BVBadri Vishal

Badri Vishal

*This is an algorithmically generated author record based on publicly available information.

Badri Vishal has a total of 90 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Author Correction: Perovskite lattice compliance enables efficient and stable bifacial perovskite/silicon tandem photovoltaics

    by Fuzong Xu, Jiang Liu, Xuechun Zhang, Vladyslav Hnapovskyi, Ilhan Yavuz, Caner Deger, Wenpei Li, Arsalan Razzaq, Lujia Xu, Badri Vishal, et al.

  • Perovskite lattice compliance enables efficient and stable bifacial perovskite/silicon tandem photovoltaics

    by Fuzong Xu, Jiang Liu, Xuechun Zhang, Vladyslav Hnapovskyi, Ilhan Yavuz, Caner Deger, Wenpei Li, Arsalan Razzaq, Lujia Xu, Badri Vishal, et al.

  • Top Cited Papers

    Multivalent ligands regulate dimensional engineering for inverted perovskite solar modules

    by Xiaoming Chang, Yanping Liu, Yue Ping, Nan Wu, Tinghuan Yang, Chenqing Tian, Zhaoheng Ling, Badri Vishal, Anil Reddy Pininti, Jong Bin Park, et al.

    Multivalent, resonance-stabilized amidinium ligands enable stronger chemical coordination and reduced deprotonation compared with conventional monovalent ammonium ligands in low-dimensional perovskites. Here, we introduce a controllable one- to two-dimensional (1D-to-2D) structural transition strategy by systematically tuning ligand conformation, thereby modulating hydrogen bonding, π–π stacking, and basicity to elucidate the relationship between molecular structure, interfacial interactions, and resulting dimensionality. The 1D-amidinium perovskite structure, with its pronounced geometric anisotropy, impedes uniform surface coverage and defect passivation. In contrast, the 2D-amidinium perovskite forms a continuous, homogeneous interfacial layer, enabling more effective defect passivation and favorable energy-level alignment. With dimensionality control, inverted 3D/2D-amidinium perovskite solar cells deliver 25.4% power conversion efficiency (1.1 square centimeters, steady-state certified) and maintain >95% of their initial efficiency after 1100 hours of continuous 1-sun operation at 85°C.


  • Top Cited Papers

    Electron accumulation across the perovskite layer enhances tandem solar cells with textured silicon

    by Oussama Er-Raji, Christoph Messmer, Rakesh R. Pradhan, Oliver Fischer, Vladyslav Hnapovskyi, Sofiia Kosar, Marco Marengo, Mathias List, Jared Faisst, José P. Jurado, et al.

    Reducing charge carrier transport losses, improving selectivity, and minimizing nonradiative recombination are essential for enhancing the efficiency and stability of perovskite/silicon tandem solar cells. We used a hybrid two-step perovskite deposition method that is compatible with industry-standard textured silicon, incorporating a perovskite surface treatment based on 1,3-diaminopropane dihydroiodide. The interaction of this molecule with the perovskite surface increased the majority charge carrier concentration at the electron-selective contact, which reduced interfacial recombination. Simultaneously, this field-effect passivation increased the electron concentration across the entire intrinsic perovskite absorber, which increased conductivity and reduced transport losses. Combined, this yields high-performance, fully textured perovskite/silicon tandem solar cells, achieving a 1-sun AM1.5G conversion efficiency of 33.1% with an open-circuit voltage of 2.01 volts and an extended outdoor stability in the Red Sea Coast.


  • Open Access

    Cs‐Doped and Cs‐S Co‐Doped CuI p‐Type Transparent Semiconductors with Enhanced Conductivity

    by Adeem S. Mirza, Badri Vishal, Pia Dally, Claudia S. Schnohr, Stefaan De Wolf, Monica Morales‐Masis

    One hindrance in transparent electronics is the lack of high‐performance p‐type transparent conductors (TCs). The state‐of‐the‐art p‐type TC, CuI, has a conductivity two orders of magnitude lower than n‐type TCs like ITO. While doping strategies have shown promise in enhancing the hole carrier density in CuI, they often come at the expense of hole mobility. Therefore, understanding how extrinsic dopants affect the mobility of CuI is critical to further improve the performance of CuI‐based TCs. Here the structural and electronic properties of Cs‐doped CuI are investigated. It is demonstrated that ≈4 at.% Cs doping in CuI increases the carrier density from 2.1 × 1019 to 3.8 × 1020 cm−3 while preserving the film microstructure and local coordination of Cu, as confirmed by HRTEM and XAS analysis. Introducing S as a co‐dopant in Cs:CuI boosts the carrier density to 8.2 × 1020 cm−3, reaching a stable conductivity of ≈450 S cm−1. In all cases, the enhanced carrier density negatively affects the hole mobility with ionized impurity scattering and increased Seebeck hole effective mass as mobility limiting mechanisms. Nonetheless, the new Cs, S co‐doped CuI exhibits high p‐type conductivity, Vis–NIR transparency, and stability, presenting an attractive candidate for future transparent electronic devices.


  • Open Access

    Single-Source Pulsed Laser Deposited Perovskite Solar Cells with >19% Efficiency

    by Tatiana Soto-Montero, Suzana Kralj, Randi Azmi, Manuel A. Reus, Junia S. Solomon, Daniel M. Cunha, Wiria Soltanpoor, Drajad Satrio Utomo, Esma Ugur, Badri Vishal, et al.

    Single-source vapor deposition of metal halide perovskites has, to date, remained challenging due to the dissimilar volatilities of the perovskite precursors, limiting the controlled transfer of multiple elements at once. Here, we demonstrate that pulsed laser deposition (PLD) addresses the rate-control challenges of single-source evaporation, enabling solar cells with power conversion efficiencies above 19%. We combined dry mechanochemical synthesis and PLD to fabricate MA1-xFAxPbI3 and Cl-passivated MA1-xFAxPbI3 films from a single-source target. The films are grown onto hole-selective self-assembled monolayers, where first a thin PbI2-rich layer forms, leading to full perovskite conversion. Onto the perovskite, an oleylammonium iodide (OAmI) post-treatment is then applied to passivate its top surface by forming a 2D perovskite film. When incorporating PbCl2 in the target and OAmI-based 2D passivation, a remarkable 19.7% efficiency for p–i–n perovskite solar cells is achieved with enhanced device stability. This highlights the appeal of PLD to fully unlock the potential of single-source vapor-deposited perovskite towards low-cost and efficient photovoltaics.