Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Christian Enrique Nava-Alcantar has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Body Mass Index on Dynamic Plantar Pressure, Spatiotemporal Parameters, and Gait Symmetry

    by Christian Enrique Nava-Alcantar, Israel Miguel-Andrés, Marco Antonio Martínez-Bocanegra, Agustín Vidal-Lesso, Jorge Armando Ramos-Frutos, Israel Aguilera-Navarrete, Luis Ángel Ortiz-Lango

    Background/Objectives: Previous studies have shown that excess body weight influences plantar pressure. However, the specific impact of Body Mass Index (BMI) on dynamic pressure distribution during different phases of walking, as well as its effect on load symmetry between the feet, requires further investigation. This study aimed to evaluate the effects of varying BMI categories on dynamic plantar pressure, spatiotemporal gait parameters, and load symmetry. Methods: A retrospective analysis of pre-existing records from 300 adults (2017–2025) classified as normal weight, overweight, and obese was conducted. Dynamic plantar pressure, contact time, and gait speed across four stance phases were assessed using baropodometric platforms. Bilateral differences were evaluated via the symmetry index (SI). Results: Overweight and obese individuals exhibited higher plantar pressures and prolonged contact times, particularly during the forefoot contact phase (FFCP) (p < 0.001). Gait speed decreased inversely with BMI across all phases. Despite these kinematic adaptations, BMI-related load asymmetry occurred only during the initial contact phase (ICP) (p < 0.001), restoring stability in subsequent phases. Conclusions: Excess body mass is associated with targeted mechanical overload of the forefoot rather than uniform stress across the foot. To manage inertia and maintain symmetry, individuals with high BMI may adopt spatiotemporal strategies that reduce speed and extend double support, potentially prioritizing stability over propulsive efficiency. These findings suggest that orthotic interventions for individuals with high BMI may benefit from prioritizing forefoot offloading, although prospective studies are needed.

  • Current methods and criteria for defining foot symmetry in biomechanical, clinical, and anthropometric assessments: A systematic review

    by Christian Enrique Nava-Alcantar, Israel Miguel-Andrés, Jorge Armando Ramos-Frutos, Agustín Vidal-Lesso, Javier Cruz-Salgado, Sergio Alonso-Romero


  • Open Access

    Structural analysis of generative design applied to ergonomic plantar orthoses

    by Christian Enrique Nava-Alcantar, Agustín Vidal-Lesso, Marco Antonio Martínez-Bocanegra, Luis Ángel Ortiz-Lango, Juan Carlos García-Valadez, Sergio Alonso-Romero, Israel Miguel-Andres

    Plantar orthoses are devices designed to provide support and correct the biomechanics of the foot. Generative design offers ample potential for personalization; however, the analysis of its structural behavior continues to be a significant challenge. This research aims to evaluate the structural optimization of orthoses designed by generative design compared to traditional models. An analysis of 33 middle-aged adult men classified as normal weight, with an average weight of 65.32 ± 6.79 kg, was performed using a baropodometric database. An optimized orthosis was designed by parametric modeling to evaluate its mechanical response in static standing conditions, using the finite element method with the TPU A95 material. The results indicated that the trabecular structures produced by generative design absorb more energy (0.3876 J) than a bilaminated orthosis made with EVA A40 and A15 materials (0.0362 J). The levels of deformation obtained (maximum principal strain = 1.34%, equivalent elastic strain = 2.14%) indicate that the composition of the generative model works well within the elastic regime, ensuring structural integrity. However, the low strain and strain energy values suggest relatively rigid behavior, which can limit the shock absorption capacity. The main contribution of this work is to demonstrate how generative design can be integrated into methodologies for designing plantar orthotics. It explores the potential benefits of this approach and examines how generative design parameters influence mechanical responses. This research provides a technical foundation for optimizing ergonomic orthoses through generative design and structural modeling. The findings emphasize the potential of generative design in creating optimized orthoses and highlight the significance of design parameters on the outcomes achieved. This insight is valuable for future applications of generative design in the field of ergonomics.

