BSBharani Kumar Sekar

Bharani Kumar Sekar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bharani Kumar Sekar has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Microstructural and mechanical characterization of AA2124 aluminum alloy matrix composites reinforced with Si3 N4 particulates fabricated by powder metallurgy and high-energy ball milling

    by Bharani Kumar Sekar, Grandhi Venkata Krishna Pradeep, Ragunathan Silambarasan, Ratchagaraja Dhairiyasamy

    The study aims to enhance the mechanical properties of AA2124 aluminum alloy matrix composites reinforced with silicon nitride (Si3N4) particulates, utilizing powder metallurgy and high-energy ball milling techniques. Reinforcing metal matrices with ceramic particulates like Si3N4 offers potential strength, hardness, and thermal stability improvements for advanced engineering applications. AA2124 alloy powder was mixed with Si3N4 particulates (5-20 wt%) and milled for varying durations to achieve uniform dispersion. The mixtures were compacted and sintered at 500°C in an argon atmosphere. Microstructural characterization was performed using SEM, XRD, and particle size analysis. Mechanical properties were evaluated through tensile, fatigue, and creep tests, along with microhardness measurements. The composites exhibited significant improvements in mechanical properties, with optimal results observed at 15 wt% Si3N4 and 60 minutes of milling. The tensile strength increased to 475 MPa from 320 MPa, and microhardness reached 297 kgf/mm2 compared to 37 kgf/mm2 for the unreinforced alloy. Enhanced fatigue life and creep resistance were also noted. This study demonstrates that optimizing Si3N4 content and milling duration can significantly enhance the mechanical properties of AA2124 composites, making them suitable for aerospace and other high-performance applications. The findings provide a basis for developing advanced aluminum matrix composites with superior mechanical properties.


  • Open Access

    Mathematical modeling of thin layer drying characteristics of Okra (Abelmoschus Esculentus)

    by S. D. Sekar, P. Duraimurugan, N. Mohanrajhu, S. Bharani Kumar, S. Rajesh

    The passive and active drying capabilities of okra (Abelmoschus Esculentus) were examined in the current study using heat pump drying, open sun drying, and greenhouse drying with two distinct glazing materials (Drip Lock sheet and UV Polyethylene sheet). The fastest drying method is heat pump drying, which has a drying rate of 4.63 g/h. While UV polyethylene sheet active mode and drip lock sheet passive mode have drying rates of 4.07 g/h, drip lock greenhouse active mode had a drying rate of 4.12 g/h. Open sun drying had a lower drying rate of 2.68 g/h compared to other drying modes. According to the statistical analysis, the Prakash and Kumar model is the most effective model for drying okra among all drying methods from the chosen twelve mathematical models.

  • Open Access

    Performance analysis of thin layer drying of okra (abelmoschus esculentus)

    by S. D. Sekar, S. Rajesh, P. J. Lokesh Kumar, S. Bharani Kumar, M. Vinosh

    Studies on the thin layer drying kinetics of okra (Abelmoschus esculentus) in passive and active methods with open, heat pump dry, and greenhouse dry using various film materials, including UV Polyethylene sheet and drip lock film, have been conducted. Food products are dried to lower their moisture content, increase shelf life, and decrease post-harvest waste. In total, it took 16 hours for the okra to dry under open sun drying (OSD), 14 hours in an UV poly-ethylene sheet greenhouse dryer operating in passive method (UVPM), 13 hours in a drip lock sheet greenhouse dryer operating in passive method (DLPM), and 12 hours in an UV polyethylene sheet greenhouse dryer operating in active mode. HPD achieved the highest dryer efficiency of 38.78% whereas Drip Lock Sheet Active Mode (DLAM) greenhouse drying had the lowest efficiency of 14.15%. When drying okra, HPD produced a lower effective moisture diffusivity of 1.04 x 10−10 m2/s compared to other modes, which produced a higher effective moisture diffusivity of 2.09 x 10−10 m2/s. The Heat Pump dryer (HPD) exhibited a higher Specific Moisture Extraction Rate (SMER) of 2.60 kg/kWh when compared to conventional drying methods. It was discovered that HPD dried materials more quickly than greenhouse drying, yet greenhouse drying is more economical from an economic standpoint.