Qianyu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qianyu Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ajay Achath Mohanan
Monash University Malaysia
3 shared publications - Howgen Pratama Kesuma
Monash University Malaysia
2 shared publications - Ahmad Shuhaimi
University of Malaya
1 shared publication - Narayanan Ramakrishnan
Monash University Malaysia
1 shared publication - Rizuan Norhaniza
Institute of Graduate Studies, University of Malaya, 50603 Kuala Lumpur, Malaysia
1 shared publication - Yikai Zhao
Universiti Malaya
1 shared publication
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (18) , 27163-27177
Effect of Groove Gratings on the Sensitivity of One-Port SAW Resonators Composed of Polymer Sensing Film-Coated Reflectors
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (18) , 27163-27177
Effect of Groove Gratings on the Sensitivity of One-Port SAW Resonators Composed of Polymer Sensing Film-Coated Reflectors
- Open Access
- 13 August 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 716
Investigation into mass-sensitivity enhancement of acoustically thick polymer sensing film-coated one-port SAW resonators
- 13 August 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 716
Open AccessInvestigation into mass-sensitivity enhancement of acoustically thick polymer sensing film-coated one-port SAW resonators
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Mass Loading Characteristics of One-Port SAW Resonator With Sensing Film Attached Reflector Electrodes
We investigated the mass loading effect caused by a thin polymer film attached only on the reflector electrodes of a one-port surface acoustic wave (SAW) resonator and explored the possibility of devising low-loss SAW sensors. One-port SAW resonators have a miniaturized device footprint and are well known for their high unloaded quality factor (Q). However, despite these advantages, they are less popular for sensing applications than other types of SAW devices due to insufficient space on the device surface for coating a sensing medium without affecting the stability of the resultant sensor response. Accordingly, we fabricated typical one-port SAW resonators operating at the resonant frequency of ∼130 MHz and patterned positive photoresist (considered as typical sensing film) only onto the reflector electrodes. It was observed that mass loading of the film on the device reflectors shifted the resonant frequency ( f 0 ) of the main cavity resonance towards the resonant frequency of the interdigital transducer ( f IDT ) to allow more acoustic wave energy from the IDT to contribute towards exciting the main cavity resonance. The relatively lower mismatch between f 0 and f IDT of the resonator composed of polymer thin film-coated reflectors overcame the viscous damping of SAW contributed by the intrinsic loss in the polymer to increase the Q of the film-coated resonator. The resultant humidity sensor demonstrated a sensitivity of 155.6 Hz/% RH with good repeatability.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Mass Loading Characteristics of One-Port SAW Resonator With Sensing Film Attached Reflector Electrodes
We investigated the mass loading effect caused by a thin polymer film attached only on the reflector electrodes of a one-port surface acoustic wave (SAW) resonator and explored the possibility of devising low-loss SAW sensors. One-port SAW resonators have a miniaturized device footprint and are well known for their high unloaded quality factor (Q). However, despite these advantages, they are less popular for sensing applications than other types of SAW devices due to insufficient space on the device surface for coating a sensing medium without affecting the stability of the resultant sensor response. Accordingly, we fabricated typical one-port SAW resonators operating at the resonant frequency of ∼130 MHz and patterned positive photoresist (considered as typical sensing film) only onto the reflector electrodes. It was observed that mass loading of the film on the device reflectors shifted the resonant frequency ( f 0 ) of the main cavity resonance towards the resonant frequency of the interdigital transducer ( f IDT ) to allow more acoustic wave energy from the IDT to contribute towards exciting the main cavity resonance. The relatively lower mismatch between f 0 and f IDT of the resonator composed of polymer thin film-coated reflectors overcame the viscous damping of SAW contributed by the intrinsic loss in the polymer to increase the Q of the film-coated resonator. The resultant humidity sensor demonstrated a sensitivity of 155.6 Hz/% RH with good repeatability.