Muhammad Khawar Nadeem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Muhammad Khawar Nadeem has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Bilawal Ali
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
16 shared publications - Yubin Gong
University of Electronic Science and Technology of China
16 shared publications - Atif Jameel
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
13 shared publications - Jibran Latif
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
13 shared publications - Zhanliang Wang
University of Electronic Science and Technology of China
11 shared publications - Shaomeng Wang
University of Electronic Science and Technology of China
9 shared publications
Latest Publications
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 646-651
An Efficient Blended Staggered Double Vane Slow Wave Structure for 1 THz TWT
This article presents a novel blended staggered double vane slow wave structure (BSDV-SWS) for a 0.98–1.1THz frequency traveling-wave tube (TWT). The proposed structure is designed to overcome key limitations at terahertz frequencies by enhancing electric field distribution for improved interaction efficiency, simplifying fabrication through the elimination of sharp edges that cause field singularities, and reducing RF losses. Dispersion and transmission analyses confirm minimal reflection and strong energy transfer. Beam–wave interaction provides 1.155 W output power, 25.85dB gain, and 0.25% electronic efficiency when 25.7kV beam voltage and 18.2mA beam current is applied using CST Studio Suite. The close alignment between the measured S-parameters of the nano-computer numerical control (CNC)-fabricated device and the simulated performance confirms the practical feasibility of the proposed design.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 646-651
An Efficient Blended Staggered Double Vane Slow Wave Structure for 1 THz TWT
This article presents a novel blended staggered double vane slow wave structure (BSDV-SWS) for a 0.98–1.1THz frequency traveling-wave tube (TWT). The proposed structure is designed to overcome key limitations at terahertz frequencies by enhancing electric field distribution for improved interaction efficiency, simplifying fabrication through the elimination of sharp edges that cause field singularities, and reducing RF losses. Dispersion and transmission analyses confirm minimal reflection and strong energy transfer. Beam–wave interaction provides 1.155 W output power, 25.85dB gain, and 0.25% electronic efficiency when 25.7kV beam voltage and 18.2mA beam current is applied using CST Studio Suite. The close alignment between the measured S-parameters of the nano-computer numerical control (CNC)-fabricated device and the simulated performance confirms the practical feasibility of the proposed design.
- 29 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 6300-6306
A Sheet Beam-Operated Gridless Inductive Output Tube With Metamaterial-Inspired Cavity
Metamaterial-based structures offer the potential to significantly miniaturize vacuum electron devices. This property is desirable for the gridless inductive output tube (IOT), due to its primary application as a compact high-power amplifier. This article presents a novel sheet beam-driven gridless IOT with a metamaterial-inspired cavity. The 922-MHz rectangular cavity is loaded with four complementary split-ring resonator (CSRR) cells. Power is extracted with a loop coupled to the magnetic field of the TM11 mode. The analytical model of the cavityand CSRR cells is derived using an equivalent circuit, and compared to the simulation results. Eigenmode and time-domain simulations show $\pi $ -mode operation, double negative behavior, and an external quality factor ( ${Q}_{e}$ ) of 96.6. A cold test of the cavity is performed to experimentally verify the scattering parameters. The 45-kV, 16.8-A electron beam is focused with a 0.35-T magnetic field and density-modulated using a 1-kV sinusoidal signal. Particle-in-cell simulations of the IOT show an average output of 250kW and 27-dB gain. Compared to a cavity of standard waveguide dimensions at 922 MHz, the metamaterial-based design offers a 73.9% reduction in cross-sectional area.
