Seokkan Ki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Seokkan Ki has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Soosik Bang
Department of Mechanical Engineering, Kyung Hee University, Yongin, 17104, Republic of Korea
2 shared publications - Youngsuk Nam
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, Republic of Korea
2 shared publications Bong Jae Lee
1 shared publication- Changsoon Choi
Department of Electronic Engineering and Biomedical Engineering Hanyang University Seoul 04763 South Korea
1 shared publication Chulmin Ahn
1 shared publicationDongwhi Choi
Department of Mechanical Engineering Kyung Hee University Yongin 17 104 Republic of Korea
1 shared publication
Latest Publications
- Open Access
Shape-Controlled Poly(N-isopropylacrylamide) Actuators Enabled by Tensile-Stress Mismatch for Temperature-Adaptive Textiles
Thermal comfort is a key determinant of human health and requires adaptive responses to dynamic environments. Here, we report a temperature-adaptive textile enabled by a tensile stress mismatch-driven poly(N-isopropylacrylamide) (PNIPAM) actuator operating within a human-friendly temperature range of 18–38 °C. A pre-stretched polyurethane core fiber integrated within a PNIPAM sheath in a noncoaxial configuration induces programmable bending through tensile-stress mismatch between elastic recovery and hydrogel swelling. Unlike conventional bilayer hydrogel actuators based on differential swelling between laminated layers, this pre-stretching strategy amplifies structural deformation through elastic restoring stress. When extended to a two-dimensional textile architecture, this strategy enables reversible, dynamic pore modulation with an approximately 400% increase in pore area. This study provides a promising platform for smart adaptive textiles, wearable healthcare, and soft robotics.
Open AccessShape-Controlled Poly(N-isopropylacrylamide) Actuators Enabled by Tensile-Stress Mismatch for Temperature-Adaptive Textiles
Thermal comfort is a key determinant of human health and requires adaptive responses to dynamic environments. Here, we report a temperature-adaptive textile enabled by a tensile stress mismatch-driven poly(N-isopropylacrylamide) (PNIPAM) actuator operating within a human-friendly temperature range of 18–38 °C. A pre-stretched polyurethane core fiber integrated within a PNIPAM sheath in a noncoaxial configuration induces programmable bending through tensile-stress mismatch between elastic recovery and hydrogel swelling. Unlike conventional bilayer hydrogel actuators based on differential swelling between laminated layers, this pre-stretching strategy amplifies structural deformation through elastic restoring stress. When extended to a two-dimensional textile architecture, this strategy enables reversible, dynamic pore modulation with an approximately 400% increase in pore area. This study provides a promising platform for smart adaptive textiles, wearable healthcare, and soft robotics.
- Open Access
- 18 April 2024
- Published by Wiley in Advanced Science
- Vol. 11 (23) , e2310185
Sustainable Thermal Regulation of Electronics via Mitigated Supercooling of Porous Gallium‐Based Phase Change Materials
Gallium liquid metal is one of the promising phase change materials for passive thermal management of electronics due to their high thermal conductivity and latent heat per volume. However, it suffers from severe supercooling, in which molten gallium does not return to solid due to the lack of nucleation. It may require 28.2 °C lower temperature than the original freezing point to address supercooling, leading to unstable thermal regulation performance along fluctuations of cooling condition. Here, gallium is infused into porous copper in an oxide‐free environment, forming intermetallic compound impurities at the interfaces to reduce the activation energy for heterogeneous nucleation. The porous‐shaped gallium provides ≈63% smaller supercooling than that of the bulk type due to large specific surface area (≈9,070 cm 2 per cm 3 ) and high wetting characteristics (≈16° of contact angle) on CuGa 2 intermetallic layer. During repetitive heating‐cooling cycles, porous‐shaped gallium consistently shows propagation of crystallization at even near room temperature (≈25 °C) while maintaining stable performance as thermal buffer, whereas droplet‐shaped gallium is gradually degraded due to partial‐supercooled state. The findings will improve the responsive thermal regulation performance to relieve a rapid increase in temperature of semiconductors/batteries, and also have a potential for energy storage applications.
- 18 April 2024
- Published by Wiley in Advanced Science
- Vol. 11 (23) , e2310185
Open AccessSustainable Thermal Regulation of Electronics via Mitigated Supercooling of Porous Gallium‐Based Phase Change Materials
Gallium liquid metal is one of the promising phase change materials for passive thermal management of electronics due to their high thermal conductivity and latent heat per volume. However, it suffers from severe supercooling, in which molten gallium does not return to solid due to the lack of nucleation. It may require 28.2 °C lower temperature than the original freezing point to address supercooling, leading to unstable thermal regulation performance along fluctuations of cooling condition. Here, gallium is infused into porous copper in an oxide‐free environment, forming intermetallic compound impurities at the interfaces to reduce the activation energy for heterogeneous nucleation. The porous‐shaped gallium provides ≈63% smaller supercooling than that of the bulk type due to large specific surface area (≈9,070 cm 2 per cm 3 ) and high wetting characteristics (≈16° of contact angle) on CuGa 2 intermetallic layer. During repetitive heating‐cooling cycles, porous‐shaped gallium consistently shows propagation of crystallization at even near room temperature (≈25 °C) while maintaining stable performance as thermal buffer, whereas droplet‐shaped gallium is gradually degraded due to partial‐supercooled state. The findings will improve the responsive thermal regulation performance to relieve a rapid increase in temperature of semiconductors/batteries, and also have a potential for energy storage applications.
- 1 March 2021
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 161, 106708
A bio-inspired, low pressure drop liquid cooling system for high-power IGBT modules for EV/HEV applications
- 1 March 2021
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 161, 106708
A bio-inspired, low pressure drop liquid cooling system for high-power IGBT modules for EV/HEV applications