Liguo Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Liguo Liu has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Yize Sun
College of Mechanical Engineering
3 shared publicationsYujing Zhang
College of Mechanical Engineering
3 shared publications- Zhuo Meng
College of Mechanical Engineering, Donghua University, Shanghai, China
2 shared publications Zhuo Meng
College of Mechanical Engineering
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
Two-relaxation-time lattice Boltzmann model of the velocity profiles and volumetric flow rate of generalized Newtonian fluids in a single-screw extruder
Single-screw extruders and injection molding machines are essential equipment in polymer processing. It is of great importance for the optimization of operating parameters and the design of extrusion screw to predict the throughput of an extruder and the metering time of an injection molding machine according to the geometric parameters of the screw, operating parameters, and the rheological behavior of materials. Most polymer melts exhibit non-Newtonian behavior. The lattice Boltzmann method has many advantages in simulating the flow of non-Newtonian fluids. Herein, the dimensionless velocity profiles and dimensionless volumetric flow rate of generalized Newtonian fluids in a screw channel have been studied using the two-relaxation-time lattice Boltzmann method (TRT–LBM). The numerical results of power-law fluids are in good agreement with the analytical solutions, which verifies the validity of TRT–LBM. Through research, the change rule of the dimensionless volumetric flow rate of Bingham fluids with dimensionless pressure gradient has been obtained. It was found that the rheological properties of polymer melts and the dimensionless pressure gradient significantly affect the dimensionless velocity profiles and dimensionless volumetric flow rate. The dimensionless volume flow rate has some unexpected changes with the increase of the dimensionless pressure gradient. This study can provide theoretical guidance for the optimization of operating parameters and the design of extrusion screws.
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
Open AccessTwo-relaxation-time lattice Boltzmann model of the velocity profiles and volumetric flow rate of generalized Newtonian fluids in a single-screw extruder
Single-screw extruders and injection molding machines are essential equipment in polymer processing. It is of great importance for the optimization of operating parameters and the design of extrusion screw to predict the throughput of an extruder and the metering time of an injection molding machine according to the geometric parameters of the screw, operating parameters, and the rheological behavior of materials. Most polymer melts exhibit non-Newtonian behavior. The lattice Boltzmann method has many advantages in simulating the flow of non-Newtonian fluids. Herein, the dimensionless velocity profiles and dimensionless volumetric flow rate of generalized Newtonian fluids in a screw channel have been studied using the two-relaxation-time lattice Boltzmann method (TRT–LBM). The numerical results of power-law fluids are in good agreement with the analytical solutions, which verifies the validity of TRT–LBM. Through research, the change rule of the dimensionless volumetric flow rate of Bingham fluids with dimensionless pressure gradient has been obtained. It was found that the rheological properties of polymer melts and the dimensionless pressure gradient significantly affect the dimensionless velocity profiles and dimensionless volumetric flow rate. The dimensionless volume flow rate has some unexpected changes with the increase of the dimensionless pressure gradient. This study can provide theoretical guidance for the optimization of operating parameters and the design of extrusion screws.
- Open Access
- 7 December 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (50) , 47991-48018
Simulation of High-Viscosity Generalized Newtonian Fluid Flows in the Mixing Section of a Screw Extruder Using the Lattice Boltzmann Model
The mixing quality of polymer melts in the mixing section of a single-screw extruder and an injection molding machine has considerable effects on the properties of the molded products. Therefore, the study of the flow field of polymer melts in the mixing section is of great importance. The lattice Boltzmann method (LBM) exhibits unique advantages in simulating non-Newtonian fluids. Many researchers have used LBM to study the flow of medium- and low-viscosity fluids. In their studies, the Reynolds number of fluid flows is generally moderate. However, polymer melts are typical high-viscosity fluids, and their flow Reynolds number is generally very small. The single-relaxation-time lattice Boltzmann method (SRT-LBM) has been used previously to study the flow field of power law fluids in the mixing section. Herein, the flow field of high-viscosity generalized Newtonian fluids in the mixing section of a single-screw extruder is studied using SRT-LBM, the two-relaxation-time lattice Boltzmann method (TRT-LBM), and the multiple-relaxation-time lattice Boltzmann method (MRT-LBM). Through comparison, TRT-LBM has been found to exhibit obvious advantages regarding stability, calculation accuracy, calculation efficiency, and selection of simulation parameters. The TRT-LBM is more suitable for studying high-viscosity generalized Newtonian fluids than SRT-LBM and MRT-LBM. SRT-LBM has low computational efficiency when simulating high-viscosity generalized Newtonian fluids, and instability is easily caused when the fluid has a yield stress. For MRT-LBM, only by studying the relaxation parameters can its advantages be fully utilized. However, optimizing the accuracy and stability of the MRT-LBM via parameter research and linear stability analysis is difficult. For non-Newtonian fluids, it is difficult to optimize the relaxation parameters to make the MRT-LBM more stable and accurate than the TRT-LBM. It is difficult for the MRT-LBM to realize its potential when simulating high-viscosity generalized Newtonian fluids. In addition, we studied the flow pattern in the cross section of the screw channel and compared it to the results reported in previous studies.
- 7 December 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (50) , 47991-48018
Open AccessSimulation of High-Viscosity Generalized Newtonian Fluid Flows in the Mixing Section of a Screw Extruder Using the Lattice Boltzmann Model
The mixing quality of polymer melts in the mixing section of a single-screw extruder and an injection molding machine has considerable effects on the properties of the molded products. Therefore, the study of the flow field of polymer melts in the mixing section is of great importance. The lattice Boltzmann method (LBM) exhibits unique advantages in simulating non-Newtonian fluids. Many researchers have used LBM to study the flow of medium- and low-viscosity fluids. In their studies, the Reynolds number of fluid flows is generally moderate. However, polymer melts are typical high-viscosity fluids, and their flow Reynolds number is generally very small. The single-relaxation-time lattice Boltzmann method (SRT-LBM) has been used previously to study the flow field of power law fluids in the mixing section. Herein, the flow field of high-viscosity generalized Newtonian fluids in the mixing section of a single-screw extruder is studied using SRT-LBM, the two-relaxation-time lattice Boltzmann method (TRT-LBM), and the multiple-relaxation-time lattice Boltzmann method (MRT-LBM). Through comparison, TRT-LBM has been found to exhibit obvious advantages regarding stability, calculation accuracy, calculation efficiency, and selection of simulation parameters. The TRT-LBM is more suitable for studying high-viscosity generalized Newtonian fluids than SRT-LBM and MRT-LBM. SRT-LBM has low computational efficiency when simulating high-viscosity generalized Newtonian fluids, and instability is easily caused when the fluid has a yield stress. For MRT-LBM, only by studying the relaxation parameters can its advantages be fully utilized. However, optimizing the accuracy and stability of the MRT-LBM via parameter research and linear stability analysis is difficult. For non-Newtonian fluids, it is difficult to optimize the relaxation parameters to make the MRT-LBM more stable and accurate than the TRT-LBM. It is difficult for the MRT-LBM to realize its potential when simulating high-viscosity generalized Newtonian fluids. In addition, we studied the flow pattern in the cross section of the screw channel and compared it to the results reported in previous studies.