Kirk Jahnel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kirk Jahnel has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Dennis Patrick Wilhelm
1 shared publication- Dennis Patrick Wilhelm
Department of Fine Machining and Optics, Fraunhofer Institute for Production Technology IPT, 52074 Aachen, Germany
1 shared publication - Robert Michels
Department of Fine Machining and Optics, Fraunhofer Institute for Production Technology IPT, 52074 Aachen, Germany
1 shared publication Sebastian Hähnel
1 shared publicationThomas Bergs
1 shared publication- Thomas Bergs
Manufacturing Technology Institute—MTI of RWTH Aachen University, Campus-Boulevard 30, 52074 Aachen, Germany
1 shared publication
Latest Publications
- Open Access
- 14 December 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (12) , 2240
Investigation of Surface Integrity Induced by Ultra-Precision Grinding and Scratching of Glassy Carbon
Glassy carbon provides material characteristics that make it a promising candidate for use as a mould material in precision glass moulding. However, to effectively utilize glassy carbon, a thorough investigation into the machining of high-precision optical surfaces is necessary, which has not been thoroughly investigated. This research analyses the process of material removal and its resulting surface integrity through the use of nano-scratching and ultra-precision grinding. The nano-scratching process begins with ductile plastic deformation, then progresses with funnel-shaped breakouts in the contact zone, and finally concludes with brittle conchoidal breakouts when the cutting depth is increased. The influence of process factors and tool-related parameters resulting from grinding has discernible impacts on the ultimate surface roughness and topography. Enhancing the cutting speed during cross-axis kinematic grinding results in improved surface roughness. Increasing the size of diamond grains and feed rates leads to an increase in surface roughness. An achievable surface roughness of Ra < 5 nm together with ductile-regime grinding behaviour meet optical standards, which makes ultra-precision grinding a suitable process for optical surface generation.
- 14 December 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (12) , 2240
Open AccessInvestigation of Surface Integrity Induced by Ultra-Precision Grinding and Scratching of Glassy Carbon
Glassy carbon provides material characteristics that make it a promising candidate for use as a mould material in precision glass moulding. However, to effectively utilize glassy carbon, a thorough investigation into the machining of high-precision optical surfaces is necessary, which has not been thoroughly investigated. This research analyses the process of material removal and its resulting surface integrity through the use of nano-scratching and ultra-precision grinding. The nano-scratching process begins with ductile plastic deformation, then progresses with funnel-shaped breakouts in the contact zone, and finally concludes with brittle conchoidal breakouts when the cutting depth is increased. The influence of process factors and tool-related parameters resulting from grinding has discernible impacts on the ultimate surface roughness and topography. Enhancing the cutting speed during cross-axis kinematic grinding results in improved surface roughness. Increasing the size of diamond grains and feed rates leads to an increase in surface roughness. An achievable surface roughness of Ra < 5 nm together with ductile-regime grinding behaviour meet optical standards, which makes ultra-precision grinding a suitable process for optical surface generation.
- Open Access
- 1 January 2023
- Published by VDI Fachmedien GmbH and Co. KG in wt Werkstattstechnik online
- Vol. 113 (06) , 249-254
Prozessoptimierung beim Glaswafer-Trennschleifen/Process optimization in glass wafer cut-off grinding - Cut-off grinding with direct substrate fixation on cutting foils to save costs and time
Fast-Axis-Kollimatoren (FAC) sind essenzielle optische Elemente für Diodenlasersysteme. Beim aktuellen Prozess des Trennschleifens mit nachgelagerter Reinigung von FAC-Optiken aus gepressten antireflexionsbeschichteten Glaswafern entstehen vermehrt Beschädigungen, die eine Verwendung der Optiken limitiert. Die Verwendung von Schneidfolie zur Substratfixierung beim Trennschleifen der FAC-Optiken ermöglicht ein defektfreies Schneiden und Lösen ohne Reinigung von der Folie und gleichzeitig können Kosten und Fertigungszeit eingespart werden. Fast Axis Collimators (FAC) are essential optical elements for diode laser systems. The increasing number of damages occuring in the current process of cut-off grinding with downstream cleaning of FAC optics made of pressed anti-reflective coated glass wafers limits the use of optics in high-power applications. Using cutting film for substrate fixation during cut-off grinding of FAC optics allows for defect-free cutting and clean release from the cutting film while saving costs and production time.
- 1 January 2023
- Published by VDI Fachmedien GmbH and Co. KG in wt Werkstattstechnik online
- Vol. 113 (06) , 249-254
Open AccessProzessoptimierung beim Glaswafer-Trennschleifen/Process optimization in glass wafer cut-off grinding - Cut-off grinding with direct substrate fixation on cutting foils to save costs and time
Fast-Axis-Kollimatoren (FAC) sind essenzielle optische Elemente für Diodenlasersysteme. Beim aktuellen Prozess des Trennschleifens mit nachgelagerter Reinigung von FAC-Optiken aus gepressten antireflexionsbeschichteten Glaswafern entstehen vermehrt Beschädigungen, die eine Verwendung der Optiken limitiert. Die Verwendung von Schneidfolie zur Substratfixierung beim Trennschleifen der FAC-Optiken ermöglicht ein defektfreies Schneiden und Lösen ohne Reinigung von der Folie und gleichzeitig können Kosten und Fertigungszeit eingespart werden. Fast Axis Collimators (FAC) are essential optical elements for diode laser systems. The increasing number of damages occuring in the current process of cut-off grinding with downstream cleaning of FAC optics made of pressed anti-reflective coated glass wafers limits the use of optics in high-power applications. Using cutting film for substrate fixation during cut-off grinding of FAC optics allows for defect-free cutting and clean release from the cutting film while saving costs and production time.