Surjava Sanyal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Surjava Sanyal has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Chirag Gupta
Department of Electrical and Computer Engineering, University of Wisconsin-Madison , Madison, Wisconsin 53706
12 shared publications - Shubhra S. Pasayat
Department of Electrical and Computer Engineering, University of Wisconsin-Madison , Madison, Wisconsin 53706
12 shared publications - Swarnav Mukhopadhyay
Department of Electrical and Computer Engineering, University of Wisconsin-Madison , Madison, Wisconsin 53706
11 shared publications - Guangying Wang
Department of Electrical and Computer Engineering, University of Wisconsin-Madison , Madison, Wisconsin 53706
9 shared publications - Ruixin Bai
Department of Electrical and Computer Engineering, University of Wisconsin-Madison, Madison, WI, USA
9 shared publications Chirag Gupta
Department of Electrical and Computer Engineering University of Wisconsin‐Madison Madison Wisconsin USA
5 shared publications
Latest Publications
- 2 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (18)
Normally off behavior of high Al composition AlGaN channel HEMT with p-NiO gate dielectric and barrier recess
High aluminum (Al) composition AlGaN has emerged as a promising material for next generation power semiconductor devices. In this work, we have demonstrated a normally off Al0.84Ga0.16N/Al0.65Ga0.35N high electron mobility transistor (HEMT) with threshold voltage (Vth) ranging from −0.07 to 1.30 V by utilizing radio frequency magnetron sputtered p-type NiO and barrier recess in the gate region. The maximum breakdown voltage of these devices was measured to be 1770 V, corresponding to an average breakdown field of ∼1.26 MV/cm. The device exhibited a maximum drain current of 27.4 mA/mm at a gate-to-source voltage (Vgs) of 2.5 V and a drain-to source voltage (Vds) of 10 V. The sputtering condition of p-NiO with various Ar:O2 ratios was characterized using x-ray photoelectron spectroscopy and the transfer length method. Under Ar:O2 = 3:4, p-NiO showed the lowest Rsheet as well as the highest Ni3+/Ni2+ ratio and was adopted for normally off device fabrication. The contributions of the p-NiO and barrier recess in the positive shift of the threshold voltage (Vth) were decoupled by fabricating HEMTs with different p-NiO and barrier recess combinations. With +0.93 to +1.77 V contributed to p-NiO, and +7.09 to +7.33 V contributed to the barrier recess in the gate region. This result provides a low thermal budget alternative to realize normally off AlGaN channel HEMTs.
- 2 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (18)
Normally off behavior of high Al composition AlGaN channel HEMT with p-NiO gate dielectric and barrier recess
High aluminum (Al) composition AlGaN has emerged as a promising material for next generation power semiconductor devices. In this work, we have demonstrated a normally off Al0.84Ga0.16N/Al0.65Ga0.35N high electron mobility transistor (HEMT) with threshold voltage (Vth) ranging from −0.07 to 1.30 V by utilizing radio frequency magnetron sputtered p-type NiO and barrier recess in the gate region. The maximum breakdown voltage of these devices was measured to be 1770 V, corresponding to an average breakdown field of ∼1.26 MV/cm. The device exhibited a maximum drain current of 27.4 mA/mm at a gate-to-source voltage (Vgs) of 2.5 V and a drain-to source voltage (Vds) of 10 V. The sputtering condition of p-NiO with various Ar:O2 ratios was characterized using x-ray photoelectron spectroscopy and the transfer length method. Under Ar:O2 = 3:4, p-NiO showed the lowest Rsheet as well as the highest Ni3+/Ni2+ ratio and was adopted for normally off device fabrication. The contributions of the p-NiO and barrier recess in the positive shift of the threshold voltage (Vth) were decoupled by fabricating HEMTs with different p-NiO and barrier recess combinations. With +0.93 to +1.77 V contributed to p-NiO, and +7.09 to +7.33 V contributed to the barrier recess in the gate region. This result provides a low thermal budget alternative to realize normally off AlGaN channel HEMTs.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (10) , 1999-2002
High-Voltage (600 V) Dynamic Switching in Al 0.6 Ga 0.4 N-Channel HEMTs With Multiple Field-Plates
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (10) , 1999-2002
High-Voltage (600 V) Dynamic Switching in Al 0.6 Ga 0.4 N-Channel HEMTs With Multiple Field-Plates
- Open Access
- 27 May 2026
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 20 (5)
Kilo‐Volt Class Al 0.65 Ga 0.35 N Channel Metal Insulator Semiconductor HEMTs With >300MW/cm 2 Baliga Figure of Merit on Sapphire Substrate
In this work, we demonstrate an Al‐rich AlGaN channel metal insulator semiconductor HEMT device operating at >2 kV on a sapphire substrate. Devices with 2and 2.6 kV breakdown voltage demonstrated a Baliga figure of merit (BFOM) of 288 and 325 MW/cm 2 with an on‐resistance of 14.15 and 21.02 mΩ.cm 2 , respectively. Reported BFOM of 325 MW/cm 2 value is 1.7 times the state‐of‐the‐art passivated AlGaN channel transistors on sapphire substrate. The obtained results represent the potential of the ultra‐wide bandgap (UWBG) AlGaN channel transistors for advanced power electronics applications.
