Joanna Nseir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Joanna Nseir has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Nicolas Boissonnade
4 shared publicationsElsy Saloumi
3 shared publications- Hugues Somja
INSA de Rennes
3 shared publications Marielle Hayeck
3 shared publications- Nicolas Boissonnade
Université Laval
2 shared publications - Alexandru Chira
Institute of Construction and Environmental Technologies iTEC, University of Applied Sciences and Arts Western Switzerland HES-SO
1 shared publication
Latest Publications
- 10 August 2025
- Published by Springer Nature
- p. 41-57
From Scan to Sustainability: A Comprehensive Framework for Retrofitting Steel Roofs
- 10 August 2025
- Published by Springer Nature
- p. 41-57
From Scan to Sustainability: A Comprehensive Framework for Retrofitting Steel Roofs
- 21 January 2024
- Published by Elsevier in Thin-Walled Structures
- Vol. 197
Design of cellular steel beams subjected to lateral torsional buckling
- 21 January 2024
- Published by Elsevier in Thin-Walled Structures
- Vol. 197
Design of cellular steel beams subjected to lateral torsional buckling
- 19 November 2023
- Published by Elsevier in Thin-Walled Structures
- Vol. 195
Experimental and numerical investigations towards the lateral torsional buckling of cellular steel beams
- 19 November 2023
- Published by Elsevier in Thin-Walled Structures
- Vol. 195
Experimental and numerical investigations towards the lateral torsional buckling of cellular steel beams
- 25 June 2021
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 64 (3) , 1367-1383
Topology optimization of load-bearing capacity
- 25 June 2021
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 64 (3) , 1367-1383
Topology optimization of load-bearing capacity
- 1 April 2020
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 167
Slenderness-based design criteria to allow for the plastic analysis of tubular beams
- 1 April 2020
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 167
Slenderness-based design criteria to allow for the plastic analysis of tubular beams
- 1 July 2018
- Published by Elsevier in Thin-Walled Structures
- Vol. 128, 92-107
Experimental characterization of steel tubular beam-columns resistance by means of the Overall Interaction Concept
- 1 July 2018
- Published by Elsevier in Thin-Walled Structures
- Vol. 128, 92-107
Experimental characterization of steel tubular beam-columns resistance by means of the Overall Interaction Concept
- 1 August 2017
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 135, 199-212
An Overall Interaction Concept for an alternative approach to steel members design
- 1 August 2017
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 135, 199-212
An Overall Interaction Concept for an alternative approach to steel members design
- 1 July 2014
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 167 (7) , 436-444
Design of cellular beams against lateral torsional buckling
The behaviour of so-called ‘cellular members' against lateral torsional buckling is investigated. These beams comprise regularly spaced web openings, and are especially used for their high resistance-to-weight ratio, the possibility of integrating service pipes within their height, and for aesthetic reasons. Such profiles usually exhibit a complex behaviour and many potential failure modes, including interactional local/global instability modes. Regarding global instability, members are usually designed by means of approximate design rules, which often lead to an unduly conservative girder, with beams sometimes showing up to 150% resistance reserve. This research work aims at improving this situation, through development of adequate design formulas. Both experimental and extensive numerical parametric studies are undertaken; a series of three full-scale tests is first performed, with the intention of using them to validate the derived finite-element models. Because the numerical models show very good agreement with the tests, they are then further used to gather a large set of numerical reference results where many parameters are varied: relative slenderness, steel grades, cross-sectional dimensions, bending moment distributions and the relative size of the openings. Finally, a new set of dedicated design rules is derived, which is demonstrated to be accurate and economic while leading to safe estimates of resistance when compared to all reference results.
- 1 July 2014
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 167 (7) , 436-444
Design of cellular beams against lateral torsional buckling
The behaviour of so-called ‘cellular members' against lateral torsional buckling is investigated. These beams comprise regularly spaced web openings, and are especially used for their high resistance-to-weight ratio, the possibility of integrating service pipes within their height, and for aesthetic reasons. Such profiles usually exhibit a complex behaviour and many potential failure modes, including interactional local/global instability modes. Regarding global instability, members are usually designed by means of approximate design rules, which often lead to an unduly conservative girder, with beams sometimes showing up to 150% resistance reserve. This research work aims at improving this situation, through development of adequate design formulas. Both experimental and extensive numerical parametric studies are undertaken; a series of three full-scale tests is first performed, with the intention of using them to validate the derived finite-element models. Because the numerical models show very good agreement with the tests, they are then further used to gather a large set of numerical reference results where many parameters are varied: relative slenderness, steel grades, cross-sectional dimensions, bending moment distributions and the relative size of the openings. Finally, a new set of dedicated design rules is derived, which is demonstrated to be accurate and economic while leading to safe estimates of resistance when compared to all reference results.