Eka Mulya Alamsyah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eka Mulya Alamsyah has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Sutrisno Sutrisno
School of Life Sciences and Technology Institut Teknologi Bandung Jl
2 shared publications- Yoyo Suhaya
Bandung Institute of Technology
2 shared publications - Arif Nuryawan
Faculty of Forestry, Universitas Sumatera Utara
1 shared publication - Atmawi Darwis
Forestry Technology Research Group, School of Life Sciences and Technology, Bandung Institute of Technology, Bandung, Indonesia
1 shared publication - Halimatuddahliana Nasution
Universitas Sumatera Utara
1 shared publication - Ihak Sumardi
School of Life Sciences and Technology, Institut Teknologi Bandung, Bandung 40132, Indonesia
1 shared publication
Latest Publications
- 16 December 2023
- Published by Springer Nature
- p. 51-71
Particleboard Made of Eucalyptus Wood Bonded by Isocyanate Resin: Considering Moisture Content of the Particles
- 16 December 2023
- Published by Springer Nature
- p. 51-71
Particleboard Made of Eucalyptus Wood Bonded by Isocyanate Resin: Considering Moisture Content of the Particles
- Open Access
- 25 July 2023
- Published by BioResources in BioResources
- Vol. 18 (3) , 6132-6141
Modified grain orientation of laminated veneer lumber characteristics of three fast-growing tropical wood species
Laminated veneer lumber (LVL) and modified grain orientation of LVL (LVB) are composite products made from veneer that are predicted to replace construction timber. The purpose of this study was to determine the physical and mechanical properties of LVL and LVB of mahoni (Swietenia macrophylla), manglid (Manglietia glauca), and gmelina (Gmelina moluccana) and to compare their characteristics. The results showed that the physical and mechanical properties of LVL and LVB generally meet the standards for use in construction. Differences in the properties of LVL and LVB occurred in the properties of hardness and screw tests, while the other properties were similar. The parallel fiber direction was better in terms of adhesive strength, while the compaction density was slightly higher than LVL. The LVL flexural strength was better than LVB in flat and edge test directions. This difference correlates with the adhesive strength in the shear strength test due to the different orientation of the fiber directions.
- 25 July 2023
- Published by BioResources in BioResources
- Vol. 18 (3) , 6132-6141
Open AccessModified grain orientation of laminated veneer lumber characteristics of three fast-growing tropical wood species
Laminated veneer lumber (LVL) and modified grain orientation of LVL (LVB) are composite products made from veneer that are predicted to replace construction timber. The purpose of this study was to determine the physical and mechanical properties of LVL and LVB of mahoni (Swietenia macrophylla), manglid (Manglietia glauca), and gmelina (Gmelina moluccana) and to compare their characteristics. The results showed that the physical and mechanical properties of LVL and LVB generally meet the standards for use in construction. Differences in the properties of LVL and LVB occurred in the properties of hardness and screw tests, while the other properties were similar. The parallel fiber direction was better in terms of adhesive strength, while the compaction density was slightly higher than LVL. The LVL flexural strength was better than LVB in flat and edge test directions. This difference correlates with the adhesive strength in the shear strength test due to the different orientation of the fiber directions.
- Open Access
- 1 January 2021
- Published by Walter de Gruyter GmbH in Open Agriculture
- Vol. 6 (1) , 392-399
Investigation of the adhesion performance of some fast-growing wood species based on their wettability
The objective of this study was to investigate the adhesion performance of eight fast-growing wood species, namely, Enterolobium cyclocarpum, Paraserianthes falcataria, Shorea sp., Toona sinensis, Gmelina arborea, Pinus merkusii, Acacia mangium, and Acacia hybrid obtained from the tropical region. The wettability test was conducted by contact angle measurement, while the adhesion performance was expressed by strength retention (SR) and wood failure (WF) percentages through block shear tested under the Japanese Agricultural Standard (JAS). Results showed that smaller contact angle for P. falcataria followed by E. cyclocarpum, P. merkusii, T. sinensis, and Shorea indicated that the surfaces were easier to be glued than that of G. arborea, A. mangium, and A. hybrid. It is indicated that high wettability of P. falcataria, E. cyclocarpum, P. merkusii, T. sinensis, and Shorea resulted in the better adhesive spread and more intimate contact between the wood surface and the adhesive as shown by their high SR with high WF percentages.
- 1 January 2021
- Published by Walter de Gruyter GmbH in Open Agriculture
- Vol. 6 (1) , 392-399
Open AccessInvestigation of the adhesion performance of some fast-growing wood species based on their wettability
The objective of this study was to investigate the adhesion performance of eight fast-growing wood species, namely, Enterolobium cyclocarpum, Paraserianthes falcataria, Shorea sp., Toona sinensis, Gmelina arborea, Pinus merkusii, Acacia mangium, and Acacia hybrid obtained from the tropical region. The wettability test was conducted by contact angle measurement, while the adhesion performance was expressed by strength retention (SR) and wood failure (WF) percentages through block shear tested under the Japanese Agricultural Standard (JAS). Results showed that smaller contact angle for P. falcataria followed by E. cyclocarpum, P. merkusii, T. sinensis, and Shorea indicated that the surfaces were easier to be glued than that of G. arborea, A. mangium, and A. hybrid. It is indicated that high wettability of P. falcataria, E. cyclocarpum, P. merkusii, T. sinensis, and Shorea resulted in the better adhesive spread and more intimate contact between the wood surface and the adhesive as shown by their high SR with high WF percentages.