Xiaomin Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaomin Hu has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Jingjing Dong
National Engineering Research Center for Efficient Utilization of Soil and Fertilizer Resources, College of Resources and Environment, Shandong Agricultural University, Taian 271018, China
2 shared publications - Min Zhang
National Engineering Laboratory for Efficient Utilization of Soil and Fertilizer Resources, College of Recourses and Environment, College of Chemistry and Material Science, College of Life Sciences, Shandong Agricultural University, Taian 271018, China; State Key Laboratory of Nutrition Resources Integrated Utilization, Kingenta Ecological Engineering Group Co., Ltd., Linshu 276700, China
2 shared publications - Zhiguang Liu
National Engineering Research Center for Efficient Utilization of Soil and Fertilizer Resources, College of Recourses and Environment, Shandong Agricultural University, Taian, 271018, China
2 shared publications - Baishan Liu
National Engineering Research Center for Efficient Utilization of Soil and Fertilizer Resources, College of Resources and Environment, Shandong Agricultural University, Taian 271018, China
1 shared publication - Changxin Yu
National Engineering Research Center for Efficient Utilization of Soil and Fertilizer Resources, National Engineering & Technology Research Center for Slow and Controlled Release Fertilizers, College of Resources and Environment, Shandong Agricultural University, Tai’an 271018, China
1 shared publication - Heping Chen
National Engineering Research Center for Efficient Utilization of Soil and Fertilizer Resources, College of Resources and Environment, Shandong Agricultural University, Taian 271018, China
1 shared publication
Latest Publications
- Open Access
Lignin-Modified Petrochemical-Source Polyester Polyurethane Enhances Nutrient Release Performance of Coated Urea
The development of controlled-release fertilizers (CRFs) has faced significant challenges due to high hydrophilicity and short release lifespan of bio-based materials, as well as non-renewable and high cost of polyester polyols (PPs). In this study, lignin-based polyols (LPs) and PPs were modified to form a cross-linked polymer film on the surface of urea through an in situ reaction. This approach effectively balanced the slow-release ability and environmental protection of controlled-release fertilizer films. A two-factor, five-level orthogonal test was designed for the mass ratio of lignin/polyester polyol and polyol/polyaryl polymethylene isocyanate (PAPI), comprising a total of 25 treatments. The results indicated that the appropriateness of lignin polyols increased the hydrogen bond content of polyurethane membrane, improved the mechanical strength of the fertilizer membrane shell, and effectively reduced friction losses during storage and transportation. Moreover, optimizing the polyol-to-PAPI ratio minimized coating porosity, produced a smoother and denser surface, and prolonged the nitrogen release period. When the lignin polyol dosage was 25% and the polyol to PAPI ratio was 1:2, the nitrogen release time of the prepared coated urea extended to 32 days, which was 3.5 times longer than that of lignin polyurethane coated urea (7 days). The incorporation of lignin and the optimal ratio of coating materials significantly improved the controlled-release efficiency of coated fertilizer, providing theoretical support for the sustainable agricultural application of biomass.
Open AccessLignin-Modified Petrochemical-Source Polyester Polyurethane Enhances Nutrient Release Performance of Coated Urea
The development of controlled-release fertilizers (CRFs) has faced significant challenges due to high hydrophilicity and short release lifespan of bio-based materials, as well as non-renewable and high cost of polyester polyols (PPs). In this study, lignin-based polyols (LPs) and PPs were modified to form a cross-linked polymer film on the surface of urea through an in situ reaction. This approach effectively balanced the slow-release ability and environmental protection of controlled-release fertilizer films. A two-factor, five-level orthogonal test was designed for the mass ratio of lignin/polyester polyol and polyol/polyaryl polymethylene isocyanate (PAPI), comprising a total of 25 treatments. The results indicated that the appropriateness of lignin polyols increased the hydrogen bond content of polyurethane membrane, improved the mechanical strength of the fertilizer membrane shell, and effectively reduced friction losses during storage and transportation. Moreover, optimizing the polyol-to-PAPI ratio minimized coating porosity, produced a smoother and denser surface, and prolonged the nitrogen release period. When the lignin polyol dosage was 25% and the polyol to PAPI ratio was 1:2, the nitrogen release time of the prepared coated urea extended to 32 days, which was 3.5 times longer than that of lignin polyurethane coated urea (7 days). The incorporation of lignin and the optimal ratio of coating materials significantly improved the controlled-release efficiency of coated fertilizer, providing theoretical support for the sustainable agricultural application of biomass.
