João Machado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
João Machado has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Nuno Correia
INEGI—Institute of Science and Innovation in Mechanical and Industrial Engineering, 4200-465 Porto, Portugal
2 shared publications A. B. Albayraktar
Koç University Istanbul Turkey
1 shared publicationA. Endruweit
University of Nottingham Faculty of Engineering Nottingham UK
1 shared publicationA. Leitão
INEGI, Campus da FEUP Porto Portugal
1 shared publication- Adélio Mendes
University of Porto Rua Dr. Roberto Frias
1 shared publication C. Binetruy
France Nantes Université Ecole Centrale de Nantes, CNRS, GeM, UMR 6183 Nantes France
1 shared publication
Latest Publications
- 26 February 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S2)
Benchmarking Permeability Predictions for an Engineered Reference Medium: Toward Calibration of Permeability Rigs
Accurate permeability prediction in fibrous media is essential for modeling liquid composite manufacturing processes, yet numerical predictions are often inconsistent owing to modeling assumptions and numerical implementation choices. This work introduces a 3D‐printable anisotropic reference porous medium designed to reproduce the main flow pathways and anisotropy trends observed in textile reinforcements, while avoiding the inherent variability of real fabrics. The idealized geometry provides a well‐controlled, reproducible benchmark for permeability prediction, acknowledging that it does not capture fine‐scale features such as intra‐tow pores or fiber surface curvature, and may have higher absolute permeability values than real textiles. Fourteen research groups independently simulated fully saturated, incompressible, laminar, and steady‐state flow through a given CAD‐based medium using their own numerical setups. While simple analytical flows (e.g., laminar flow in a pipe or slit) can validate individual codes, they are insufficient to capture the complexity and anisotropy of textile‐like porous media. Benchmarking is therefore necessary to reveal real‐world variability in permeability predictions. Results show good consistency for in‐plane permeability ( K xx : mean 2.75 × 10 −9 m 2 , CoV = 0.105; K zz : mean 6.8 × 10 −10 m 2 , CoV = 0.205), while out‐of‐plane permeability ( K yy ) shows much higher variability (unit‐cell mean 1.40 × 10 −10 m 2 , CoV = 0.790; periodic‐assembly mean 1.27 × 10 −10 m 2 , CoV = 0.470). These findings (i) demonstrate the feasibility of using idealized additive‐manufactured porous media as reproducible calibration benchmarks and (ii) highlight the value of cross‐validation across multiple numerical platforms to bolster confidence in permeability prediction for composite manufacturing.
- 26 February 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S2)
Benchmarking Permeability Predictions for an Engineered Reference Medium: Toward Calibration of Permeability Rigs
Accurate permeability prediction in fibrous media is essential for modeling liquid composite manufacturing processes, yet numerical predictions are often inconsistent owing to modeling assumptions and numerical implementation choices. This work introduces a 3D‐printable anisotropic reference porous medium designed to reproduce the main flow pathways and anisotropy trends observed in textile reinforcements, while avoiding the inherent variability of real fabrics. The idealized geometry provides a well‐controlled, reproducible benchmark for permeability prediction, acknowledging that it does not capture fine‐scale features such as intra‐tow pores or fiber surface curvature, and may have higher absolute permeability values than real textiles. Fourteen research groups independently simulated fully saturated, incompressible, laminar, and steady‐state flow through a given CAD‐based medium using their own numerical setups. While simple analytical flows (e.g., laminar flow in a pipe or slit) can validate individual codes, they are insufficient to capture the complexity and anisotropy of textile‐like porous media. Benchmarking is therefore necessary to reveal real‐world variability in permeability predictions. Results show good consistency for in‐plane permeability ( K xx : mean 2.75 × 10 −9 m 2 , CoV = 0.105; K zz : mean 6.8 × 10 −10 m 2 , CoV = 0.205), while out‐of‐plane permeability ( K yy ) shows much higher variability (unit‐cell mean 1.40 × 10 −10 m 2 , CoV = 0.790; periodic‐assembly mean 1.27 × 10 −10 m 2 , CoV = 0.470). These findings (i) demonstrate the feasibility of using idealized additive‐manufactured porous media as reproducible calibration benchmarks and (ii) highlight the value of cross‐validation across multiple numerical platforms to bolster confidence in permeability prediction for composite manufacturing.
- Open Access
- 3 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10690
The Development of Data-Driven Algorithms and Models for Monitoring Void Transport in Liquid Composite Molding Using a 3D-Printed Porous Media
In Liquid Composite Molding (LCM), the high variability present in reinforcement properties such as permeability creates additional challenges during the injection process, such as void formation. Although improved injection strategy designs can mitigate the formation of defects, these processes can benefit from real-time process monitoring and control to adapt the injection conditions when needed. In this study, a machine vision algorithm is proposed, with the objective of detecting and tracking both fluid flow and bubbles in an LCM setup. In this preliminary design, 3D-printed porous geometries are used to mimic the architecture of textile reinforcements. The results confirm the applicability of the proposed approach, as the detection and tracking of the objects of interest is possible, without the need to incur in elaborate experimental preparations, such as coloring the fluid to increase contrast, or complex lighting conditions. Additionally, the proposed approach allowed for the formulation of a new dimensionless number to characterize bubble transport efficiency, offering a quantitative metric for evaluating void transport dynamics. This research underscores the potential of data-driven approaches in addressing manufacturing challenges in LCM by reducing the overall process monitoring complexity, as well as using the acquired reliable data to develop robust, data-driven models that offer new understanding of process dynamics and contribute to improving manufacturing efficiency.
- 3 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10690
Open AccessThe Development of Data-Driven Algorithms and Models for Monitoring Void Transport in Liquid Composite Molding Using a 3D-Printed Porous Media
In Liquid Composite Molding (LCM), the high variability present in reinforcement properties such as permeability creates additional challenges during the injection process, such as void formation. Although improved injection strategy designs can mitigate the formation of defects, these processes can benefit from real-time process monitoring and control to adapt the injection conditions when needed. In this study, a machine vision algorithm is proposed, with the objective of detecting and tracking both fluid flow and bubbles in an LCM setup. In this preliminary design, 3D-printed porous geometries are used to mimic the architecture of textile reinforcements. The results confirm the applicability of the proposed approach, as the detection and tracking of the objects of interest is possible, without the need to incur in elaborate experimental preparations, such as coloring the fluid to increase contrast, or complex lighting conditions. Additionally, the proposed approach allowed for the formulation of a new dimensionless number to characterize bubble transport efficiency, offering a quantitative metric for evaluating void transport dynamics. This research underscores the potential of data-driven approaches in addressing manufacturing challenges in LCM by reducing the overall process monitoring complexity, as well as using the acquired reliable data to develop robust, data-driven models that offer new understanding of process dynamics and contribute to improving manufacturing efficiency.
- 27 March 2012
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 9 (3) , 365-374
Characterization of a water-based paint for corrosion protection
- 27 March 2012
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 9 (3) , 365-374
Characterization of a water-based paint for corrosion protection