Mervat Youssef
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mervat Youssef has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Adel Nofal
Metal Casting Department, Manufacturing Technology Institute, Central Metallurgical Research and Development Institute (CMRDI), Cairo 11912, Egypt
2 shared publications - Eman H. El-Shenawy
Plastic Deformation Department, Metal Technology Institute, Central Metallurgical Research and Development Institute (CMRDI), Cairo 11912, Egypt
2 shared publications - Mohsen Abdelnaeim Hassan
School of Innovative Design Engineering (IDE), Egypt-Japan University of Science and Technology (E-JUST), Alexandria 21934, Egypt
2 shared publications - Tadaharu Adachi
Department of Mechanical Engineering, Toyohashi University of Technology (TUT), Aichi 441-8122, Japan
2 shared publications - Wael Khair-Eldeen
School of Innovative Design Engineering (IDE), Egypt-Japan University of Science and Technology (E-JUST), Alexandria 21934, Egypt
2 shared publications Adel Nofal
Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt
1 shared publication
Latest Publications
- Open Access
The Influences of Nb Microalloying and Grain Refinement Thermal Cycling on Microstructure and Tribological Properties of Armor Steel
This study aims to investigate the combined effect of niobium (Nb) microalloying and austenite grain refinement, using a specific heat treatment cycle, on the microstructure and tribological properties of Armox 500T steel. In this work, Nb addition and thermal cycling were utilized for grain refinement and enhancement of the mechanical properties of Armox 500T alloy, to provide improved protection via lightweight armor steel components with a high strength-to-weight ratio. The kinetics of transformation of the developed Armox alloys were studied using JMATPro version 13.2. The samples were subjected to two austenitizing temperatures, 1000 °C and 1100 °C, followed by 4 min of holding time and three consecutive thermal and rapid-quenching processes from 900 °C to room temperature. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) was employed to analyze the microstructure, which primarily consists of four types of martensite: short and long lath martensite, blocky martensite, and equiaxed martensite. Additionally, a small percentage (not exceeding 3%) of carbide precipitates was observed. The wear characteristics of the investigated alloys were evaluated using a pin-on-disc tribometer. The results demonstrate that alloying with Nb and grain refinement using a thermal cycle significantly reduce the wear rate.
Open AccessThe Influences of Nb Microalloying and Grain Refinement Thermal Cycling on Microstructure and Tribological Properties of Armor Steel
This study aims to investigate the combined effect of niobium (Nb) microalloying and austenite grain refinement, using a specific heat treatment cycle, on the microstructure and tribological properties of Armox 500T steel. In this work, Nb addition and thermal cycling were utilized for grain refinement and enhancement of the mechanical properties of Armox 500T alloy, to provide improved protection via lightweight armor steel components with a high strength-to-weight ratio. The kinetics of transformation of the developed Armox alloys were studied using JMATPro version 13.2. The samples were subjected to two austenitizing temperatures, 1000 °C and 1100 °C, followed by 4 min of holding time and three consecutive thermal and rapid-quenching processes from 900 °C to room temperature. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) was employed to analyze the microstructure, which primarily consists of four types of martensite: short and long lath martensite, blocky martensite, and equiaxed martensite. Additionally, a small percentage (not exceeding 3%) of carbide precipitates was observed. The wear characteristics of the investigated alloys were evaluated using a pin-on-disc tribometer. The results demonstrate that alloying with Nb and grain refinement using a thermal cycle significantly reduce the wear rate.
- 3 October 2023
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 57 (5) , 433–440
MICROSTRUCTURE EVOLUTION AND PHASE TRANSFORMATIONS IN MICROALLOYED ARMOX 500T STEEL DURING A DILATATION PROCESS
With this work we successfully developed two modified Armox 500T alloys using microalloying with different amounts of niobium (Nb) and boron (B) to obtain a finer grain size, which in return enhances the remnant properties. Furthermore, different heat-treatment cycles were designed and performed using a quenching dilatometer to study the combined effect of thermal cycling and microalloying with Nb and B on the microstructure and transformation temperatures including the start and finish temperature of the austenite transformation (Ac1, Ac3) and the martensite start and finish temperature (Ms, Mf) of the investigated alloys. Dilatometry results show that increasing the content of Nb from 0.07 w/% to 0.13 w/% and B from 0.0035 to 0.0046 w/% increases the temperature range between Ac1 and Ac3 by 55 °C, indicating a broader range for changing heat-treatment temperatures. In addition, the Ms temperature is reduced by 13 °C due to austenite refinement caused by the microalloying of Nb and B. The effect of the annealing temperature at a constant heating rate showed a significant impact on the austenite grain size and hardness. Furthermore, the kinetics of phase transformations were theoretically studied using Thermo-Calc, and the numerical predictions were confirmed experimentally with dilatometry results. Metallography investigations using a scanning electron microscope (SEM) and an optical microscope (OM) were conducted to evaluate the microstructure evolution of the developed alloys. Hardness tests were performed to evaluate the effect of the grain refinement of martensite lathes caused by microalloying with Nb, B, and heat-treatment thermal cycling. It is found that the hardness of the modified Armox alloys in this research was improved by 14 % in comparison with the conventional Armox 500T.
- 3 October 2023
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 57 (5) , 433–440
MICROSTRUCTURE EVOLUTION AND PHASE TRANSFORMATIONS IN MICROALLOYED ARMOX 500T STEEL DURING A DILATATION PROCESS
With this work we successfully developed two modified Armox 500T alloys using microalloying with different amounts of niobium (Nb) and boron (B) to obtain a finer grain size, which in return enhances the remnant properties. Furthermore, different heat-treatment cycles were designed and performed using a quenching dilatometer to study the combined effect of thermal cycling and microalloying with Nb and B on the microstructure and transformation temperatures including the start and finish temperature of the austenite transformation (Ac1, Ac3) and the martensite start and finish temperature (Ms, Mf) of the investigated alloys. Dilatometry results show that increasing the content of Nb from 0.07 w/% to 0.13 w/% and B from 0.0035 to 0.0046 w/% increases the temperature range between Ac1 and Ac3 by 55 °C, indicating a broader range for changing heat-treatment temperatures. In addition, the Ms temperature is reduced by 13 °C due to austenite refinement caused by the microalloying of Nb and B. The effect of the annealing temperature at a constant heating rate showed a significant impact on the austenite grain size and hardness. Furthermore, the kinetics of phase transformations were theoretically studied using Thermo-Calc, and the numerical predictions were confirmed experimentally with dilatometry results. Metallography investigations using a scanning electron microscope (SEM) and an optical microscope (OM) were conducted to evaluate the microstructure evolution of the developed alloys. Hardness tests were performed to evaluate the effect of the grain refinement of martensite lathes caused by microalloying with Nb, B, and heat-treatment thermal cycling. It is found that the hardness of the modified Armox alloys in this research was improved by 14 % in comparison with the conventional Armox 500T.