Yao Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yao Sun has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Li Yu
Nanjing University of Aeronautics and Astronautics
5 shared publications - Zhuoran Zhang
Nanjing University of Aeronautics and Astronautics
5 shared publications - Xu Chen
Jiangsu Key Laboratory of New Energy Generation and Power Conversion, Nanjing University of Aeronautics and Astronautics, Nanjing, China
4 shared publications - Yongtao Guan
Center for More-Electric-Aircraft Power System, Nanjing University of Aeronautics and Astronautics, Nanjing, China
3 shared publications - Guangyuan Hu
Center for More-Electric-Aircraft Power System, Nanjing University of Aeronautics and Astronautics, Nanjing, China
2 shared publications - Chuang Liu
College of Automation Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication
Latest Publications
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 2599-2611
Commutation Angle Closed-Loop-Based Average Torque Control Method of High-Speed Doubly Salient Electromagnetic Motor for Torque Capability Improvement
The effect of the field current and commutation angle parameters on the average torque of a doubly salient electromagnetic motor (DSEM) is highly mutually coupled at high-speed operation. Hence, it is hard for the conventional methods to realize the simultaneous adjustment of field current and commutation angle to fully use the torque capability of the DSEM at high-speed operation. In this article, a commutation angle closed-loop (CAC) based average torque control method is proposed. First, the effect of the field current and commutation angle parameters on the average torque is analyzed. The characteristics of optimal commutation angle parameters are derived, and the CAC method is proposed to adjust the commutation angle parameters by aligning the phase current intersections with phase back electromotive force (EMF) intersections adaptively. Then, the relationship between the field current and average torque is investigated under the proposed CAC method. On this basis, the variable-step perturbation and observation algorithm and average torque control are proposed to adjust the field current by maximizing the average torque. Finally, the proposed CAC-based average torque control method is verified on the high-speed DSEM drive system. The experimental results indicate that the proposed control method can adaptively obtain the optimal commutation angle parameters and field current simultaneously and realize the maximum torque operation of the high-speed DSEM drive system.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 2599-2611
Commutation Angle Closed-Loop-Based Average Torque Control Method of High-Speed Doubly Salient Electromagnetic Motor for Torque Capability Improvement
The effect of the field current and commutation angle parameters on the average torque of a doubly salient electromagnetic motor (DSEM) is highly mutually coupled at high-speed operation. Hence, it is hard for the conventional methods to realize the simultaneous adjustment of field current and commutation angle to fully use the torque capability of the DSEM at high-speed operation. In this article, a commutation angle closed-loop (CAC) based average torque control method is proposed. First, the effect of the field current and commutation angle parameters on the average torque is analyzed. The characteristics of optimal commutation angle parameters are derived, and the CAC method is proposed to adjust the commutation angle parameters by aligning the phase current intersections with phase back electromotive force (EMF) intersections adaptively. Then, the relationship between the field current and average torque is investigated under the proposed CAC method. On this basis, the variable-step perturbation and observation algorithm and average torque control are proposed to adjust the field current by maximizing the average torque. Finally, the proposed CAC-based average torque control method is verified on the high-speed DSEM drive system. The experimental results indicate that the proposed control method can adaptively obtain the optimal commutation angle parameters and field current simultaneously and realize the maximum torque operation of the high-speed DSEM drive system.
- 3 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 2097-2107
Design and Analysis of In-Slot Sleeve Direct Oil Cooling Method for Reluctance Machines
Due to the structural constraints of the salient-pole rotor and narrow air gap in reluctance machines, conventional winding direct cooling methods cannot be directly applied, limiting a further improvement in power density. To address this challenge, this article proposes a novel direct oil cooling solution employing an in-slot sleeve (ISS) structure. The in-slot portion is enclosed by the ISS, while the electric machine ends are sealed with the end sleeve. These two components are combined through the stator end plate to form a complete enclosed cooling channel. This arrangement separates the windings from both stator and rotor components without occupying the air gap space, enabling direct winding cooling. This article employs a 45 kW ISS direct oil-cooled doubly salient electromagnetic machine (DSEM) as the test case. A refined thermal network model is developed, accounting for loss distribution characteristics of the DSEM, and the influence of the ISS on winding cooling performance is analyzed. An experimental platform validates prolonged operation at 3 L/min flow rate, 65 ° C oil temperature, and 22.1 A/mm2 current density, confirming the accuracy of the thermal model. Furthermore, thermal simulation results demonstrate that the maximum sustainable current density reaches 27.1 A/mm2 at this flow rate.
