Constanze Eulenkamp
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Constanze Eulenkamp has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Heinz Paul Huber
Munich University of Applied Sciences
3 shared publications - David Redka
Munich University of Applied Sciences
2 shared publications - Maximilian Spellauge
Laser Center HM Munich University of Applied Sciences HM Munich Germany
2 shared publications - Bastian Hartmann
Munich University of Applied Sciences
1 shared publication - Carlos Molpeceres
Centro Laser, Universidad Politécnica de Madrid, C/Alan Turing 1, 28038 Madrid, Spain
1 shared publication - Christian H. Schwalb
Quantum Design Microscopy GmbH 1 , Pfungstadt 64319
1 shared publication
Latest Publications
- Open Access
- 13 July 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of a capping layer on ultrashort pulse laser removal of thin oxide films
Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.
- 13 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of a capping layer on ultrashort pulse laser removal of thin oxide films
Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.
- Open Access
- 4 September 2025
- Published by Wiley in Laser & Photonics Reviews
- Vol. 20 (2)
Single‐Pulse Nanomorphology Governs Laser‐Induced Periodic Surface Structure Formation on Metals
The targeted generation of laser‐induced periodic surface structures (LIPSS) is a powerful technique in modern surface engineering. While the dominant role of optical scattering and surface electromagnetic ways in LIPSS formation is widely acknowledged, formation mechanisms still pose open questions, particularly regarding material‐specific differences in uniformity and prominence. Here, a comparative pulse‐to‐pulse analysis of aluminum and stainless steel is presented, chosen to represent relevant metals that develop rough and smooth crater nanomorphologies, respectively, following single‐pulse irradiation. The findings reveal that the initial nanomorphology governs subsequent LIPSS development. After the initial pulse, aluminum forms pronounced spiky nanostructures characterized by elevated local surface gradients within the ablation crater, leading to strong scattering and localization of surface electromagnetic waves. This suppresses periodic intensity distribution and prevents the formation of LIPSS. In contrast, stainless steel retains a smooth crater morphology after the first pulse, enabling well‐defined systematic progression from high‐frequency to low‐frequency LIPSS. Supported by finite‐difference time‐domain simulations on measured surface topographies, the results quantitatively link initial nanomorphology to optical interactions, fundamentally defining material‐dependent pathways for LIPSS formation. Beyond previous explanations relying on macroscopic material parameters, this nanomorphological perspective provides an additional, yet direct explanation for inherent differences in LIPSS susceptibility among various metals.
- 4 September 2025
- Published by Wiley in Laser & Photonics Reviews
- Vol. 20 (2)
Open AccessSingle‐Pulse Nanomorphology Governs Laser‐Induced Periodic Surface Structure Formation on Metals
The targeted generation of laser‐induced periodic surface structures (LIPSS) is a powerful technique in modern surface engineering. While the dominant role of optical scattering and surface electromagnetic ways in LIPSS formation is widely acknowledged, formation mechanisms still pose open questions, particularly regarding material‐specific differences in uniformity and prominence. Here, a comparative pulse‐to‐pulse analysis of aluminum and stainless steel is presented, chosen to represent relevant metals that develop rough and smooth crater nanomorphologies, respectively, following single‐pulse irradiation. The findings reveal that the initial nanomorphology governs subsequent LIPSS development. After the initial pulse, aluminum forms pronounced spiky nanostructures characterized by elevated local surface gradients within the ablation crater, leading to strong scattering and localization of surface electromagnetic waves. This suppresses periodic intensity distribution and prevents the formation of LIPSS. In contrast, stainless steel retains a smooth crater morphology after the first pulse, enabling well‐defined systematic progression from high‐frequency to low‐frequency LIPSS. Supported by finite‐difference time‐domain simulations on measured surface topographies, the results quantitatively link initial nanomorphology to optical interactions, fundamentally defining material‐dependent pathways for LIPSS formation. Beyond previous explanations relying on macroscopic material parameters, this nanomorphological perspective provides an additional, yet direct explanation for inherent differences in LIPSS susceptibility among various metals.
- 5 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (26) , 43017-43034
Indium tin oxide ultrafast laser lift-off ablation mechanisms and damage minimization
We draw comparisons between the ablation and damage mechanisms that occur for both film and substrate irradiation using atomic force microscopy, scanning electron microscopy, and pump-probe reflectometry. For substrate irradiation, energy absorbed at the film-substrate interface creates a confined energy situation, resulting in a photomechanical lift-off. A partial ablation at the edges of the ablated zone formed the burr and was reduced in height by minimizing the area subject to the partial ablation threshold fluence. Substrate damage is understood to arise from free electron diffusion from indium tin oxide and subsequent laser heating. We establish a process window for substrate irradiation in a single-pulse ablation regime between approximately two to three times the ablation threshold of 0.18 J/cm2, validating the process window seen in literature and provide a crucial understanding for the ablation mechanisms of transparent conductive films.
- 5 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (26) , 43017-43034
Indium tin oxide ultrafast laser lift-off ablation mechanisms and damage minimization
We draw comparisons between the ablation and damage mechanisms that occur for both film and substrate irradiation using atomic force microscopy, scanning electron microscopy, and pump-probe reflectometry. For substrate irradiation, energy absorbed at the film-substrate interface creates a confined energy situation, resulting in a photomechanical lift-off. A partial ablation at the edges of the ablated zone formed the burr and was reduced in height by minimizing the area subject to the partial ablation threshold fluence. Substrate damage is understood to arise from free electron diffusion from indium tin oxide and subsequent laser heating. We establish a process window for substrate irradiation in a single-pulse ablation regime between approximately two to three times the ablation threshold of 0.18 J/cm2, validating the process window seen in literature and provide a crucial understanding for the ablation mechanisms of transparent conductive films.