- 29 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 6300-6306
A Sheet Beam-Operated Gridless Inductive Output Tube With Metamaterial-Inspired Cavity
Metamaterial-based structures offer the potential to significantly miniaturize vacuum electron devices. This property is desirable for the gridless inductive output tube (IOT), due to its primary application as a compact high-power amplifier. This article presents a novel sheet beam-driven gridless IOT with a metamaterial-inspired cavity. The 922-MHz rectangular cavity is loaded with four complementary split-ring resonator (CSRR) cells. Power is extracted with a loop coupled to the magnetic field of the TM11 mode. The analytical model of the cavityand CSRR cells is derived using an equivalent circuit, and compared to the simulation results. Eigenmode and time-domain simulations show $\pi $ -mode operation, double negative behavior, and an external quality factor ( ${Q}_{e}$ ) of 96.6. A cold test of the cavity is performed to experimentally verify the scattering parameters. The 45-kV, 16.8-A electron beam is focused with a 0.35-T magnetic field and density-modulated using a 1-kV sinusoidal signal. Particle-in-cell simulations of the IOT show an average output of 250kW and 27-dB gain. Compared to a cavity of standard waveguide dimensions at 922 MHz, the metamaterial-based design offers a 73.9% reduction in cross-sectional area.
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (5) , 903-913
Analytical Modeling, Simulation, and Cold Testing of a Radial SWS for THz Applications
This paper presents the analytical design, simulation, and cold-test validation of a radial slow-wave structure for terahertz applications, addressing the limitations of conventional axial designs. Radial vacuum electron devices enhance the interaction area, reduce space charge effects, and enable compact, magnetic field-free operation, making them well-suited for high-power THz sources. A mathematical framework is developed to derive dispersion equations for the radial configuration, and numerical simulations to analyze the dispersion characteristics, external quality factor, and interaction impedance. A radial backward wave oscillator (BWO) is designed to validate the analytical model at 0.65 THz. Its performance is evaluated through particle-in-cell simulations, which model the interaction between the diverging radial sheet electron beam (RSEB) and the electromagnetic wave. The particle simulation confirms that the radial BWO operates without an external magnetic field, achieving a peak output power of 46.4 W at 0.651 THz using a 20.2 kV, 400 mA electron beam. A matched TEM-TE$_{10}$ mode converter is designed to extract the RF power efficiently for practical applications. The proposed BWO, comprising 40 periods and an integrated mode converter, is fabricated with precise surface finishing, dimensional accuracy, and compatibility with THz operational requirements. Cold-test of the BWO with mode converter shows an S$_{11}$ parameter of approximately -13dB at the desired frequencies, closely matching the simulated results. These findings highlight the potential of radial BWO as compact, high-power THz sources, enabling stable and efficient operation for advanced applications.
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (5) , 903-913
Analytical Modeling, Simulation, and Cold Testing of a Radial SWS for THz Applications
This paper presents the analytical design, simulation, and cold-test validation of a radial slow-wave structure for terahertz applications, addressing the limitations of conventional axial designs. Radial vacuum electron devices enhance the interaction area, reduce space charge effects, and enable compact, magnetic field-free operation, making them well-suited for high-power THz sources. A mathematical framework is developed to derive dispersion equations for the radial configuration, and numerical simulations to analyze the dispersion characteristics, external quality factor, and interaction impedance. A radial backward wave oscillator (BWO) is designed to validate the analytical model at 0.65 THz. Its performance is evaluated through particle-in-cell simulations, which model the interaction between the diverging radial sheet electron beam (RSEB) and the electromagnetic wave. The particle simulation confirms that the radial BWO operates without an external magnetic field, achieving a peak output power of 46.4 W at 0.651 THz using a 20.2 kV, 400 mA electron beam. A matched TEM-TE$_{10}$ mode converter is designed to extract the RF power efficiently for practical applications. The proposed BWO, comprising 40 periods and an integrated mode converter, is fabricated with precise surface finishing, dimensional accuracy, and compatibility with THz operational requirements. Cold-test of the BWO with mode converter shows an S$_{11}$ parameter of approximately -13dB at the desired frequencies, closely matching the simulated results. These findings highlight the potential of radial BWO as compact, high-power THz sources, enabling stable and efficient operation for advanced applications.
