HAHind Hadi Abdulridha

Hind Hadi Abdulridha

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hind Hadi Abdulridha has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of Severe Plastic Deformation on Mechanical Properties for A6061 Aluminum Alloy Fabricated by Multitypes of Bending Forming

    by Raed R. Shwaish, Mazin Al-Wswasi, Hind H. Abdulridha, Aseel Hamad Abed, Waleed Ahmed

    Severe plastic deformation (SPD) is a well‐known processing technique used to impose large plastic strains and modify the mechanical properties of metal‐based materials. In this work, SPD was introduced into A6061 aluminum alloy sheets via two forming processes: differential diameter rolling (DDR) and V‐bending. This hybrid DDR V‐bending approach addresses the limited understanding of how shear‐dominated prestraining produced by asymmetric rolling affects the subsequent bending response, spring‐back behavior, and energy absorption of A6061 aluminum alloy sheets, which are not fully captured by conventional symmetric rolling. The DDR process was performed at a rolling speed ratio of 1.15 using four sample reorientation conditions between successive passes, denoted as ND‐, RD‐, TD‐, and UD‐based routes. The thickness reduction ratios were 20%, 30%, and 40%, performed through three passes of the DDR process. Following the DDR process, the sheets were bent via a 90° V‐die to assess the following mechanical properties: hardness, maximum bending load, bending deflection, bending energy absorption, and spring‐back. Results of the experiments indicated that the thickness reduction ratio had a positive influence on strain hardening, leading to an increase in both hardness and spring‐back. However, the maximum bending load decreased with an increase in thickness reduction ratio, which occurs due to the reduction in the sheet thickness following the DDR process. Furthermore, the spring‐back angle and spring‐back factors were found to be higher for samples processed via the ND and RD rolling routes. The sheets rolled along the ND route produced the highest improvement in mechanical properties. Bending energy absorption increased with an increase in the thickness reduction ratio. The results of this study demonstrate that the DDR‐V‐bending process is effective in the modification of mechanical properties of A6061 aluminum alloy sheets. However, the reduction in bending load indicates a potential negative impact of the DDR process on the formability of the sheets.

  • Multi-objective optimization and prediction of milling parameters for Al 6061 alloy using desirability analysis and artificial neural networks

    by Alaa H Shabeeb, Hind H Abdulridha, Nareen Hafidh Obaeed, Momena M Mohammed

    This study focuses on developing a predictive model for surface roughness and material removal rate (MRR) in the machining of Al 6061 using a three-axis CNC vertical milling machine under dry-cutting conditions. The Taguchi design of experiments (L9 orthogonal array) and Artificial Neural Networks (ANNs) were employed to optimize and predict machining performance. The effects of milling parameters, including spindle speed, feed rate, and depth of cut, were assessed using Analysis of Variance (ANOVA), and a neural network model of two layers and fifteen neurons was constructed. ANOVA results identified spindle speed as the most influential parameter, contributing 88.76% to average surface roughness (Ra) and 65.16% to material removal rate. The experimental results indicated that best machining parameters delivered both a 1.52 μm Ra finishing and 179.857 mm3 min−1 MRR maximum. The prediction accuracy of Ra and MRR through the feed-forward ANN illustrated mean squared errors of 0.003 and 1.1584 respectively. As a consequence, Taguchi’s method and ANN modeling have been combined to develop a comprehensive system for milling parameter optimization using a smaller number of experiments while at the same time delivering superior prediction precision. The study offers critical insights about improving Al 6061 milling quality and productivity that extends to precision manufacturing applications.


  • Open Access

    Optimization of fused deposition modeling parameters for polyethylene terephthalate glycol flexural strength and dimensional accuracy

    by Hind Hadi Abdulridha, Nareen Hafidh Obaeed, Adil Shbeeb Jaber

    Fused Deposition Modeling (FDM) is a type of additive manufacturing (AM) that has received significant interest from researchers and industries due to its flexibility in design, efficient use of materials, and affordable costs. In this paper, the main objective is to investigate the influences of...


  • Open Access

    Investigating the Impact of EDM Parameters on Surface Roughness and Electrode Wear Rate in 7024 Aluminum Alloy

    by Safaa Kadhim Ghazi, Mostafa Adel Abdullah, Hind Hadi Abdulridha

    Electrical Discharge Machining (EDM) is a significant process in the industry for machining hard metals. It is a time-consuming and costly method that requires a high level of expertise to operate effectively. EDM is considered one of the unconventional operating processes due to its unique characteristics and the challenges associated with its implementation. One of the challenges facing researchers is determining the optimal parameters for achieving high surface quality while minimizing equipment consumption and associated costs. In addition to being classified as one of the operating processes, EDM processes are also classified as electro-thermal processes that affect surface quality. In this study, the influence of EDM parameters on surface roughness and electrode wear rate when machining aluminum alloy type 7024 was investigated. A total of 27 experiments were conducted to evaluate the impact of three parameters at three levels. The parameters under investigation include current, pulse on time, and pulse off time. Subsequent analysis of the results by variance analysis revealed that the most influential parameter for both surface roughness and electrode wear rate is electric current, with a rate of influence of 74%. The results were then subjected to further analysis using variable effect graphs to identify the optimal variables for achieving the best results. Finally, neural networks were employed to predict the results, with an accuracy of up to 99%.