  • Open Access

    Geometric accuracy analysis in mesh-to-solid conversion for 3D anatomical models through Taguchi methodology

    by Christian Enrique Nava-Alcantar, Israel Miguel-Andres, Jorge Armando Ramos-Frutos, Didier Samayoa-Ochoa, Javier Cruz-Salgado, Agustín Vidal-Lesso, Marco Antonio Martínez-Bocanegra

    Three-dimensional reconstruction of anatomical models from clinical data faces challenges in maintaining geometric fidelityduring the conversion of surface models to parametric solids. Mesh processing techniques, such as smoothing, remeshing,and polygon reduction, aim to optimize mesh quality but can lead to loss of geometric information. A methodology wasdeveloped to process 3D surface meshes and convert them into solids from both faceted and organic geometries. Theimpact of different processing parameters on mesh topology and post-conversion geometry was evaluated using theTaguchi methodology with an L16 orthogonal design, analyzing three factors: smooth factor, remesh, and polygon reductionpercentage. The smooth factor had the most significant influence (p < 0.01), followed by remesh (p < 0.05), while polygonreduction was not statistically significant (p > 0.05). Conversion techniques produced significant differences (p = 0.0012),with faceted geometries yielding results closer to the target. Geometric deviation analysis using bidirectional Hausdorffdistance demonstrated sub-millimetric discrepancies in all cases. Faceted models showed RMS values between 0.067 and0.183 mm while organic models ranged from 0.076 to 0.225 mm with minimal deviation. Volumetric analysis revealedmoderate reductions averaging 4.53 ± 2.88% for faceted and 4.98 ± 3.07% for organic geometries without volumetricexpansion. Despite slightly higher sensitivity in organic models, deviations remained within acceptable tolerances foranatomical reconstruction and computational biomechanics, indicating preserved morphological fidelity after processing

  • Open Access

    Investigation of pressure map distribution for the design of an ergonomic cushion through computer-aided engineering

    by Luis Fernando de Jesús Barajas Patlán, Jorge Armando Ramos Frutos, Israel Miguel-Andres, Christian Enrique Nava Alcantar

    Prolonged occupational sedentary behavior is associated with musculoskeletal disorders and pressure ulcers, consequently diminishing quality of life and productivity. Current ergonomic cushions frequently lack a design foundation grounded in user-specific pressure data. This study developed and validated a methodology for optimizing such cushions, reversing the traditional approach by utilizing pressure mapping analysis as the initial stage. Pressure maps in a sitting position (flat surface, three postures) were characterized for 40 males (age: 25.25 ± 4.00 years; Body Mass Index: 23.83 ± 3.93 kg/m²) using a CONFORMat® software. The average pressure (12.67 ± 4.17 kPa, 12.93 ± 4.31 kPa, and 12.00 ± 3.62 kPa for the three postures, respectively) exhibited no significant variations between postures (Kruskal-Wallis, p > 0.05). These data served as the foundation for the design, which integrated Taguchi method optimization (varying geometry, thickness, and material) and the prediction of mechanical behavior through finite element analysis. The methodology resulted in a cushion design (square, viscoelastic foam) that, validated by simulation and experimental prototypes, demonstrated a more uniform pressure distribution, a reduction in average pressure, an increased contact area, and a preference expressed by the experimental group. The primary contribution lies in the proposal and validation of a methodological workflow that prioritizes pressure map analysis to inform ergonomic design, thereby offering a systematic approach to enhance the effectiveness of cushions and mitigate the adverse effects of sedentary behavior.


  • Open Access

    Diseño generativo aplicado en el diseño de un pedal de frenado para automóvil

    by Christian Enrique Nava Alcantar, Luis Armando Puente Gallardo, Marco Antonio Martinez Bocanegra, Mariano Braulio Sánchez

    El presente trabajo propone el uso de diseño generativo para el modelado de un pedal de freno de un automóvil, generando una propuesta de diseño funcional, segura y ligera; reduciendo lo más posible la cantidad de material, pero manteniendo una buena resistencia mecánica. Para esta investigación, se hizo uso del módulo de diseño generativo del software CAD Autodesk Fusion 360®. Este software emplea una serie de algoritmos y los parámetros definidos por el usuario, y en base a ello, generar una serie de propuestas de diseño del pedal. Como resultados de la investigación, se obtuvieron dos propuestas del pedal de frenado. El análisis por elementos finitos (FEM) mostro esfuerzos mecánicos de hasta un 86.07% por debajo del esfuerzo último del material de fabricación (aluminio 6061-T4). Adicionalmente, se obtuvo un factor de seguridad de hasta 4.8, con una reducción de la masa del pedal de hasta 16.67%. Los resultados mostraron que diseño generativo es una buena herramienta para explorar nuevas ideas y conceptos que fomentan la innovación en el diseño automotriz, logrando diseños funcionales, resistentes y con bajo consumo de material.