Tadele T. Filate
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tadele T. Filate has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Ergang Wang
Department of Chemistry and Chemical Engineering Chalmers University of Technology Göteborg Sweden
4 shared publications - Wendimagegn Mammo
Department of Chemistry Addis Ababa University Addis Ababa Ethiopia
4 shared publications Zewdneh Genene
Department of Chemistry and Chemical Engineering
3 shared publications- Ludvig Edman
Umeå University
2 shared publications Qiaonan Chen
Department of Chemistry and Chemical Engineering
2 shared publications- Christian Larsen
The Organic Photonics and Electronics Group, Department of Physics, Umeå University, SE-90187 Umeå, Sweden
1 shared publication
Latest Publications
- Open Access
Green‐Solvent‐Processed Inverted Layer‐by‐Layer Organic Solar Cells Enabled by an Aqueous Soluble Thiophene‐ alt ‐Quinoxaline Donor Polymer
Efficient organic solar cells (OSCs) traditionally rely on bulk heterojunction structures due to the limited exciton diffusion lengths (L D ). The evolution of materials with extended L D , such as the appearance of nonfullerene acceptors (NFAs), enables sequential layer‐by‐layer (LbL) processing of electron donor (D) and acceptor (A) a promising strategy for better control over the morphologies of active layers with configuration of D/A in OSCs. However, its application in an inverted structure, that is A/D, remains underexplored, primarily due to the inadequate solvent resistance of small‐molecule NFAs, which are prone to dissolved during the solution deposition of the D layer. In this work, we report a fully orthogonal, green‐solvent‐based LbL strategy for fabricating inverted OSCs using small‐molecule NFAs. By pairing a water/ethanol‐soluble thiophene‐ alt ‐quinoxaline‐based donor polymer, P(Qx8O‐T), with an o ‐xylene‐processed acceptor, L8‐BO, we successfully suppressed interlayer dissolution, allowing intact deposition of the donor layer without damaging the underlying acceptor film. Furthermore, this strategy effectively maintains the intrinsic crystallization of the donor and NFA layers, resulting in high‐quality active layers with well‐defined vertical phase separation. Consequently, the green‐solvent‐processed inverted LbL devices achieve a power conversion efficiency of 5.88%, demonstrating the feasibility of OSCs as a green PV technology.
Open AccessGreen‐Solvent‐Processed Inverted Layer‐by‐Layer Organic Solar Cells Enabled by an Aqueous Soluble Thiophene‐ alt ‐Quinoxaline Donor Polymer
Efficient organic solar cells (OSCs) traditionally rely on bulk heterojunction structures due to the limited exciton diffusion lengths (L D ). The evolution of materials with extended L D , such as the appearance of nonfullerene acceptors (NFAs), enables sequential layer‐by‐layer (LbL) processing of electron donor (D) and acceptor (A) a promising strategy for better control over the morphologies of active layers with configuration of D/A in OSCs. However, its application in an inverted structure, that is A/D, remains underexplored, primarily due to the inadequate solvent resistance of small‐molecule NFAs, which are prone to dissolved during the solution deposition of the D layer. In this work, we report a fully orthogonal, green‐solvent‐based LbL strategy for fabricating inverted OSCs using small‐molecule NFAs. By pairing a water/ethanol‐soluble thiophene‐ alt ‐quinoxaline‐based donor polymer, P(Qx8O‐T), with an o ‐xylene‐processed acceptor, L8‐BO, we successfully suppressed interlayer dissolution, allowing intact deposition of the donor layer without damaging the underlying acceptor film. Furthermore, this strategy effectively maintains the intrinsic crystallization of the donor and NFA layers, resulting in high‐quality active layers with well‐defined vertical phase separation. Consequently, the green‐solvent‐processed inverted LbL devices achieve a power conversion efficiency of 5.88%, demonstrating the feasibility of OSCs as a green PV technology.
