Bibhu Kalyan Panda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bibhu Kalyan Panda has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ashish Kumar Nath
Department of Mechanical Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
2 shared publications - Cheruvu Siva Kumar
Department of Mechanical Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
2 shared publications - Seshadev Sahoo
Siksha ‘O’ Anusandhan, Bhubaneswar, India
2 shared publications
Latest Publications
- 24 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (9)
Investigating the Microstructural and Mechanical Characteristics of Laser Additive‐Manufactured AlSi10Mg Specimens Through Experimental and Phase‐Field Modeling Approaches
Metal‐based additive manufacturing can make complicated parts that are complex or expensive to cast and process. Rapid cooling rates increase laser powder bed fusion (LPBF's) mechanical properties during manufacturing. The objective of this study is to examine the impact of process parameters in the L‐PBF technique on the characteristics of microstructure and mechanical properties, specifically, on the nanohardness influenced by Si segregation. The microstructures of the produced specimens are examined using field‐emission scanning electron microscopy and the analysis identifies the existence of bimodal equiaxed α‐Al grains, accompanied by Si phases located within their grain boundaries. In addition, the solidified sample exhibits the segregation of secondary precipitates, particularly Mg2Si, which results in enhanced mechanical properties. Both cellular walls and Si precipitates impede the motion and generation of dislocations, thereby influencing the overall behavior of dislocations. The examination of segregation at the top layer is conducted in a comprehensive manner, subsequently using energy‐dispersive X‐ray spectroscopy for analysis. The presence of Mg2Si, Al2MgSi2, and other phases in all samples is confirmed through X‐ray diffraction. The as‐built samples’ residual stress under different process conditions is also investigated. Additionally, the obtained microstructure is compared to a phase‐field model to forecast the evolution of the microstructure.
- 24 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (9)
Investigating the Microstructural and Mechanical Characteristics of Laser Additive‐Manufactured AlSi10Mg Specimens Through Experimental and Phase‐Field Modeling Approaches
Metal‐based additive manufacturing can make complicated parts that are complex or expensive to cast and process. Rapid cooling rates increase laser powder bed fusion (LPBF's) mechanical properties during manufacturing. The objective of this study is to examine the impact of process parameters in the L‐PBF technique on the characteristics of microstructure and mechanical properties, specifically, on the nanohardness influenced by Si segregation. The microstructures of the produced specimens are examined using field‐emission scanning electron microscopy and the analysis identifies the existence of bimodal equiaxed α‐Al grains, accompanied by Si phases located within their grain boundaries. In addition, the solidified sample exhibits the segregation of secondary precipitates, particularly Mg2Si, which results in enhanced mechanical properties. Both cellular walls and Si precipitates impede the motion and generation of dislocations, thereby influencing the overall behavior of dislocations. The examination of segregation at the top layer is conducted in a comprehensive manner, subsequently using energy‐dispersive X‐ray spectroscopy for analysis. The presence of Mg2Si, Al2MgSi2, and other phases in all samples is confirmed through X‐ray diffraction. The as‐built samples’ residual stress under different process conditions is also investigated. Additionally, the obtained microstructure is compared to a phase‐field model to forecast the evolution of the microstructure.
- Open Access
- 15 December 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 36 (1)
Investigating the influence of thermal behavior on microstructure during solidification in laser powder bed fusion of AlSi10Mg alloys: A phase-field analysis
The utilization of the laser powder bed fusion (L-PBF) method in additive manufacturing experiments has revealed the intriguing potential to induce morphological evolutions within the solidification microstructure by manipulating the thermal conditions. Transitions of this nature can have a substantial impact on the ultimate texture and material properties of the product. This study utilizes numerical investigations to examine the microstructure evolution of the AlSi10Mg alloy, which is fabricated using the L-PBF process, under different thermal conditions. In order to investigate the changes in the microstructure, we employ a parameter phase-field (PF) model. This model effectively replicates the natural development of nuclei from inoculant particles and accurately simulates the transitions in the morphology. The PF model’s validity is determined through the numerical investigation of morphological transitions during directional solidification of the AlSi10Mg alloy. The model’s predictions are then compared to the analytical Hunt model. The formation of a columnar microstructure with a significantly reduced secondary dendrite arm spacing is observed when the ratio of the temperature gradient (G) to the solidification rate (R) is increased.
- 15 December 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 36 (1)
Open AccessInvestigating the influence of thermal behavior on microstructure during solidification in laser powder bed fusion of AlSi10Mg alloys: A phase-field analysis
The utilization of the laser powder bed fusion (L-PBF) method in additive manufacturing experiments has revealed the intriguing potential to induce morphological evolutions within the solidification microstructure by manipulating the thermal conditions. Transitions of this nature can have a substantial impact on the ultimate texture and material properties of the product. This study utilizes numerical investigations to examine the microstructure evolution of the AlSi10Mg alloy, which is fabricated using the L-PBF process, under different thermal conditions. In order to investigate the changes in the microstructure, we employ a parameter phase-field (PF) model. This model effectively replicates the natural development of nuclei from inoculant particles and accurately simulates the transitions in the morphology. The PF model’s validity is determined through the numerical investigation of morphological transitions during directional solidification of the AlSi10Mg alloy. The model’s predictions are then compared to the analytical Hunt model. The formation of a columnar microstructure with a significantly reduced secondary dendrite arm spacing is observed when the ratio of the temperature gradient (G) to the solidification rate (R) is increased.