  • Open Access

    Predicting Mechanical Strength and Optimized Parameters in FDM-Printed Polylactic Acid Parts Via Artificial Neural Networks and Desirability Analysis

    by Hind H. Abdulridha, Tahseen F. Abbas, Aqeel S. Bedan

    Fused deposition modeling (FDM) is a commonly used additive manufacturing (AM) technique in both domestic and industrial end-product fabrications. It produces prototypes and parts with complex geometric designs, which has the major benefits of eliminating the need for expensive tooling and flexibility. However, the produced parts often face poor part strength due to anisotropic fabrication strategies. The printing procedure, the kind of material utilized, and the printing parameters all have a significant impact on the mechanical characteristics of the printed item. In order to predict the mechanical properties related to printed components made with the use of FDM and Polylactic Acid (PLA) material, this study concentrates on developing a prediction model utilizing Artificial Neural Networks (ANNs). This study used the Taguchi design of experiments technique, utilizing (L25) orthogonal array as well as a Neural Network (NN) method with two layers and 15 neurons. The effect of FDM parameters (layer thickness (mm), percentage of infill density, number of top/bottom layers, shell thickness (mm), and infill overlap percentage) on ultimate tensile and compressive strength (UTS and UCS) was examined through analysis of variance (ANOVA). With an ANOVA result of 67.183% and 40.198%, respectively, infill density percentage was found to be the most significant factor influencing UCS and UTS dependent on other parameters. The predicted results demonstrated valuable agreement with experimental values, with mean squared errors of (0.098) and (0.326) for UTS and UCS, respectively. The predictive model produces flexibility in selecting the optimal setting based on applications.


  • Open Access

    Investigate the Effect of Chemical Post Processing on the Surface Roughness of Fused Deposition Modeling Printed Parts

    by Hind Hadi Abdulridha, Tahseen Fadhil Abbas, Aqeel Sabree Bedan

    Fused deposition modeling (FDM) technology is one of the rapidly growing techniques used for producing various complicated configurations without the need for any tools or continuous human intervention. However, a low quality of surfaces results for the layered production used in FDM. It is...


  • Optimizing the MRR in WEDM process by using Taguchi analysis and GA technique

    by Marwa Qasim Ibraheem, Nareen Hafidh Obaeed, Hind Hadi Abdulridha

    One of the most commonly utilized machines is the Wire Electric Discharge Machine (WEDM) for cutting conductive metals of any hardness that are challenging or i One of the most commonly utilized machines is the Wire Electric Discharge Machine (WEDM) for cutting conductive metals of any hardness that are challenging or i


  • Open Access

    Analyzing the Impact of FDM Parameters on Compression Strength and Dimensional Accuracy in 3D printed PLA Parts

    by Hind H. Abdulridha, Tahseen F. Abbas

    Fused deposition modeling (FDM) is an additive manufacturing (AM) technique frequently used to create prototypes and parts with intricate geometrical designs. It is gaining popularity since it enhances products by removing the need for expensive equipment. The materials used, the printing process, and the parameters influence the mechanical properties of printed objects. The quality and functionality of the parts are impacted by FDM process parameters. This study focused on the impact of six parameters on the mechanical and physical properties of samples printed using the FDM machine (Creality Ender-5 Pro). The infill density percentage, infill pattern, layer thickness, shell thickness, number of top/bottom layers, and the percentage of infill overlap have been taken as the process parameters. The compressive strength has been calculated using the ASTM D695 compression test. The results illustrated how printing parameters affected samples' mechanical and physical properties, which were proven by the ultimate compression stress UCS and the percentage of compression average deviation. The analysis of variance shows the significance of infill density (100%) for UCS, while layer thickness (0.15 mm) is significant for compression average percentage deviation. For instance, the increase in the infill density from 20% to 100% shows that the strength climbed from 4 MPa to 56.5 MPa. Similarly, reducing layer thickness from 0.3 mm to 0.15 mm results in a diminished dimensional accuracy deviation from 1.65% to 0.446%, approximately three times less than that of the specimen with a 0.3 mm layer thickness.


  • Open Access

    Analysis and Investigation the Effect of the Printing Parameters on the Mechanical and Physical Properties of PLA Parts Fabricated via FDM Printing

    by Hind Hadi Abdulridha, Tahseen Fadhil Abbas

    Fused deposition modeling (FDM) is a commonly used additive manufacturing (AM) technique that creates prototypes and parts with intricate geometrical designs. It is gaining popularity since it enhances products by removing the need for expensive equipment. The printed item's mechanical properties...