- Open Access
- 19 October 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (20) , 8120-8130
Thiadiazolobenzotriazole-Based Donor–Acceptor Terpolymers That Can Be Processed from Green Solvents and Deliver 950 nm Emission in Light-Emitting Electrochemical Cells
Organic semiconductors that deliver emission with a wavelength exceeding 900 nm can enable a wide range of applications, but the unfortunate fact is that only a small number of such emitters have been synthesized and have demonstrated emissive function in devices. Here, this issue is addressed through the design and synthesis of two terpolymers that comprise a low energy-gap thiophene-thiadiazolobenzotriazole (TBTzTD) donor-acceptor unit as the minority guest incorporated in a majority donor-acceptor conjugated copolymer host, being either thiophene-quinoxaline (TQ) or thiophene-difluoroquinoxaline (TQ2F). These terpolymers are further endowed with high solubility in benign hydrophilic solvents through the grafting of branched oligo-(ethylene glycol) side chains onto the quinoxaline unit. The application function of the terpolymer emitters is demonstrated through their implementation in light-emitting electrochemical cells (LECs). It is notable from a sustainability perspective that the emitter is metal free and that the single-layer LEC active material is cast from an environmentally benign water:ethanol solvent blend. From an application perspective, it is attractive that the terpolymer-LEC devices feature a very fast turn-on to significant radiance at low voltage and that they deliver emission with a peak wavelength of 935 nm with TQ-TBTzTD as the emitter and 950 nm with TQ2F-TBTzTD as the emitter.
- 19 October 2025
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 37 (20) , 8120-8130
Open AccessThiadiazolobenzotriazole-Based Donor–Acceptor Terpolymers That Can Be Processed from Green Solvents and Deliver 950 nm Emission in Light-Emitting Electrochemical Cells
Organic semiconductors that deliver emission with a wavelength exceeding 900 nm can enable a wide range of applications, but the unfortunate fact is that only a small number of such emitters have been synthesized and have demonstrated emissive function in devices. Here, this issue is addressed through the design and synthesis of two terpolymers that comprise a low energy-gap thiophene-thiadiazolobenzotriazole (TBTzTD) donor-acceptor unit as the minority guest incorporated in a majority donor-acceptor conjugated copolymer host, being either thiophene-quinoxaline (TQ) or thiophene-difluoroquinoxaline (TQ2F). These terpolymers are further endowed with high solubility in benign hydrophilic solvents through the grafting of branched oligo-(ethylene glycol) side chains onto the quinoxaline unit. The application function of the terpolymer emitters is demonstrated through their implementation in light-emitting electrochemical cells (LECs). It is notable from a sustainability perspective that the emitter is metal free and that the single-layer LEC active material is cast from an environmentally benign water:ethanol solvent blend. From an application perspective, it is attractive that the terpolymer-LEC devices feature a very fast turn-on to significant radiance at low voltage and that they deliver emission with a peak wavelength of 935 nm with TQ-TBTzTD as the emitter and 950 nm with TQ2F-TBTzTD as the emitter.
- Open Access
- 1 March 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (10) , 12886-12896
Aqueous Processed All-Polymer Solar Cells with High Open-Circuit Voltage Based on Low-Cost Thiophene–Quinoxaline Polymers
Eco-friendly solution processing and the low-cost synthesis of photoactive materials are important requirements for the commercialization of organic solar cells (OSCs). Although varieties of aqueous-soluble acceptors have been developed, the availability of aqueous-processable polymer donors remains quite limited. In particular, the generally shallow highest occupied molecular orbital (HOMO) energy levels of existing polymer donors limit further increases in the power conversion efficiency (PCE). Here, we design and synthesize two water/alcohol-processable polymer donors, poly[(thiophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-T) ) and poly[(selenophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-Se)) with oligo(ethylene glycol) (OEG) side chains, having deep HOMO energy levels (∼-5.4 eV). The synthesis of the polymers is achieved in a few synthetic and purification steps at reduced cost. The theoretical calculations uncover that the dielectric environmental variations are responsible for the observed band gap lowering in OEG-based polymers compared to their alkylated counterparts. Notably, the aqueous-processed all-polymer solar cells (aq-APSCs) based on P(Qx8O-T) and poly[(N,N'-bis(3-(2-(2-(2-methoxyethoxy)-ethoxy)ethoxy)-2-((2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-methyl)propyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl)-alt-(2,5-thiophene)] (P(NDIDEG-T)) active layer exhibit a PCE of 2.27% and high open-circuit voltage (VOC) approaching 0.8 V, which are among the highest values for aq-APSCs reported to date. This study provides important clues for the design of low-cost, aqueous-processable polymer donors and the fabrication of aqueous-processable OSCs with high VOC.