- 10 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1455-1461
Design and Cold Test of a Broadly Tunable Terahertz Short Double-Grating Rectangular Waveguide Slow Wave Structure
A short double-grating rectangular waveguide (DGRW) slow wave structure (SWS) is designed and compared in detail with DGRW. Significant modifications are made to the corrugation geometry to optimize the dispersion characteristics, resulting in a broader frequency passband and enhanced frequency tunability. The high-frequency performance is analyzed in terms of dispersion and interaction impedance. The structure shows an interaction impedance of 1.5 Ω at 0.34 THz. To confirm the effectiveness of the proposed design, a 0.34-THz backward wave oscillator circuit is designed and fabricated comprising 160 periods. The circuit is assembled and cold-tested for scattering parameters. The results show S21 values above -1.5 dB and S11 below -20 dB for a broad frequency range. The beam–wave interaction simulations using a 30-kV, 30-mA electron beam, and 0.2-T focusing magnetic field show that the backward wave oscillator based on the proposed design achieves an average output power of 16 W at 0.34 THz, with a frequency tuning range of 95 GHz when compared with 57 GHz for the DGRW-based backward wave oscillator.
- 10 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1455-1461
Design and Cold Test of a Broadly Tunable Terahertz Short Double-Grating Rectangular Waveguide Slow Wave Structure
A short double-grating rectangular waveguide (DGRW) slow wave structure (SWS) is designed and compared in detail with DGRW. Significant modifications are made to the corrugation geometry to optimize the dispersion characteristics, resulting in a broader frequency passband and enhanced frequency tunability. The high-frequency performance is analyzed in terms of dispersion and interaction impedance. The structure shows an interaction impedance of 1.5 Ω at 0.34 THz. To confirm the effectiveness of the proposed design, a 0.34-THz backward wave oscillator circuit is designed and fabricated comprising 160 periods. The circuit is assembled and cold-tested for scattering parameters. The results show S21 values above -1.5 dB and S11 below -20 dB for a broad frequency range. The beam–wave interaction simulations using a 30-kV, 30-mA electron beam, and 0.2-T focusing magnetic field show that the backward wave oscillator based on the proposed design achieves an average output power of 16 W at 0.34 THz, with a frequency tuning range of 95 GHz when compared with 57 GHz for the DGRW-based backward wave oscillator.
- 14 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 417-423
Design and Cold Testing of a Bi-Periodic Angular Radial RF Circuit for a C-Band Extended Interaction Oscillator
A C -band angular bi-periodic angular radial EIO (BPAREIO) is proposed for high-power microwave (HPM) applications. It offers miniaturization, high efficiency, and low magnetic field operation. A divergent angular radial sheet electron beam (ARSEB) with an angle of 14 $^{\circ}$ and a current of 101 A is employed to operate the seven-gap angular radial cavities. Angular radial cavities are coupled by two sectoral cavities having an opening angle $\beta$ . Cavity characteristics, such as dispersion, scattering parameters, normalized beam conductance, electric field distribution, and stability, are analyzed to optimize the design for $\pi$ -mode operation. To further enhance the performance of BPAREIO, ridges are incorporated into interaction gaps near the beam tunnel. This modification leads to an enhanced radial electric field near the beam tunnel, increasing characteristic impedance ( R/Q ). In particle-in cell (PIC) simulations, ridge-loaded BPAREIO demonstrated in modeling an RF peak output power of 6.2 MW at a frequency of 5.805 GHz when applying a beam voltage of 89 kV and a magnetic field of 0.3 T, yielding a peak power efficiency of 69.5%. In contrast, the BPAREIO without ridges expected a peak output power of 5.4 MW and an efficiency of 59.5% at 5.885 GHz, using the same beam parameters. Consequently, the ridge-loaded BPAREIO predicted a 16.7% increase in peak electronic efficiency compared with the BPAREIO without ridges. Moreover, ridge-loaded BPAREIO is fabricated, and experimental results closely match those obtained from simulation.
