Xiaochuan Liu
Xiaochuan Liu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Changqing Bai
Xi’an Jiaotong University, Xi’an 710049, People’s Republic of China
1 shared publication- Chao Hang
Aircraft Strength Research Institute
1 shared publication - Kai Liu
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
1 shared publication Kaixiang Li
National Key Laboratory of Strength and Structural Integrity, Aircraft Strength Research Institute of China, Xi’an 710065, People’s Republic of China
1 shared publication- Mingbo Tong
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
1 shared publication - Shaojie Guo
National Key Laboratory of Strength and Structural Integrity, Aircraft Strength Research Institute of China, Xi’an 710065, People’s Republic of China
1 shared publication
Latest Publications
- Open Access
An Analytical Model for High-Velocity Impacts of Flaky Projectile on Woven Composite Plates
Three-dimensional (3D) woven composites have good impact resistance and are expected to become the fan casing material for the next generation of turbofan engines. Conducting research on the performance of woven composite plates under high-velocity impact of flaky projectiles is of great significance for the containment design of the fan casing. Based on the principle of energy conservation, an analytical model for the high-velocity impact of flaky projectiles on carbon fiber woven composite plates was established for three typical failure modes: shear plugging, fiber failure, and momentum transfer. A segmented solution method combining analytical and numerical calculations was developed for the model. The critical penetration velocity of the plate obtained by the analytical method at different roll angles of the projectile is in good agreement with the experimental results, which verifies the accuracy of the analytical model. Moreover, the analytical results indicate that the critical penetration velocity of the plate increases first and then decreases with the roll angle of the projectile. Further energy conversion analysis points out that shear plugging is the main form of energy dissipation for woven composite plates, and the energy dissipation of shear plugging at a roll angle of 30° is higher than that at 0° and 60°. This elucidates the mechanism by which the roll angle of the projectile affects the critical penetration velocity of the plate from the perspective of energy dissipation.
Open AccessAn Analytical Model for High-Velocity Impacts of Flaky Projectile on Woven Composite Plates
Three-dimensional (3D) woven composites have good impact resistance and are expected to become the fan casing material for the next generation of turbofan engines. Conducting research on the performance of woven composite plates under high-velocity impact of flaky projectiles is of great significance for the containment design of the fan casing. Based on the principle of energy conservation, an analytical model for the high-velocity impact of flaky projectiles on carbon fiber woven composite plates was established for three typical failure modes: shear plugging, fiber failure, and momentum transfer. A segmented solution method combining analytical and numerical calculations was developed for the model. The critical penetration velocity of the plate obtained by the analytical method at different roll angles of the projectile is in good agreement with the experimental results, which verifies the accuracy of the analytical model. Moreover, the analytical results indicate that the critical penetration velocity of the plate increases first and then decreases with the roll angle of the projectile. Further energy conversion analysis points out that shear plugging is the main form of energy dissipation for woven composite plates, and the energy dissipation of shear plugging at a roll angle of 30° is higher than that at 0° and 60°. This elucidates the mechanism by which the roll angle of the projectile affects the critical penetration velocity of the plate from the perspective of energy dissipation.
- 1 September 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (9) , 095026
Asymmetric bandgaps for bidirectional vibration suppression in metamaterial beams
This paper proposes a finite-length metamaterial beam (FLMB) based on local resonance, featuring two distinct bandgaps. The impact of forward and backward wave propagation on the dispersion characteristics of the proposed FLMB is investigated using numerical methods alongside experimental validation. Transfer matrix method (TMM) models incorporating the influence of wave propagation direction are developed to predict the band structure and frequency response functions. Experimental results align well with both TMM and finite element method simulations. Collectively, they demonstrate that the stop-band under forward wave propagation is continuous and broad, whereas the stop-band under backward wave propagation is segmented. This directional difference originates from the reversal in interaction moments between the primary beam and local resonators. Analysis of the TMM-derived band structure reveals that forward and backward transport properties are predominantly governed by the suppression capability concerning evanescent waves. These asymmetric transport properties become markedly distinct for a limited number of unitcells but converge as the number approaches infinity. The effects of resonator parameters on the FLMB’s asymmetric bandgaps characteristics are also discussed.
- 1 September 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (9) , 095026
Asymmetric bandgaps for bidirectional vibration suppression in metamaterial beams
This paper proposes a finite-length metamaterial beam (FLMB) based on local resonance, featuring two distinct bandgaps. The impact of forward and backward wave propagation on the dispersion characteristics of the proposed FLMB is investigated using numerical methods alongside experimental validation. Transfer matrix method (TMM) models incorporating the influence of wave propagation direction are developed to predict the band structure and frequency response functions. Experimental results align well with both TMM and finite element method simulations. Collectively, they demonstrate that the stop-band under forward wave propagation is continuous and broad, whereas the stop-band under backward wave propagation is segmented. This directional difference originates from the reversal in interaction moments between the primary beam and local resonators. Analysis of the TMM-derived band structure reveals that forward and backward transport properties are predominantly governed by the suppression capability concerning evanescent waves. These asymmetric transport properties become markedly distinct for a limited number of unitcells but converge as the number approaches infinity. The effects of resonator parameters on the FLMB’s asymmetric bandgaps characteristics are also discussed.
- Open Access
- 2 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (23) , 12921
Influence of Cargo Luggage on the Vertical Drop Crashworthiness of Aircraft Mid-Fuselage Section
The evaluation of structural crashworthiness is important for the development of civil aircraft. In this study, cargo luggage was considered in the vertical drop simulation of an aircraft mid-fuselage section. First, quasi-static compression tests on three types of luggage made of different materials were conducted. Then, a finite element model (FEM) of the cargo luggage was developed with a crushable foam material in LS-PrePost4.5 software. The finite element analysis results of the luggage made of different materials were consistent with the corresponding compression experiments. Secondly, the FEM of the mid-fuselage section was established without cargo luggage. The simulated displacement and acceleration of the fuselage section were consistent with the test results. Finally, the influences of cargo luggage on the fuselage vertical drop response were studied with the FEM considering both the fuselage structure and cargo luggage. Compared with the responses of the fuselage without cargo luggage, the cargo luggage could reduce the deformation of the cargo bay and maintain the integrity of the passenger living space in the cabin at the vertical velocity of 6 m/s, even though the initial kinetic energy was higher.
- 2 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (23) , 12921
Open AccessInfluence of Cargo Luggage on the Vertical Drop Crashworthiness of Aircraft Mid-Fuselage Section
The evaluation of structural crashworthiness is important for the development of civil aircraft. In this study, cargo luggage was considered in the vertical drop simulation of an aircraft mid-fuselage section. First, quasi-static compression tests on three types of luggage made of different materials were conducted. Then, a finite element model (FEM) of the cargo luggage was developed with a crushable foam material in LS-PrePost4.5 software. The finite element analysis results of the luggage made of different materials were consistent with the corresponding compression experiments. Secondly, the FEM of the mid-fuselage section was established without cargo luggage. The simulated displacement and acceleration of the fuselage section were consistent with the test results. Finally, the influences of cargo luggage on the fuselage vertical drop response were studied with the FEM considering both the fuselage structure and cargo luggage. Compared with the responses of the fuselage without cargo luggage, the cargo luggage could reduce the deformation of the cargo bay and maintain the integrity of the passenger living space in the cabin at the vertical velocity of 6 m/s, even though the initial kinetic energy was higher.