- 27 May 2026
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 20 (5)
Open AccessKilo‐Volt Class Al 0.65 Ga 0.35 N Channel Metal Insulator Semiconductor HEMTs With >300MW/cm 2 Baliga Figure of Merit on Sapphire Substrate
In this work, we demonstrate an Al‐rich AlGaN channel metal insulator semiconductor HEMT device operating at >2 kV on a sapphire substrate. Devices with 2and 2.6 kV breakdown voltage demonstrated a Baliga figure of merit (BFOM) of 288 and 325 MW/cm 2 with an on‐resistance of 14.15 and 21.02 mΩ.cm 2 , respectively. Reported BFOM of 325 MW/cm 2 value is 1.7 times the state‐of‐the‐art passivated AlGaN channel transistors on sapphire substrate. The obtained results represent the potential of the ultra‐wide bandgap (UWBG) AlGaN channel transistors for advanced power electronics applications.
- Open Access
- 14 April 2026
- Published by Wiley in Advanced Photonics Research
- Vol. 7 (4)
Demonstration of 2.71% External Quantum Efficiency at 630 nm in Singular 2 μm Red InGaN Micro‐LEDs on Porous GaN for AR/VR Applications
Next‐generation augmented/virtual reality (AR/VR) headsets require ultrasmall (2 in an integrating sphere. To the best of our knowledge, this is the highest reported peak EQE for singular (nonarrayed) InGaN micro‐LEDs with a lateral dimension less than 5 μm and a peak wavelength greater than 620 nm. Based on finite‐difference time‐domain simulations, with silicone encapsulation ( n = 1.54), the EQE could potentially increase to 4.4%. The peak EQE occurs at a low current density of 2.5 A/cm 2 and, along with the small device size (2 μm), makes it attractive for AR/VR applications, which require low power consumption and high pixel density.
- 14 April 2026
- Published by Wiley in Advanced Photonics Research
- Vol. 7 (4)
Open AccessDemonstration of 2.71% External Quantum Efficiency at 630 nm in Singular 2 μm Red InGaN Micro‐LEDs on Porous GaN for AR/VR Applications
Next‐generation augmented/virtual reality (AR/VR) headsets require ultrasmall (2 in an integrating sphere. To the best of our knowledge, this is the highest reported peak EQE for singular (nonarrayed) InGaN micro‐LEDs with a lateral dimension less than 5 μm and a peak wavelength greater than 620 nm. Based on finite‐difference time‐domain simulations, with silicone encapsulation ( n = 1.54), the EQE could potentially increase to 4.4%. The peak EQE occurs at a low current density of 2.5 A/cm 2 and, along with the small device size (2 μm), makes it attractive for AR/VR applications, which require low power consumption and high pixel density.
