Daria Roda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daria Roda has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
A. P. Nowak
Advanced Materials Center, Gdańsk University of Technology, Gdańsk, Poland
2 shared publications- Andrzej Paweł Nowak
Faculty of Chemistry, Department of Chemistry and Technology of Functional Materials, Gdansk University of Technology, Gdansk, Poland
2 shared publications - Anna Ilnicka
Faculty of Chemistry, Nicolaus Copernicus University in Toruń, Toruń, Poland
2 shared publications K. Trzciński
Faculty of Chemistry, Department of Chemistry and Technology of Functional Materials, Gdansk University of Technology, Gdansk, Poland
2 shared publicationsM. Sawczak
Centre for Plasma and Laser Engineering, The Szewalski Institute of Fluid Flow Machinery, Gdańsk, Poland
2 shared publicationsM. Szkoda
Faculty of Chemistry, Department of Chemistry and Technology of Functional Materials, Gdansk University of Technology, Gdansk, Poland
2 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Springer Nature in Scientific Reports
Effects of deposition parameters and cobalt hexacyanocobaltate surface modification on magnetron-sputtered ZnIn₂S₄ thin film photoanodes
For the first time, ZnIn₂S₄ (ZIS) thin films were successfully prepared by magnetron sputtering and systematically investigated as photoanodes for photoelectrochemical (PEC) water splitting. The PEC performance of the layers strongly depended on the deposition parameters. The highest photocurrent density of 2.77 mA cm⁻² at 1.62 V vs. RHE was achieved for films deposited at 200 °C for 90 min, whereas films deposited at 300 °C for 90 min exhibited improved stability. The optimized ZIS photoanode was subsequently modified with a cobalt hexacyanocobaltate (Cohcc) surface layer formed via electrooxidation of a Co layer in an electrolyte containing Co(CN)₆³⁻. This surface modification improved photoanode performance, particularly in terms of stability, likely due to enhanced oxygen evolution reaction (OER) kinetics at the electrode surface. Cohcc-modified photoanode generated almost 3 times higher photocurrent density after 100 s operation compared to unmodified photoanode. Electrochemical measurements performed under dark conditions further confirmed the role of Cohcc as cocatalyst toward OER. Overall, the results demonstrate that magnetron sputtering enables effective control over the properties of ZIS photoanodes through optimization of deposition parameters, while surface modification with cobalt hexacyanocobaltate represents a viable strategy for tuning interfacial kinetics and improving the functional performance of ZIS-based photoanodes.
- 1 October 2026
- Published by Springer Nature in Scientific Reports
Open AccessEffects of deposition parameters and cobalt hexacyanocobaltate surface modification on magnetron-sputtered ZnIn₂S₄ thin film photoanodes
For the first time, ZnIn₂S₄ (ZIS) thin films were successfully prepared by magnetron sputtering and systematically investigated as photoanodes for photoelectrochemical (PEC) water splitting. The PEC performance of the layers strongly depended on the deposition parameters. The highest photocurrent density of 2.77 mA cm⁻² at 1.62 V vs. RHE was achieved for films deposited at 200 °C for 90 min, whereas films deposited at 300 °C for 90 min exhibited improved stability. The optimized ZIS photoanode was subsequently modified with a cobalt hexacyanocobaltate (Cohcc) surface layer formed via electrooxidation of a Co layer in an electrolyte containing Co(CN)₆³⁻. This surface modification improved photoanode performance, particularly in terms of stability, likely due to enhanced oxygen evolution reaction (OER) kinetics at the electrode surface. Cohcc-modified photoanode generated almost 3 times higher photocurrent density after 100 s operation compared to unmodified photoanode. Electrochemical measurements performed under dark conditions further confirmed the role of Cohcc as cocatalyst toward OER. Overall, the results demonstrate that magnetron sputtering enables effective control over the properties of ZIS photoanodes through optimization of deposition parameters, while surface modification with cobalt hexacyanocobaltate represents a viable strategy for tuning interfacial kinetics and improving the functional performance of ZIS-based photoanodes.
- Open Access
- 31 May 2025
- Published by Elsevier in Applied Surface Science
- Vol. 708
ZnIn2S4 thin films grown by pulsed laser deposition: Effect of electrolyte and illumination conditions on photoanode performance
- 31 May 2025
- Published by Elsevier in Applied Surface Science
- Vol. 708
Open AccessZnIn2S4 thin films grown by pulsed laser deposition: Effect of electrolyte and illumination conditions on photoanode performance
- Open Access
- 30 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-18
Synthesis and characterization of MoS2-carbon based materials for enhanced energy storage applications
The article delves into the synthesis and characterization of MoS2-carbon-based materials, holding promise for applications in supercapacitors and ion batteries. The synthesis process entails the preparation of MoS2 and its carbon hybrids through exfoliation, hydrothermal treatment, and subsequent pyrolysis. Various analytical techniques were employed to comprehensively examine the structural, compositional, and morphological properties of the resulting materials. The article explores the electrochemical performance of these electrode materials in supercapacitors and ion batteries (LiB, SiB, KiB). Electrochemical measurements were conducted in aqueous electrolyte for supercapacitors and various aprotic electrolytes for ion batteries. Results highlight the impact of the synthesis process on electrochemical performance, emphasizing factors such as capacitance, rate capability, and charge/discharge cycle performance. Hydrothermally treated MoS2-carbon exhibited a specific capacitance of approximately 150 F g-1 in supercapacitors, attributed to its high surface area and efficient charge storage mechanisms. Additionally, for Li-ion battery materials without hydrothermal treatment showed impressive capacity retention of around 88% after 500 charge-discharge cycles, starting with an initial specific capacity of about 920 mAh/g. Long-term stability was demonstrated in both supercapacitors and lithium-ion batteries, with minimal capacitance degradation even after extensive charge-discharge cycles. This research underscores the potential of MoS2-based materials as effective energy storage solutions.