- 3 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (2) , 2097-2107
Design and Analysis of In-Slot Sleeve Direct Oil Cooling Method for Reluctance Machines
Due to the structural constraints of the salient-pole rotor and narrow air gap in reluctance machines, conventional winding direct cooling methods cannot be directly applied, limiting a further improvement in power density. To address this challenge, this article proposes a novel direct oil cooling solution employing an in-slot sleeve (ISS) structure. The in-slot portion is enclosed by the ISS, while the electric machine ends are sealed with the end sleeve. These two components are combined through the stator end plate to form a complete enclosed cooling channel. This arrangement separates the windings from both stator and rotor components without occupying the air gap space, enabling direct winding cooling. This article employs a 45 kW ISS direct oil-cooled doubly salient electromagnetic machine (DSEM) as the test case. A refined thermal network model is developed, accounting for loss distribution characteristics of the DSEM, and the influence of the ISS on winding cooling performance is analyzed. An experimental platform validates prolonged operation at 3 L/min flow rate, 65 ° C oil temperature, and 22.1 A/mm2 current density, confirming the accuracy of the thermal model. Furthermore, thermal simulation results demonstrate that the maximum sustainable current density reaches 27.1 A/mm2 at this flow rate.
- 10 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16431-16442
Optimal Excitation Angles Analysis Based on the SRM Quasi-Linear Normalized Model for Enhanced Overall Performance
This article evaluates the comprehensive performance of switched reluctance motors (SRMs) using three key metrics: torque per ampere, average torque, and torque ripple, which cannot be simultaneously optimized at the same excitation angle. Traditional analytical methods for optimizing excitation angles (turn-on and turn-off angles) focus solely on maximizing torque per ampere, resulting in complex formulas with limited general applicability. To overcome these limitations and ensure high-performance operation of the SRM across the entire torque-speed range, a generalized SRM quasi-linear normalized model is proposed, addressing the tradeoff between model accuracy and complexity. A multiobjective function is developed to coordinate the three performance metrics, and universal analytical formulas for optimal excitation angles are derived. The excitation angle controller requires only real-time detection of speed and reference current, enabling simple implementation. The precision and generality of the derived expressions are validated through comparisons with traditional finite-element methods using 12/8 three-phase and 8/6 four-phase SRMs. Simultaneously, considering the fringing effect and the back electromotive force in the low-inductance region, the current reference compensation in single pulse mode ensures that the target current peak is achieved. Finally, steady-state and dynamic experiments on a 12/8 three-phase prototype confirm the effectiveness of the optimal excitation angle formulas.
- 10 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16431-16442
Optimal Excitation Angles Analysis Based on the SRM Quasi-Linear Normalized Model for Enhanced Overall Performance
This article evaluates the comprehensive performance of switched reluctance motors (SRMs) using three key metrics: torque per ampere, average torque, and torque ripple, which cannot be simultaneously optimized at the same excitation angle. Traditional analytical methods for optimizing excitation angles (turn-on and turn-off angles) focus solely on maximizing torque per ampere, resulting in complex formulas with limited general applicability. To overcome these limitations and ensure high-performance operation of the SRM across the entire torque-speed range, a generalized SRM quasi-linear normalized model is proposed, addressing the tradeoff between model accuracy and complexity. A multiobjective function is developed to coordinate the three performance metrics, and universal analytical formulas for optimal excitation angles are derived. The excitation angle controller requires only real-time detection of speed and reference current, enabling simple implementation. The precision and generality of the derived expressions are validated through comparisons with traditional finite-element methods using 12/8 three-phase and 8/6 four-phase SRMs. Simultaneously, considering the fringing effect and the back electromotive force in the low-inductance region, the current reference compensation in single pulse mode ensures that the target current peak is achieved. Finally, steady-state and dynamic experiments on a 12/8 three-phase prototype confirm the effectiveness of the optimal excitation angle formulas.