- 25 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (4) , 688-691
K-Band (20 GHz) Large-Signal Performance in Al 0.65 Ga 0.35 N Channel HEMTs With 2.3-W/mm Output Power and 22.8% Associated PAE
In this work, we demonstrate the power performance of high composition Al ${}_{{0}.{65}}$ Ga ${}_{{0}.{35}}$ N channel high-electron-mobility transistors (HEMTs) operating at 20 GHz (with pulsed passive load-pull), achieving a power-added efficiency (PAE) of 22.86% and output power density (P ${}_{\text {OUT}}\text {)}$ of 2.3 W/mm. These results surpass previously reported ultra-wide bandgap (UWBG) transistors at 20 GHz by nearly 10 times in terms of both POUT and PAE and still represent the highest PAE among even lower-frequency (>8 GHz) UWBG devices. The outstanding performance is attributed to an Al ${}_{{0}.{65}}$ Ga ${}_{{0}.{35}}$ N channel that enables a high breakdown field, and effective dispersion control achieved via a conformal TiN Schottky T-gate deposited by atomic layer deposition (ALD). This work sets a new benchmark for UWBG RF transistors and highlights the potential of AlxGa ${}_{{1}-\text {x}}$ N (x>0.6) channel HEMTs for high-power RF amplifiers.
- 25 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (4) , 688-691
K-Band (20 GHz) Large-Signal Performance in Al 0.65 Ga 0.35 N Channel HEMTs With 2.3-W/mm Output Power and 22.8% Associated PAE
In this work, we demonstrate the power performance of high composition Al ${}_{{0}.{65}}$ Ga ${}_{{0}.{35}}$ N channel high-electron-mobility transistors (HEMTs) operating at 20 GHz (with pulsed passive load-pull), achieving a power-added efficiency (PAE) of 22.86% and output power density (P ${}_{\text {OUT}}\text {)}$ of 2.3 W/mm. These results surpass previously reported ultra-wide bandgap (UWBG) transistors at 20 GHz by nearly 10 times in terms of both POUT and PAE and still represent the highest PAE among even lower-frequency (>8 GHz) UWBG devices. The outstanding performance is attributed to an Al ${}_{{0}.{65}}$ Ga ${}_{{0}.{35}}$ N channel that enables a high breakdown field, and effective dispersion control achieved via a conformal TiN Schottky T-gate deposited by atomic layer deposition (ALD). This work sets a new benchmark for UWBG RF transistors and highlights the potential of AlxGa ${}_{{1}-\text {x}}$ N (x>0.6) channel HEMTs for high-power RF amplifiers.
- Open Access
- 1 February 2026
- Published by IOP Publishing in Applied Physics Express
- Vol. 19 (2) , 021001
Achieving low sheet resistance in Si-doped AlN via low-temperature MOCVD
A low-temperature (LT) metal-organic chemical vapor deposition (MOCVD) technique was developed for obtaining conductive Si-doped AlN thin films. An optimization of the deposition parameters, such as V/III ratio and trimethylaluminum flow rate, enabled state-of-the-art sheet resistance ( R SH ) of 0.47 and 0.76 MΩ/□ and contact resistance ( R C ) of 1.2 × 10 −2 and 3 × 10 −2 Ω cm 2 in 1200 nm n-AlN deposited on bulk AlN and AlN on Sapphire substrate, respectively, with surface roughness below 0.3 nm. The reduced sheet resistance of LT-MOCVD n-AlN indicates lower compensation than high-temperature MOCVD films, establishing LT-MOCVD as an effective route for highly conductive n-AlN thin films.
