shearing (triaxial condition).
Open AccessMechanical and Microstructural Response of Iron Ore Tailings under Low and High Pressures Considering a Wide Range of Molding Characteristics
The dry stacking of filtered tailings is an option to deal with safety-related issues involving traditional slurry disposition in impoundments. Filtered tailings can be compacted to pre-define design specifications, which minimizes structural instability problems, such as those related to liquefaction. Yet, comprehending the tailing’s response under various stress states is essential to designing any dry stacking facility properly. Thus, the present research evaluated the mechanical response of cemented and uncemented compacted filtered iron ore tailings, considering different molding characteristics related to compaction degree and molding moisture content. Therefore, a series of one-dimensional compression tests and consolidated isotropically drained triaxial tests (CID), using 300 kPa and 3000 kPa effective confining pressures, were carried out for different specimens compacted at various molding characteristics. In addition, changes in gradation owing to both compression and shearing were evaluated using sedimentation with scanning electron microscope tests. The overall results have indicated that the 3% Portland cement addition enhanced the strength and stiffness of the compacted iron ore tailings, considering the lower confining pressure. Nevertheless, the same was not evidenced for the higher confining stress. Moreover, the dry-side molded specimens were initially stiffer, and significant particle breakage did not occur owing to one-dimensional compression but only due to shearing (triaxial condition).
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Moisture Content as a Key Parameter Influencing the Strength Development of Alkali-Activated Sand
Alternative materials to ordinary Portland cement (OPC), with lower environmental impacts and similar mechanical performance, are growing in interest of geotechnical techniques, such as soil stabilization. The present study evaluates the alkali activation of a system composed of ceramic wastes, carbide lime and sodium hydroxide solution as a green stabilization for granular soil. To analyze the performance of the alkali-activated cement (AAC), mechanical tests were carried out based on unconfined compression strength and split tensile strength due design mix focusing on different water content, precursor combinations and time of curing. The results have shown an enhanced in mechanical response, but in specific samples the additional water to achieve the molding moisture weakens the solution, reducing strength. The correlation of the mechanical parameters with the porosity by volumetric content of binder index (η/Biv) was an appropriate parameter for evaluating stabilization for granular soil.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessMoisture Content as a Key Parameter Influencing the Strength Development of Alkali-Activated Sand
Alternative materials to ordinary Portland cement (OPC), with lower environmental impacts and similar mechanical performance, are growing in interest of geotechnical techniques, such as soil stabilization. The present study evaluates the alkali activation of a system composed of ceramic wastes, carbide lime and sodium hydroxide solution as a green stabilization for granular soil. To analyze the performance of the alkali-activated cement (AAC), mechanical tests were carried out based on unconfined compression strength and split tensile strength due design mix focusing on different water content, precursor combinations and time of curing. The results have shown an enhanced in mechanical response, but in specific samples the additional water to achieve the molding moisture weakens the solution, reducing strength. The correlation of the mechanical parameters with the porosity by volumetric content of binder index (η/Biv) was an appropriate parameter for evaluating stabilization for granular soil.