- 26 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (4) , 4542-4556
Improved Flux Weakening Control of Doubly Salient Electromagnetic Motor Considering d-and q-Axis Voltage Harmonics
The parallel stator poles structure and concentrated field winding configuration of the doubly salient electromagnetic motor (DSEM) lead to the asymmetric three-phase flux paths and thus causing the significant d -axis and q -axis voltage harmonics. In the conventional flux weakening control methods, these d -axis and q -axis voltage harmonics are not considered, which will cause the deviation between the computed voltage and the actual voltage and reduce the dc-link voltage utilization. In this article, an improved flux weakening control method considering the d -axis and q -axis voltage harmonics induced by the asymmetric three-phase flux paths is proposed for the DSEM. First, the asymmetric three-phase flux paths of the DSEM are analyzed in this article. Then, the voltage equation considering the asymmetric three-phase flux paths is derived and verified. The current and voltage constraint are constructed and the reference current curves at different speeds are obtained through the proposed offline method. Finally, the proposed flux weakening control method is implemented on the 12/8-pole DSEM drive system. The experimental results indicate that the proposed flux weakening control method can improve the dc-link voltage utilization, effectively extend the constant torque region, and enhance the output power and torque capability of the DSEM drive system.
- 26 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (4) , 4542-4556
Improved Flux Weakening Control of Doubly Salient Electromagnetic Motor Considering d-and q-Axis Voltage Harmonics
The parallel stator poles structure and concentrated field winding configuration of the doubly salient electromagnetic motor (DSEM) lead to the asymmetric three-phase flux paths and thus causing the significant d -axis and q -axis voltage harmonics. In the conventional flux weakening control methods, these d -axis and q -axis voltage harmonics are not considered, which will cause the deviation between the computed voltage and the actual voltage and reduce the dc-link voltage utilization. In this article, an improved flux weakening control method considering the d -axis and q -axis voltage harmonics induced by the asymmetric three-phase flux paths is proposed for the DSEM. First, the asymmetric three-phase flux paths of the DSEM are analyzed in this article. Then, the voltage equation considering the asymmetric three-phase flux paths is derived and verified. The current and voltage constraint are constructed and the reference current curves at different speeds are obtained through the proposed offline method. Finally, the proposed flux weakening control method is implemented on the 12/8-pole DSEM drive system. The experimental results indicate that the proposed flux weakening control method can improve the dc-link voltage utilization, effectively extend the constant torque region, and enhance the output power and torque capability of the DSEM drive system.
- 4 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 10221-10234
A Variable Sampling-Frequency-Based Commutation Delay Compensation Method for High-Speed Doubly Salient Motor Considering Speed Fluctuation
The doubly salient motor (DSM) is a suitable candidate for the high-speed drive system due to its robust structure and adjustable magnet field. However, the commutation delay at high-speed operation will deteriorate the current performance and thereby degrade the torque capability of the DSM drive system. In this article, the commutation delay compensation (CDC) method based on variable sampling frequency is proposed for the high-speed DSM drive system. First, the production mechanism of commutation delay is analyzed and the commutation delay is classified into two categories. Then, in the proposed CDC method, the angle difference between the sampled rotor position and the given commutation angle is calculated. The sampling frequency is adjusted in real time based on the angle difference and the criterion considering the influence of speed fluctuation. The commutation delay characteristics are analyzed through simulation results. Finally, the proposed CDC method is implemented on a high-speed DSM drive system. The experiment of the proposed CDC method is carried out on the condition of steady-state, different speeds, reference speed step change, and variable load torque. The experimental results indicate that the proposed CDC method can effectively compensate the commutation delay and enhance the torque capability of the high-speed DSM drive system.