- 1 February 2026
- Published by IOP Publishing in Applied Physics Express
- Vol. 19 (2) , 021001
Open AccessAchieving low sheet resistance in Si-doped AlN via low-temperature MOCVD
A low-temperature (LT) metal-organic chemical vapor deposition (MOCVD) technique was developed for obtaining conductive Si-doped AlN thin films. An optimization of the deposition parameters, such as V/III ratio and trimethylaluminum flow rate, enabled state-of-the-art sheet resistance ( R SH ) of 0.47 and 0.76 MΩ/□ and contact resistance ( R C ) of 1.2 × 10 −2 and 3 × 10 −2 Ω cm 2 in 1200 nm n-AlN deposited on bulk AlN and AlN on Sapphire substrate, respectively, with surface roughness below 0.3 nm. The reduced sheet resistance of LT-MOCVD n-AlN indicates lower compensation than high-temperature MOCVD films, establishing LT-MOCVD as an effective route for highly conductive n-AlN thin films.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Selective area regrowth of silane-doped GaN achieving record carrier density for ultra-low resistive Ohmic contacts for AlGaN/GaN HEMT
Low-temperature (LT) selective area growth (SAG) of degenerately silicon (Si) doped GaN by metal-organic-chemical vapor deposition (MOCVD) technique yielded a record-high charge carrier concentration (ns) of 2–2.2 × 1020 cm−3 with a mobility of 116–119 cm2/V s, utilizing triethylgallium and silane (SiH4) as gallium and Si precursors, respectively, and trimethylindium as a surfactant. While SiH4-doped GaN typically yields lower carrier concentrations (≤1020 cm−3) than disilane (Si2H6), this work demonstrates that defect and dislocation suppression enables degenerately doped GaN with ns exceeding 1020 cm−3 using the widely adopted SiH4 precursor. The use of an indium surfactant enhanced both ns and mobility by suppressing defect formation, enhancing 2D-step flow deposition mode compared to 3D island deposition mode in highly Si-doped GaN, enabling ns exceeding 1020 cm−3. SAG of LT-n++-GaN contact layer using SiH4 dopant in an AlGaN/GaN high-electron mobility transistor (HEMT) yielded an ultra-low sheet resistance (RSh) of 22 Ω/□ and a surface roughness of 0.33 nm, resulting in a record low Ohmic contact resistance of 0.065 Ω mm, along with a metal/n++-GaN contact resistance of 0.023 Ω mm, two-dimensional electron-gas-to-n++-GaN contact resistance of 0.025 Ω mm, and an access resistance (Rn+) of 0.017 Ω mm. A scaled AlGaN/GaN HEMT showed ultra-low on resistance (RON) of 0.36 Ω mm and a superior RF performance with current gain cutoff frequency (fT) and maximum oscillation frequency (fmax) of 160 and 195 GHz, respectively. Advancements in LT selective area MOCVD growth of n++-GaN using SiH4 enable regrown contacts in ultra-scaled AlGaN/GaN HEMTs, supporting commercialization for mm-wave applications.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Selective area regrowth of silane-doped GaN achieving record carrier density for ultra-low resistive Ohmic contacts for AlGaN/GaN HEMT
Low-temperature (LT) selective area growth (SAG) of degenerately silicon (Si) doped GaN by metal-organic-chemical vapor deposition (MOCVD) technique yielded a record-high charge carrier concentration (ns) of 2–2.2 × 1020 cm−3 with a mobility of 116–119 cm2/V s, utilizing triethylgallium and silane (SiH4) as gallium and Si precursors, respectively, and trimethylindium as a surfactant. While SiH4-doped GaN typically yields lower carrier concentrations (≤1020 cm−3) than disilane (Si2H6), this work demonstrates that defect and dislocation suppression enables degenerately doped GaN with ns exceeding 1020 cm−3 using the widely adopted SiH4 precursor. The use of an indium surfactant enhanced both ns and mobility by suppressing defect formation, enhancing 2D-step flow deposition mode compared to 3D island deposition mode in highly Si-doped GaN, enabling ns exceeding 1020 cm−3. SAG of LT-n++-GaN contact layer using SiH4 dopant in an AlGaN/GaN high-electron mobility transistor (HEMT) yielded an ultra-low sheet resistance (RSh) of 22 Ω/□ and a surface roughness of 0.33 nm, resulting in a record low Ohmic contact resistance of 0.065 Ω mm, along with a metal/n++-GaN contact resistance of 0.023 Ω mm, two-dimensional electron-gas-to-n++-GaN contact resistance of 0.025 Ω mm, and an access resistance (Rn+) of 0.017 Ω mm. A scaled AlGaN/GaN HEMT showed ultra-low on resistance (RON) of 0.36 Ω mm and a superior RF performance with current gain cutoff frequency (fT) and maximum oscillation frequency (fmax) of 160 and 195 GHz, respectively. Advancements in LT selective area MOCVD growth of n++-GaN using SiH4 enable regrown contacts in ultra-scaled AlGaN/GaN HEMTs, supporting commercialization for mm-wave applications.
