RQRegina Qelibari

Regina Qelibari

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Regina Qelibari has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • PEEK-Reinforced Sulfonated Poly(phenylene sulfone)-Membrane for Water Electrolysis with Lower Gas Crossover and Lower Resistance Than N115

    by Regina Qelibari, Andreas Münchinger, Giorgi Titvinidze, Carolin Klose, Severin Vierrath

    Fluorine-free hydrocarbon polymers have the potential to be more environmentally friendly and cost-effective than current perfluorinated sulfonic acids (PFSA). These hydrocarbon polymers have a unique morphology that reduces gas transfer while maintaining high proton conductivity, making them a promising alternative to PFSA membranes in water electrolysis.[1] In an initial study, we demonstrate the potential of hydrocarbon membranes in electrolyzers using sulfonated polyphenylene sulfone (sPPS).[2] However, to achieve good performance, a high ion exchange capacity (2.17 - 3.57 meq/g) is required. This results in a high water uptake, which leads to membrane softening and detachment of the electrodes. In addition, excessive swelling makes upscaling, i.e., coating of the electrodes directly onto the membrane, impossible. To solve this problem, we have integrated a woven, open-mesh PEEK substrate (Fig.1, right).[3] The reinforced membrane shows a significant enhancement in the mechanical robustness and dimensional stability of the membrane, which leads to a strong reduction of water uptake from 294% to 115%. This allows direct casting of electrodes onto the membrane, an essential step for scaled production. Moreover, the reinforced membrane demonstrates a significantly lower electrical resistance of 70 mΩ cm² (versus 159 mΩ cm² for Nafion), attributed to its reduced thickness (74 µm compared to 127 µm) and higher ion exchange capacity. At the same time, the crossover is also strongly reduced as displayed in Figure 1. This leads to a better figure of merit, given by the ratio of conductivity to permeability, as shown in Figure 1 (right bottom), where crossover current densities are plotted over the high frequency resistance.[3] Figure 1Illustration of the casting Process of the reinforced membrane and fabrication of a one side coated CCM (left). IV-curve of the PEEK-sPPS membrane and a Nafion 115 reference (top right) and the figure of merit for PEEK-sPPS and two reference membranes (N115 and N212). Literature: [1] Miyake, J.; Taki, R.; Mochizuki, T.; Shimizu, R.; Akiyama, R.; Uchida, M.; Miyatake, K. Design of flexible polyphenylene proton-conducting membrane for next-generation fuel cells. Sci. Adv. 2017, 3(10), eaao0476. DOI: 10.1126/sciadv.aao0476 [2] Klose, C.; Saatkamp, T.; Münchinger, A.; Bohn, L.; Titvinidze, G.; Breitwieser, M.; Kreuer, K.; Vierrath, S. All‐Hydrocarbon MEA for PEM Water Electrolysis Combining Low Hydrogen Crossover and High Efficiency. Adv. Energy Mater. 2020, 10 (14), 1903995. DOI: 10.1002/aenm.201903995 [3] Qelibari, R.; Cruz Ortiz, E.; van Treel, N.; Lombeck, F.; Schare, C.; Münchinger, A.; Dumbadze. N.; Titvinidze, G.; Klose, C.; Vierrath, S. 74 µm PEEK-reinforced sulfonated poly(phenylene sulfone)-membrane for stable water electrolysis with lower gas crossover and lower resistance than Nafion N115. Adv. Energy Mater. 2023, 14 (5), 2303271. DOI: 10.1002/aenm.202303271 Figure 1

  • Open Access

    74 µm PEEK‐Reinforced Sulfonated Poly(phenylene sulfone)‐Membrane for Stable Water Electrolysis with Lower Gas Crossover and Lower Resistance than Nafion N115

    by Regina Qelibari, Edgar Cruz Ortiz, Niklas van Treel, Florian Lombeck, Clara Schare, Andreas Münchinger, Nodar Dumbadze, Giorgi Titvinidze, Carolin Klose, Severin Vierrath

    Polymer electrolyte membrane (PEM) water electrolysis is a crucial technology for green hydrogen production. Hydrocarbon membranes are drawing a lot of attention due to potentially superior properties and the fact that common fluorinated polymers might face a potential ban. This study introduces a sulfonated poly(phenylene sulfone) (sPPS) membrane, reinforced with a poly(ether‐ether‐ketone) (PEEK) mesh. The reinforced membrane induces a drastic increase in dimensional stability, enabling direct anode casting—an essential step toward industrial manufacturing. It further exhibits a significant reduction in water uptake (115% vs 294% for pure sPPS) and a 40% lower H2‐crossover (0.18 mA cm−2) compared to the industry standard N115 (0.31 mA cm−2). Due to the lower thickness (74 vs 127 µm) and higher ion exchange capacity (IEC)(1.92 vs 0.89 mmol g−1), the PEEK‐sPPS membrane displays a substantially lower resistance (70 vs 159 mΩ cm2 for N115). This directly translates into a voltage reduction of ≈90 mV at 1 A cm−2 or ≈180 mV at 2 A cm−2, both typical operating current densities. Finally, PEEK‐sPPS exhibits the longest lifetime shown for hydrocarbon membranes with almost 650 h at 1 A cm−2 and a low degradation rate (80 µV h−1).