Shahab Mahmoudi Sadaghiani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shahab Mahmoudi Sadaghiani has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Sharmistha Bhadra
Department of Electrical and Computer Engineering, McGill University, Montreal, QC, Canada
2 shared publications - Amir Ardakani
Department of Electrical and Computer Engineering, McGill University, Montreal, Canada
1 shared publication - Hossein Anabestani
Department of Electrical Engineering, McGill University, 845 Sherbrooke St W, Montreal, QC H3A 0G4, Canada
1 shared publication
Latest Publications
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 12680-12695
Low-Power Wearable for PPG Sensing in No-LED and Low-Intensity LED Modes
In this research, we introduce an innovative wearable device capable of capturing photoplethysmography (PPG) signals under two conditions: No-LED and low-intensity LED. Incorporation of both modes substantially reduces power consumption by recording the PPG signal without active light emission when there is sufficient ambient light, thereby enhancing the device’s overall energy efficiency and extending its battery life. The wearable device consists of two main parts: the ring (sensor) and the bracelet (read-out unit) which are connected by a flexible connector. The design of the ring and the placement of the LEDs and photodiodes in the ring have been optimized to ensure consistent PPG signal acquisition across diverse user profiles. An accelerometer is integrated in the ring to mitigate motion artifacts from PPG signal. The bracelet part receives PPG and accelerometer data from the ring and transmits them wirelessly to a remote device for further processing and display. Our experimental results indicate that the proposed system achieves a maximum measurement error of 3 bpm for heart rate and 2.9% for oxygen saturation compared to the reference measurements, demonstrating the wearable’s capability to capture PPG signals in both modes. The readout of our wearable device consumes 262.5 μW continuously in no LED mode and 652.5μW in low-intensity LED mode, indicating the No-LED mode can significantly extend the battery life. The proposed wearable engineered to acquire two different wavelengths PPG signals in low-intensity LED and No-LED modes has potential for accurate monitoring of vital physiological parameters while reducing power consumption.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 12680-12695
Low-Power Wearable for PPG Sensing in No-LED and Low-Intensity LED Modes
In this research, we introduce an innovative wearable device capable of capturing photoplethysmography (PPG) signals under two conditions: No-LED and low-intensity LED. Incorporation of both modes substantially reduces power consumption by recording the PPG signal without active light emission when there is sufficient ambient light, thereby enhancing the device’s overall energy efficiency and extending its battery life. The wearable device consists of two main parts: the ring (sensor) and the bracelet (read-out unit) which are connected by a flexible connector. The design of the ring and the placement of the LEDs and photodiodes in the ring have been optimized to ensure consistent PPG signal acquisition across diverse user profiles. An accelerometer is integrated in the ring to mitigate motion artifacts from PPG signal. The bracelet part receives PPG and accelerometer data from the ring and transmits them wirelessly to a remote device for further processing and display. Our experimental results indicate that the proposed system achieves a maximum measurement error of 3 bpm for heart rate and 2.9% for oxygen saturation compared to the reference measurements, demonstrating the wearable’s capability to capture PPG signals in both modes. The readout of our wearable device consumes 262.5 μW continuously in no LED mode and 652.5μW in low-intensity LED mode, indicating the No-LED mode can significantly extend the battery life. The proposed wearable engineered to acquire two different wavelengths PPG signals in low-intensity LED and No-LED modes has potential for accurate monitoring of vital physiological parameters while reducing power consumption.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (1) , 931-942
Ambient Light-Driven Wireless Wearable Finger Patch for Monitoring Vital Signs From PPG Signal
In recent years, wearable health monitoring using photoplethysmography (PPG) has become a popular trend. However, one of the main challenges of PPG sensing is the power usage of the LED in the technique. In this work, we designed a wireless wearable finger patch that can record PPG signals solely using ambient light, entirely eliminating the requirement for LED power consumption. The finger patch is implemented on a two-layer flexible polyimide substrate and is based on a high sensitivity silicon photodiode and a high dynamic range analog front end. The entire circuit is powered by a rechargeable Li-ion coin battery. It also uses a Bluetooth module to send the PPG data wirelessly. The system is validated with 12 healthy subjects for the collection of PPG signals under three ambient light conditions. Assessment of the PPG signals quality demonstrates that the PPG signals acquired under the ambient light conditions can be placed in the reliable or acceptable category. Finally, two vital signs: heart rate (HR) and blood pressure (BP) are extracted from the No-LED mode PPG signals obtained from 12 subjects using the finger patch. The calculated maximum mean absolute error (MAE) for HR in comparison to the reference measurement is small (3.4 BPM). For BP prediction AlexNet network with training of all layers with finger patch PPG data shows better performance and produces BP with an average MAE of 8.1 mmHg and 6.05 mmHg for systolic and diastolic BP, respectively. Without any need to turn on any LED, the finger patch can save power and will have the potential for long term health monitoring without frequently charging batteries.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (1) , 931-942
Ambient Light-Driven Wireless Wearable Finger Patch for Monitoring Vital Signs From PPG Signal
In recent years, wearable health monitoring using photoplethysmography (PPG) has become a popular trend. However, one of the main challenges of PPG sensing is the power usage of the LED in the technique. In this work, we designed a wireless wearable finger patch that can record PPG signals solely using ambient light, entirely eliminating the requirement for LED power consumption. The finger patch is implemented on a two-layer flexible polyimide substrate and is based on a high sensitivity silicon photodiode and a high dynamic range analog front end. The entire circuit is powered by a rechargeable Li-ion coin battery. It also uses a Bluetooth module to send the PPG data wirelessly. The system is validated with 12 healthy subjects for the collection of PPG signals under three ambient light conditions. Assessment of the PPG signals quality demonstrates that the PPG signals acquired under the ambient light conditions can be placed in the reliable or acceptable category. Finally, two vital signs: heart rate (HR) and blood pressure (BP) are extracted from the No-LED mode PPG signals obtained from 12 subjects using the finger patch. The calculated maximum mean absolute error (MAE) for HR in comparison to the reference measurement is small (3.4 BPM). For BP prediction AlexNet network with training of all layers with finger patch PPG data shows better performance and produces BP with an average MAE of 8.1 mmHg and 6.05 mmHg for systolic and diastolic BP, respectively. Without any need to turn on any LED, the finger patch can save power and will have the potential for long term health monitoring without frequently charging batteries.