- Open Access
Soybean-Oil-Modified Petrochemical-Source Polyester Polyurethane Improves the Nutrient Release Performance of Coated Urea
Due to the difficult degradation and high cost of polyester polyols (PPs), their further development in controlled-release fertilizers (CRFs) has been limited. It was of great significance to partially substitute PPs with soybean oil polyols (SOPs) in the preparation of CRFs, which can adjust the proportion of substitution to balance the nutrient release period and membrane degradability. And it is possible to adjust the nitrogen release curve and prepare coated urea with different release days without changing the coating thickness. In this study, a two-factor five-level interaction experiment was designed with different SOP addition ratios (70%, 60%, 50%, 40%, and 30%) and mass ratios of polyols to PAPI (1:1.2; 1:1; 1.2:1; 1.4:1; and 1.6:1). In 25 groups of soybean-oil-modified polyester polyurethane-coated urea (SMPCU) treatments, with the increase in SOP, the thermal decomposition performance of the coated urea was improved, and the residual ash contents of the coating material was reduced. The coating surface was made smoother and denser with a reasonable ratio of polyols to PAPI, preventing the release of non-film-forming substances. When the proportion of soybean oil was 60% and the ratio of polyols to PAPI was 1.2:1, the N release days of the prepared SMPCU reached 137 days. Compared to soybean-oil polyol-coated urea (SOPCU) and polyester polyol-coated urea (PPCU), the nitrogen release days increased by 73.42% (79 days) and 234.15% (41 days), respectively. The ratio of polyols to polyaryl polymethylene isocyanate (PAPI) was explored, as well as the effect of polyol composition on coatings, and prepared SMPCUs with different nitrogen release days. According to the growth needs of crops and soil environmental characteristics, adjusting the proportion of coating materials, prolonging or shortening the nitrogen fertilizer release time, meets the nutritional needs of crops under different planting systems and provides conditions for farmers to plant different crops.
Open AccessSoybean-Oil-Modified Petrochemical-Source Polyester Polyurethane Improves the Nutrient Release Performance of Coated Urea
Due to the difficult degradation and high cost of polyester polyols (PPs), their further development in controlled-release fertilizers (CRFs) has been limited. It was of great significance to partially substitute PPs with soybean oil polyols (SOPs) in the preparation of CRFs, which can adjust the proportion of substitution to balance the nutrient release period and membrane degradability. And it is possible to adjust the nitrogen release curve and prepare coated urea with different release days without changing the coating thickness. In this study, a two-factor five-level interaction experiment was designed with different SOP addition ratios (70%, 60%, 50%, 40%, and 30%) and mass ratios of polyols to PAPI (1:1.2; 1:1; 1.2:1; 1.4:1; and 1.6:1). In 25 groups of soybean-oil-modified polyester polyurethane-coated urea (SMPCU) treatments, with the increase in SOP, the thermal decomposition performance of the coated urea was improved, and the residual ash contents of the coating material was reduced. The coating surface was made smoother and denser with a reasonable ratio of polyols to PAPI, preventing the release of non-film-forming substances. When the proportion of soybean oil was 60% and the ratio of polyols to PAPI was 1.2:1, the N release days of the prepared SMPCU reached 137 days. Compared to soybean-oil polyol-coated urea (SOPCU) and polyester polyol-coated urea (PPCU), the nitrogen release days increased by 73.42% (79 days) and 234.15% (41 days), respectively. The ratio of polyols to polyaryl polymethylene isocyanate (PAPI) was explored, as well as the effect of polyol composition on coatings, and prepared SMPCUs with different nitrogen release days. According to the growth needs of crops and soil environmental characteristics, adjusting the proportion of coating materials, prolonging or shortening the nitrogen fertilizer release time, meets the nutritional needs of crops under different planting systems and provides conditions for farmers to plant different crops.