JTJinchen Tang

Jinchen Tang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jinchen Tang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Resin-AgI Dot Pattern Surfaces for Ordered Frost Growth and Low-Adhesion Defrosting

    by Qun Dang, Takao Okabe, Jinchen Tang, Katsuhiko Nishimura, Gao Yao, Lizhen Huang, Jiaming Gong, Anna Sciazko, Koki Munekiyo, Ryosuke Matsumoto, et al.

    Frost accumulation degrades the performances of various energy and transportation devices. However, frost removal by controlling its morphology remains underexplored. Here, we report a photolithographically fabricated resin-AgI dot pattern (RADP) surface that enables deterministic control of ice nucleation and frost morphology. Owing to crystallographic matching between AgI and ice Ih, water vapor preferentially nucleates on patterned AgI dots, forming highly ordered, flower-shaped frost crystals with inclined growth orientations. Three-dimensional reconstructions by replica method reveal that the root density and mass per unit subtract area of frost on RADP surface are reduced to 3.10% and 20.2% of those on bare resin, respectively. Molecular dynamics simulations reveal that ice nucleation initiates on AgI basal facets and that the initial alignment of crystal orientation is governed by epitaxial matching. By optimizing AgI dot diameter and pitch, mechanically fragile frost roots are achieved at wall temperature of -15 °C and air temperature of 20 °C with relative humidity of 30%, enabling spontaneous detachment and efficient airflow-assisted defrosting. This work establishes a structure-guided strategy for scalable and energy-efficient frost management.

  • Open Access

    Frost Growth Modes on Surfaces with Synergistic Effects of Wettability and Ice Nucleation Agent

    by Qun Dang, Takao Okabe, Jinchen Tang, Katsuhiko Nishimura, Anna Sciazko, Naoki Shikazono

    De-frosting strategies are essential to address the challenges posed by frost accumulation in both natural and industrial settings. However, little attention has been given to optimize defrosting performance by controlling the morphology of frost crystals. In this study, we investigate frost formation on four surfaces by resin and AgI particles. Using a replica method, the three-dimensional frost structures are reconstructed and compared with the frost structure formed on a smooth silicon surface as a reference. To elucidate the observed morphological differences, molecular dynamics simulations are performed. Results show that the frost on the resin surface embedded with AgI particles has a compact, faceted and continuous ice structure, attributed to its monocrystalline growth. Notably, the root density of the frost on this surface is only 18.3% of that on the silicon surface, while the supported mass per unit projected area reaches 4.07 g/cm² at duration of 30 mins, which is 36.5% of silicon. This structure enables weak interfacial adhesion and easy mechanical removal. This work presents a novel strategy for energy-efficient defrosting by tailoring crystal nucleation and growth. The approach holds potential for application in refrigeration systems, aerospace components, and cold-chain logistics, etc.

  • Open Access

    Frost growth and 3D reconstruction on silver iodide (AgI) dot-patterned surface under desublimation conditions

    by Jinchen Tang, Takao Okabe, Katsuhiko Nishimura, Naoki Shikazono

    This study investigates the frost growth behaviors on a silver iodide (AgI) dot-patterned surface under desublimation conditions. The surface was fabricated using a two-step process combining UV lithography and UV nanoimprinting, resulting in a flat substrate with AgI dots embedded in a UV-curable resin (X433). The main objectives were to capture 3D frost morphologies through replica method and to evaluate whether such localized nucleation sites can induce laterally confined frost growth as observed in previous studies using AgI stripe patterns. Experiments were conducted at ambient temperatures of 2 ℃ and 10 ℃ with 40% relative humidity. Surface temperatures of −15.5 ℃ and −20.5 ℃ were selected to realize desublimation conditions, where the dew point is below freezing point. Frost formations on the AgI-patterned and bare resin surfaces were compared. On the AgI dot-patterned surface, frost nucleated selectively at certain AgI dots and grew horizontally, forming isolated columnar and planar crystals. These structures remained spatially separated for over 3 hours. In contrast, the bare surface exhibited typical frost behavior, i.e. dropwise condensation, droplet freezing, ice bridging, and eventually full coverage. Frost growth rate increased at lower surface temperature on both surfaces. On the AgI-patterned surface, the combination of higher ambient temperature and lower surface temperature further promoted nucleation and growth from the AgI dots, enhancing horizontal crystal development. To reconstruct the 3D frost structures, the replica method was applied. The AgI-patterned surface exhibited clear, laterally extended frost morphologies, while the bare PET surface showed random, interconnected frost growth. These results demonstrate that AgI dot patterns can effectively localize nucleation and preserve isolated and directional frost growth, offering a valuable approach for investigating frost growth mechanisms and developing frost controlling strategy.


  • Open Access

    Frost growth on silver iodide (AgI) stripe patterned surface under condensation frosting condition

    by Jinchen Tang, Takao Okabe, Katsuhiko Nishimura, Anna Sciazko, Hang Zhang, Naoki Shikazono


  • Open Access

    Fabrication of Silver Iodide (AgI) Patterns via Photolithography and Its Application to In-Situ Observation of Condensation Frosting

    by Takao Okabe, Jinchen Tang, Katsuhiko Nishimura, Naoki Shikazono

    This study introduces an innovative photolithography-based method for patterning ionic and inorganic particle materials such as silver iodide (AgI). Conventional methods lack precision when patterning powdered materials, which limits their applicability. The proposed method stacks layers of a particle material (AgI) and negative-tone photoresist for simultaneous ultraviolet exposure and development, resulting in well-defined AgI patterns. The sintering process successfully removed binders from the material layer and photoresist, yielding standalone AgI patterns on the Si substrate with good adhesion. The pitch remained consistent with the design values of the photomask when the pattern size was changed. In-situ observation of condensation frosting on the patterns was conducted, which confirmed the practicality of the developed patterning process. This versatile method is applicable to large areas with a high throughput and presents new opportunities for modifying functional surfaces.