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2102-2105
>2.7 kV Al0.65Ga0.35N Channel HEMT on Bulk AlN Substrate With >400 MW/cm² Baliga Figure of Merit
Al-rich AlGaN has emerged as a promising material for high-voltage power electronics due to its exceptional critical electric field (>10 MV/cm). In this work, we demonstrate passivated and field-plated high voltage Al0.65Ga0.35N channel transistors. For >2.7 kV breakdown voltage, a high Baliga figure of merit (BFOM) of close to 400 MW/cm2 using gate pad connected and source pad connected field plates were obtained for Al0.65Ga0.35N channel HEMTs. Additionally, we also report a non-passivated Al0.65Ga0.35N channel HEMTs with >3 kV breakdown voltage and a high BFOM of 569 MW/cm². Furthermore, a low contact resistance of ~2.6 Ω·mm for >60% AlGaN channel FETs on bulk AlN substrates was also obtained. These results provide advances which will help establish AlGaN channel transistors as a compelling candidate for next-generation high-voltage power electronics.
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2102-2105
>2.7 kV Al0.65Ga0.35N Channel HEMT on Bulk AlN Substrate With >400 MW/cm² Baliga Figure of Merit
Al-rich AlGaN has emerged as a promising material for high-voltage power electronics due to its exceptional critical electric field (>10 MV/cm). In this work, we demonstrate passivated and field-plated high voltage Al0.65Ga0.35N channel transistors. For >2.7 kV breakdown voltage, a high Baliga figure of merit (BFOM) of close to 400 MW/cm2 using gate pad connected and source pad connected field plates were obtained for Al0.65Ga0.35N channel HEMTs. Additionally, we also report a non-passivated Al0.65Ga0.35N channel HEMTs with >3 kV breakdown voltage and a high BFOM of 569 MW/cm². Furthermore, a low contact resistance of ~2.6 Ω·mm for >60% AlGaN channel FETs on bulk AlN substrates was also obtained. These results provide advances which will help establish AlGaN channel transistors as a compelling candidate for next-generation high-voltage power electronics.
- Open Access
- 23 July 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (8)
Demonstration of high Johnson’s figure of merit (ft × VBR > 20 THz·V) and fmax × VBR (> 42 THz·V) for Al0.66Ga0.34N channel MISHEMT on bulk AlN substrates
In this letter, a MOCVD-grown Al0.66Ga0.34N channel Metal-Insulator-Semiconductor-High-Electron-Mobility-Transistor (MISHEMT) with a scaled T-gate structure was fabricated on a single-crystal bulk AlN substrate. A device with 4 μm source-to-drain spacing achieved a record-high Johnson’s figure of merit (JFOM) of 20.92 THz·V, enabled by the high-Al channel, high-quality substrate and gate field-plate. The corresponding cutoff and maximum oscillation frequencies are 22.5 GHz and 46 GHz, respectively, with a breakdown voltage of 930 V. A current collapse of 15% was observed under 30 V drain bias, indicating excellent RF performance and the potential of bulk-AlN-based AlGaN channel HEMTs for advanced RF applications
- 23 July 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (8)
Open AccessDemonstration of high Johnson’s figure of merit (ft × VBR > 20 THz·V) and fmax × VBR (> 42 THz·V) for Al0.66Ga0.34N channel MISHEMT on bulk AlN substrates
In this letter, a MOCVD-grown Al0.66Ga0.34N channel Metal-Insulator-Semiconductor-High-Electron-Mobility-Transistor (MISHEMT) with a scaled T-gate structure was fabricated on a single-crystal bulk AlN substrate. A device with 4 μm source-to-drain spacing achieved a record-high Johnson’s figure of merit (JFOM) of 20.92 THz·V, enabled by the high-Al channel, high-quality substrate and gate field-plate. The corresponding cutoff and maximum oscillation frequencies are 22.5 GHz and 46 GHz, respectively, with a breakdown voltage of 930 V. A current collapse of 15% was observed under 30 V drain bias, indicating excellent RF performance and the potential of bulk-AlN-based AlGaN channel HEMTs for advanced RF applications