- 30 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-18
Open AccessSynthesis and characterization of MoS2-carbon based materials for enhanced energy storage applications
The article delves into the synthesis and characterization of MoS2-carbon-based materials, holding promise for applications in supercapacitors and ion batteries. The synthesis process entails the preparation of MoS2 and its carbon hybrids through exfoliation, hydrothermal treatment, and subsequent pyrolysis. Various analytical techniques were employed to comprehensively examine the structural, compositional, and morphological properties of the resulting materials. The article explores the electrochemical performance of these electrode materials in supercapacitors and ion batteries (LiB, SiB, KiB). Electrochemical measurements were conducted in aqueous electrolyte for supercapacitors and various aprotic electrolytes for ion batteries. Results highlight the impact of the synthesis process on electrochemical performance, emphasizing factors such as capacitance, rate capability, and charge/discharge cycle performance. Hydrothermally treated MoS2-carbon exhibited a specific capacitance of approximately 150 F g-1 in supercapacitors, attributed to its high surface area and efficient charge storage mechanisms. Additionally, for Li-ion battery materials without hydrothermal treatment showed impressive capacity retention of around 88% after 500 charge-discharge cycles, starting with an initial specific capacity of about 920 mAh/g. Long-term stability was demonstrated in both supercapacitors and lithium-ion batteries, with minimal capacitance degradation even after extensive charge-discharge cycles. This research underscores the potential of MoS2-based materials as effective energy storage solutions.
- Open Access
- 23 October 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 92, 90-101
Hydrogen evolution reaction catalyzed by Co-based metal-organic frameworks and their derivatives
- 23 October 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 92, 90-101
Open AccessHydrogen evolution reaction catalyzed by Co-based metal-organic frameworks and their derivatives
- Open Access
- 2 December 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-13
The new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
In this work, ZnIn2S4 layers were obtained on fluorine doped tin oxide (FTO) glass and TiO2 nanotubes (TiO2NT) using a hydrothermal process as photoanodes for photoelectrochemical (PEC) water splitting. Then, samples were annealed and the effect of the annealing temperature was investigated. Optimization of the deposition process and annealing of ZnIn2S4 layers made it possible to obtain an FTO-based material generating a photocurrent of 1.2 mA cm−2 at 1.62 V vs. RHE in a neutral medium. In contrast, the highest photocurrent in the neutral electrolyte obtained for the TiO2NT-based photoanode reached 0.5 mA cm−2 at 1.62 V vs. RHE. In addition, the use of a strongly acidic electrolyte allowed the generated photocurrent by the TiO2NT-based photoanode to increase to 3.02 mA cm−2 at 0.31 V vs. RHE. Despite a weaker photoresponse in neutral electrolyte than the optimized FTO-based photoanode, the use of TiO2NT as a substrate allowed for a significant increase in the photoanode's operating time. After 2 h of illumination, the photocurrent response of the TiO2NT-based photoanode was 0.21 mA cm−2, which was 42% of the initial value. In contrast, the FTO-based photoanode after the same time generated a photocurrent of 0.02 mA cm−2 which was only 1% of the initial value. The results indicated that the use of TiO2 nanotubes as a substrate for ZnIn2S4 deposition increases the photoanode's long-term stability in photoelectrochemical water splitting. The proposed charge transfer mechanism suggested that the heterojunction between ZnIn2S4 and TiO2 played an important role in improving the stability of the material by supporting charge separation.
- 2 December 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-13
Open AccessThe new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
In this work, ZnIn2S4 layers were obtained on fluorine doped tin oxide (FTO) glass and TiO2 nanotubes (TiO2NT) using a hydrothermal process as photoanodes for photoelectrochemical (PEC) water splitting. Then, samples were annealed and the effect of the annealing temperature was investigated. Optimization of the deposition process and annealing of ZnIn2S4 layers made it possible to obtain an FTO-based material generating a photocurrent of 1.2 mA cm−2 at 1.62 V vs. RHE in a neutral medium. In contrast, the highest photocurrent in the neutral electrolyte obtained for the TiO2NT-based photoanode reached 0.5 mA cm−2 at 1.62 V vs. RHE. In addition, the use of a strongly acidic electrolyte allowed the generated photocurrent by the TiO2NT-based photoanode to increase to 3.02 mA cm−2 at 0.31 V vs. RHE. Despite a weaker photoresponse in neutral electrolyte than the optimized FTO-based photoanode, the use of TiO2NT as a substrate allowed for a significant increase in the photoanode's operating time. After 2 h of illumination, the photocurrent response of the TiO2NT-based photoanode was 0.21 mA cm−2, which was 42% of the initial value. In contrast, the FTO-based photoanode after the same time generated a photocurrent of 0.02 mA cm−2 which was only 1% of the initial value. The results indicated that the use of TiO2 nanotubes as a substrate for ZnIn2S4 deposition increases the photoanode's long-term stability in photoelectrochemical water splitting. The proposed charge transfer mechanism suggested that the heterojunction between ZnIn2S4 and TiO2 played an important role in improving the stability of the material by supporting charge separation.