Yuankun Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yuankun Zheng has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Donghong Zhang
School of Agricultural Engineering and Food Science, Shandong University of Technology
1 shared publication- Dongliang Gan
School of Automation and Electrical Engineering, Lanzhou Jiaotong University, Lanzhou, China
1 shared publication - Hang Xu
School of Microelectronics, Fudan University, Shanghai 200433, China
1 shared publication - Hang Zhou
School of Electrical Engineering and Automation, Wuhan University, Wuhan 430072, China
1 shared publication - Hongzhen Cai
Shandong Research Center of Engineering and Technology for Clean Energy, Zibo 255000, China
1 shared publication - Jiajun Mei
Huaneng Jiangsu Clean Energy Branch, Nanjing, Jiangsu, China
1 shared publication
Latest Publications
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (6) , 4410-4421
Independent Fast Phase Shifting Transformer: A Flexible and High-Precision Power Flow Controller
With the increasing proportion of renewable energy sources in modern power systems, the power flow problem has become more prominent. The traditional phase shift transformer (PST) has the advantages of simple structure, high reliability, and low cost. However, PST can only regulate the active power flow of the line by controlling the phase shift angle, and cannot independently regulate the voltage amplitude of the line. In addition, its slow response speed and low regulation accuracy cannot meet the requirements of the new power system for power flow control. Therefore, a novel type of independent fast phase shifting transformer (IF-PST) is proposed. IF-PST has two independent regulating windings. One is on the power side and the other is on the load side. IF-PST can independently regulate the line voltage and active power with higher regulation accuracy than PST. In addition, IF-PST uses power electronic on-load tap changer for tap switching, improving response speed. Firstly, the working principle of IF-PST is introduced, and the independent regulation characteristics are elaborated. Then, the IF-PST winding turns and parameter design method are studied. Correspondingly, a tap selection method and control strategy are developed for IF-PST. On the basis of theoretical analysis, simulation and experimental testing are conducted, and the simulation and experimental results verified the rationality and practicality of IF-PST.
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 38 (6) , 4410-4421
Independent Fast Phase Shifting Transformer: A Flexible and High-Precision Power Flow Controller
With the increasing proportion of renewable energy sources in modern power systems, the power flow problem has become more prominent. The traditional phase shift transformer (PST) has the advantages of simple structure, high reliability, and low cost. However, PST can only regulate the active power flow of the line by controlling the phase shift angle, and cannot independently regulate the voltage amplitude of the line. In addition, its slow response speed and low regulation accuracy cannot meet the requirements of the new power system for power flow control. Therefore, a novel type of independent fast phase shifting transformer (IF-PST) is proposed. IF-PST has two independent regulating windings. One is on the power side and the other is on the load side. IF-PST can independently regulate the line voltage and active power with higher regulation accuracy than PST. In addition, IF-PST uses power electronic on-load tap changer for tap switching, improving response speed. Firstly, the working principle of IF-PST is introduced, and the independent regulation characteristics are elaborated. Then, the IF-PST winding turns and parameter design method are studied. Correspondingly, a tap selection method and control strategy are developed for IF-PST. On the basis of theoretical analysis, simulation and experimental testing are conducted, and the simulation and experimental results verified the rationality and practicality of IF-PST.
- Open Access
- 3 December 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 557-573
Effect of moisture content during preparation on the physicochemical properties of pellets made from different biomass materials
The influence of moisture content was investigated relative to the pellet forming process and the pellet properties. Three different types of raw biomass (pine sawdust, corn straw, and peanut shell) were pelletized by hot pressing at different moisture levels (12%, 14%, and 16%) in a pellet mill with horizontal and ring type dies to investigate its physical property indexes of durability, pellet density, and combustion performance. The results of the study showed that pellet density and heating value were related to the moisture content. The maximum pellet density of the fuel pellets of sawdust, corn straw, and peanut shells was 1180 kg/m3, 1220 kg/m3, and 1130 kg/m3, respectively. The drop resistance and deformation resistance of pine sawdust and corn straw decreased with increased moisture content, but peanut shell initially increased with the increase of moisture before decreasing. The comprehensive combustion index of corn straw (14.03) was the highest during the combustion performance analysis in comparison to sawdust (11.10) and peanut shell (10.00). Overall, the optimal moisture content of sawdust, corn straw, and peanut shell was 12%, 12%, and 14%, respectively, and the combustion performance of the pellets made from corn straw was superior compared to the other two feedstocks.
- 3 December 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 557-573
Open AccessEffect of moisture content during preparation on the physicochemical properties of pellets made from different biomass materials
The influence of moisture content was investigated relative to the pellet forming process and the pellet properties. Three different types of raw biomass (pine sawdust, corn straw, and peanut shell) were pelletized by hot pressing at different moisture levels (12%, 14%, and 16%) in a pellet mill with horizontal and ring type dies to investigate its physical property indexes of durability, pellet density, and combustion performance. The results of the study showed that pellet density and heating value were related to the moisture content. The maximum pellet density of the fuel pellets of sawdust, corn straw, and peanut shells was 1180 kg/m3, 1220 kg/m3, and 1130 kg/m3, respectively. The drop resistance and deformation resistance of pine sawdust and corn straw decreased with increased moisture content, but peanut shell initially increased with the increase of moisture before decreasing. The comprehensive combustion index of corn straw (14.03) was the highest during the combustion performance analysis in comparison to sawdust (11.10) and peanut shell (10.00). Overall, the optimal moisture content of sawdust, corn straw, and peanut shell was 12%, 12%, and 14%, respectively, and the combustion performance of the pellets made from corn straw was superior compared to the other two feedstocks.