- 4 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 10221-10234
A Variable Sampling-Frequency-Based Commutation Delay Compensation Method for High-Speed Doubly Salient Motor Considering Speed Fluctuation
The doubly salient motor (DSM) is a suitable candidate for the high-speed drive system due to its robust structure and adjustable magnet field. However, the commutation delay at high-speed operation will deteriorate the current performance and thereby degrade the torque capability of the DSM drive system. In this article, the commutation delay compensation (CDC) method based on variable sampling frequency is proposed for the high-speed DSM drive system. First, the production mechanism of commutation delay is analyzed and the commutation delay is classified into two categories. Then, in the proposed CDC method, the angle difference between the sampled rotor position and the given commutation angle is calculated. The sampling frequency is adjusted in real time based on the angle difference and the criterion considering the influence of speed fluctuation. The commutation delay characteristics are analyzed through simulation results. Finally, the proposed CDC method is implemented on a high-speed DSM drive system. The experiment of the proposed CDC method is carried out on the condition of steady-state, different speeds, reference speed step change, and variable load torque. The experimental results indicate that the proposed CDC method can effectively compensate the commutation delay and enhance the torque capability of the high-speed DSM drive system.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 13895-13906
An Improved Direct Instantaneous Torque Control of Two-Segment Twisted-Rotor Doubly Salient Motor for Torque Capability Enhancement
The direct instantaneous torque control (DITC) method is an effective way to suppress the torque ripple of doubly salient motor (DSM). However, there is the inevitable phase current peak in the conventional DITC method, which increases the current stress of the power switches and degrades the torque capability of the DSM. In this paper, an improved DITC method is proposed based on the optimal torque sharing ratio. Firstly, the maximum torque characteristics of two-segment twisted-rotor DSM are obtained through the finite element method. The optimal torque sharing ratio and the ideal phase current waveform are deduced based on the maximum torque characteristics of two parts of two-segment twisted-rotor DSM, which have 180° electrical angle difference. Then, by sharing the total reference torque to two parts according to optimal torque sharing ratio, the operation principle of the proposed DITC method is derived. Finally, the proposed DITC method is implemented on the 12/8-pole two-segment twisted-rotor DSM drive system. The performance of the proposed DITC method under different commutation angle parameters, different speeds, and reference speed step change are demonstrated through experimental results. The experimental results indicate that the proposed DITC method can suppress the peak current and enhance the torque capability of two-segment twisted-rotor DSM while guaranteeing low torque ripple operation.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (11) , 13895-13906
An Improved Direct Instantaneous Torque Control of Two-Segment Twisted-Rotor Doubly Salient Motor for Torque Capability Enhancement
The direct instantaneous torque control (DITC) method is an effective way to suppress the torque ripple of doubly salient motor (DSM). However, there is the inevitable phase current peak in the conventional DITC method, which increases the current stress of the power switches and degrades the torque capability of the DSM. In this paper, an improved DITC method is proposed based on the optimal torque sharing ratio. Firstly, the maximum torque characteristics of two-segment twisted-rotor DSM are obtained through the finite element method. The optimal torque sharing ratio and the ideal phase current waveform are deduced based on the maximum torque characteristics of two parts of two-segment twisted-rotor DSM, which have 180° electrical angle difference. Then, by sharing the total reference torque to two parts according to optimal torque sharing ratio, the operation principle of the proposed DITC method is derived. Finally, the proposed DITC method is implemented on the 12/8-pole two-segment twisted-rotor DSM drive system. The performance of the proposed DITC method under different commutation angle parameters, different speeds, and reference speed step change are demonstrated through experimental results. The experimental results indicate that the proposed DITC method can suppress the peak current and enhance the torque capability of two-segment twisted-rotor DSM while guaranteeing low torque ripple operation.
- 15 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automatic Control
- Vol. 62 (3) , 1530-1536
MMSE State Estimation Approach for Linear Discrete-Time Systems With Time-Delay and Multi-Error Measurements
This technical note focuses on designing a novel optimal estimation approach for linear discrete-time systems with time-delay and multi-error measurements, inspired by the measurement demands of the Five-hundred-meter Aperture Spherical radio Telescope. Measurement errors from different measurement channels, which are considered equal in many previous estimation methods, are usually negatively correlated with time-delays. Measurements with higher time-delays usually have less errors than the ones with lower delays. Our approach improves the estimation accuracy by decreasing the usage rate of measurements with larger errors. To prove the optimality of the approach in the minimum mean square error sense, a derivation procedure is presented. A numerical example and comparison are also given to demonstrate the feasibility and advantage of the proposed approach.
- 15 June 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automatic Control
- Vol. 62 (3) , 1530-1536
MMSE State Estimation Approach for Linear Discrete-Time Systems With Time-Delay and Multi-Error Measurements
This technical note focuses on designing a novel optimal estimation approach for linear discrete-time systems with time-delay and multi-error measurements, inspired by the measurement demands of the Five-hundred-meter Aperture Spherical radio Telescope. Measurement errors from different measurement channels, which are considered equal in many previous estimation methods, are usually negatively correlated with time-delays. Measurements with higher time-delays usually have less errors than the ones with lower delays. Our approach improves the estimation accuracy by decreasing the usage rate of measurements with larger errors. To prove the optimality of the approach in the minimum mean square error sense, a derivation procedure is presented. A numerical example and comparison are also given to demonstrate the feasibility and advantage of the proposed approach.
- 22 October 2012
- Published by Springer Nature in Science China Mathematics
- Vol. 56 (4) , 745-756
A new proof for the correctness of the F5 algorithm
- 22 October 2012
- Published by Springer Nature in Science China Mathematics
- Vol. 56 (4) , 745-756
A new proof for the correctness of the F5 algorithm