- 1 March 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (10) , 12886-12896
Open AccessAqueous Processed All-Polymer Solar Cells with High Open-Circuit Voltage Based on Low-Cost Thiophene–Quinoxaline Polymers
Eco-friendly solution processing and the low-cost synthesis of photoactive materials are important requirements for the commercialization of organic solar cells (OSCs). Although varieties of aqueous-soluble acceptors have been developed, the availability of aqueous-processable polymer donors remains quite limited. In particular, the generally shallow highest occupied molecular orbital (HOMO) energy levels of existing polymer donors limit further increases in the power conversion efficiency (PCE). Here, we design and synthesize two water/alcohol-processable polymer donors, poly[(thiophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-T) ) and poly[(selenophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-Se)) with oligo(ethylene glycol) (OEG) side chains, having deep HOMO energy levels (∼-5.4 eV). The synthesis of the polymers is achieved in a few synthetic and purification steps at reduced cost. The theoretical calculations uncover that the dielectric environmental variations are responsible for the observed band gap lowering in OEG-based polymers compared to their alkylated counterparts. Notably, the aqueous-processed all-polymer solar cells (aq-APSCs) based on P(Qx8O-T) and poly[(N,N'-bis(3-(2-(2-(2-methoxyethoxy)-ethoxy)ethoxy)-2-((2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-methyl)propyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl)-alt-(2,5-thiophene)] (P(NDIDEG-T)) active layer exhibit a PCE of 2.27% and high open-circuit voltage (VOC) approaching 0.8 V, which are among the highest values for aq-APSCs reported to date. This study provides important clues for the design of low-cost, aqueous-processable polymer donors and the fabrication of aqueous-processable OSCs with high VOC.
- Open Access
- 8 December 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (3)
Hydrophilic Conjugated Polymers for Sustainable Fabrication of Deep‐Red Light‐Emitting Electrochemical Cells
It is crucial to develop functional electronic materials that can be processed from green solvents to achieve environmentally sustainable and cost‐efficient printing fabrication of organic electronic devices. Here, the design and cost‐efficient synthesis of two hydrophilic and emissive conjugated polymers, TQ‐OEG and TQ2F‐OEG, are presented, which are rendered hydrophilic through the grafting of oligo(ethylene glycol) (OEG) solubilizing groups onto the thiophene‐quinoxaline conjugated backbone and thereby can be processed from a water:ethanol solvent mixture. The results show that the introduction of the OEG groups enables for a direct dissolution of salts by the neat polymer for the attainment of solid‐state ion mobility. These properties are utilized for the design and development of light‐emitting electrochemical cells (LECs), the active materials of which can be solution cast from a water:ethanol‐based ink. It is specifically shown that such an LEC device, comprising an optimized blend of the TQ2F‐OEG emitter and a Li salt as the active material positioned between two air‐stabile electrodes, delivers deep‐red emission (peak wavelength = 670 nm) with a radiance of 185 µW m−2 at a low drive voltage of 2.3 V. This study contributes relevant information as to how polymers and LEC devices can be designed and fabricated to combine functionality with sustainability.
- 8 December 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (3)
Open AccessHydrophilic Conjugated Polymers for Sustainable Fabrication of Deep‐Red Light‐Emitting Electrochemical Cells
It is crucial to develop functional electronic materials that can be processed from green solvents to achieve environmentally sustainable and cost‐efficient printing fabrication of organic electronic devices. Here, the design and cost‐efficient synthesis of two hydrophilic and emissive conjugated polymers, TQ‐OEG and TQ2F‐OEG, are presented, which are rendered hydrophilic through the grafting of oligo(ethylene glycol) (OEG) solubilizing groups onto the thiophene‐quinoxaline conjugated backbone and thereby can be processed from a water:ethanol solvent mixture. The results show that the introduction of the OEG groups enables for a direct dissolution of salts by the neat polymer for the attainment of solid‐state ion mobility. These properties are utilized for the design and development of light‐emitting electrochemical cells (LECs), the active materials of which can be solution cast from a water:ethanol‐based ink. It is specifically shown that such an LEC device, comprising an optimized blend of the TQ2F‐OEG emitter and a Li salt as the active material positioned between two air‐stabile electrodes, delivers deep‐red emission (peak wavelength = 670 nm) with a radiance of 185 µW m−2 at a low drive voltage of 2.3 V. This study contributes relevant information as to how polymers and LEC devices can be designed and fabricated to combine functionality with sustainability.