Yinghao Liao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yinghao Liao has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Bing Wang
School of Mechanical Engineering, Shandong University, Jinan, PR China
1 shared publication - Changxi Zhao
Beijing Spacecrafts, China Academy of Space Technology, Beijing 100094, China
1 shared publication - Dian Wang
The Institute of Technological Sciences, Wuhan University, Wuhan 430072, China
1 shared publication - Liyan Zheng
Beijing Spacecrafts, Beijing 100094, China
1 shared publication - Longxu Yao
Shandong University School of Mechanical Engineering, State Key Laboratory of Advanced Equipment and Technology for Metal Forming Jinan 250061 , China
1 shared publication - Xiaoming Hao
Beijing Spacecrafts, Beijing 100094, China
1 shared publication
Latest Publications
- Open Access
- 6 December 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (12) , 2209
Ultrasonic-Vibration-Assisted Waterjet Drilling of [0/45/−45/90]2s Carbon-Fiber-Reinforced Polymer Laminates
The pure waterjet (WJ) drilling process of carbon-fiber-reinforced polymer (CFRP) laminates causes damage, such as tears and delamination, leading to poor-quality hole-wall. Ultrasonic-vibration-assisted technology can improve the quality of hole walls and repair such damage, particularly the delamination of CFRP laminates. In this study, we conducted a numerical and experimental investigation of a high-pressure pure WJ drilling process of CFRP laminates performed using ultrasonic vibration to improve the delamination phenomena of the pure WJ drilling process. An explicit dynamic model using the smoothed particle hydrodynamics method was employed to simulate the ultrasonic-vibration-assisted WJ drilling of CFRP laminates and ascertain the optimal drilling performance. Thereafter, WJ drilling experiments were conducted to verify the numerical simulation. The results illustrate that the employment of ultrasonic vibration significantly increased the material removal rate by approximately 20%. Moreover, the water-wedging action that induces the propagation of delamination was weakened with an increase in the amplitude of the ultrasonic vibration. The hole-wall quality was optimal with the following drilling parameters: amplitude, 10 μm; frequency, 20 kHz; and WJ velocity, 900 m/s. The delamination zone length was only 0.19 mm and was reduced by 85.6% compared with the values obtained using non-assisted WJ drilling.
- 6 December 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (12) , 2209
Open AccessUltrasonic-Vibration-Assisted Waterjet Drilling of [0/45/−45/90]2s Carbon-Fiber-Reinforced Polymer Laminates
The pure waterjet (WJ) drilling process of carbon-fiber-reinforced polymer (CFRP) laminates causes damage, such as tears and delamination, leading to poor-quality hole-wall. Ultrasonic-vibration-assisted technology can improve the quality of hole walls and repair such damage, particularly the delamination of CFRP laminates. In this study, we conducted a numerical and experimental investigation of a high-pressure pure WJ drilling process of CFRP laminates performed using ultrasonic vibration to improve the delamination phenomena of the pure WJ drilling process. An explicit dynamic model using the smoothed particle hydrodynamics method was employed to simulate the ultrasonic-vibration-assisted WJ drilling of CFRP laminates and ascertain the optimal drilling performance. Thereafter, WJ drilling experiments were conducted to verify the numerical simulation. The results illustrate that the employment of ultrasonic vibration significantly increased the material removal rate by approximately 20%. Moreover, the water-wedging action that induces the propagation of delamination was weakened with an increase in the amplitude of the ultrasonic vibration. The hole-wall quality was optimal with the following drilling parameters: amplitude, 10 μm; frequency, 20 kHz; and WJ velocity, 900 m/s. The delamination zone length was only 0.19 mm and was reduced by 85.6% compared with the values obtained using non-assisted WJ drilling.