- 14 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 417-423
Design and Cold Testing of a Bi-Periodic Angular Radial RF Circuit for a C-Band Extended Interaction Oscillator
A C -band angular bi-periodic angular radial EIO (BPAREIO) is proposed for high-power microwave (HPM) applications. It offers miniaturization, high efficiency, and low magnetic field operation. A divergent angular radial sheet electron beam (ARSEB) with an angle of 14 $^{\circ}$ and a current of 101 A is employed to operate the seven-gap angular radial cavities. Angular radial cavities are coupled by two sectoral cavities having an opening angle $\beta$ . Cavity characteristics, such as dispersion, scattering parameters, normalized beam conductance, electric field distribution, and stability, are analyzed to optimize the design for $\pi$ -mode operation. To further enhance the performance of BPAREIO, ridges are incorporated into interaction gaps near the beam tunnel. This modification leads to an enhanced radial electric field near the beam tunnel, increasing characteristic impedance ( R/Q ). In particle-in cell (PIC) simulations, ridge-loaded BPAREIO demonstrated in modeling an RF peak output power of 6.2 MW at a frequency of 5.805 GHz when applying a beam voltage of 89 kV and a magnetic field of 0.3 T, yielding a peak power efficiency of 69.5%. In contrast, the BPAREIO without ridges expected a peak output power of 5.4 MW and an efficiency of 59.5% at 5.885 GHz, using the same beam parameters. Consequently, the ridge-loaded BPAREIO predicted a 16.7% increase in peak electronic efficiency compared with the BPAREIO without ridges. Moreover, ridge-loaded BPAREIO is fabricated, and experimental results closely match those obtained from simulation.
- 13 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4553-4561
Ridge-Loaded S-Band MILO Using Drift Tube and Dual Extraction Cavity
A magnetically insulated line oscillator (MILO) is a unique high-power microwave (HPM) device distinct by its inherent ability to generate a self-insulating magnetic field. In this article, an S -band ridge-loaded MILO is studied. The current design incorporates a drift section in a region of slow wave structure (SWS), resulting in a reduction of the axial velocity ( $v_z$ ) spread of the modulated beam. Another, a dual extraction cavity is designed in the extraction region. So, the axial electric field is enhanced, and beam–wave interaction is lengthened in this region; consequently, efficiency is increased. Dispersion characteristic is obtained in eigenmode analysis. In 3-D particle-in-cell simulation, the presented MILO generates a 4.5-GW average output power at 2.56-GHz frequency with an application of 500-kV voltage and a current of 42 kA. The average efficiency is elevated to 21.4%, while it is only 15.7% for conventional ridge-loaded MILO for the same input parameters, so the net increase in efficiency is 36%.
- 13 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4553-4561
Ridge-Loaded S-Band MILO Using Drift Tube and Dual Extraction Cavity
A magnetically insulated line oscillator (MILO) is a unique high-power microwave (HPM) device distinct by its inherent ability to generate a self-insulating magnetic field. In this article, an S -band ridge-loaded MILO is studied. The current design incorporates a drift section in a region of slow wave structure (SWS), resulting in a reduction of the axial velocity ( $v_z$ ) spread of the modulated beam. Another, a dual extraction cavity is designed in the extraction region. So, the axial electric field is enhanced, and beam–wave interaction is lengthened in this region; consequently, efficiency is increased. Dispersion characteristic is obtained in eigenmode analysis. In 3-D particle-in-cell simulation, the presented MILO generates a 4.5-GW average output power at 2.56-GHz frequency with an application of 500-kV voltage and a current of 42 kA. The average efficiency is elevated to 21.4%, while it is only 15.7% for conventional ridge-loaded MILO for the same input parameters, so the net increase in efficiency is 36%.
- 1 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4544-4552
A Ka-Band Radial Beam Oscillator With Phase-Velocity Tapering
This research article presents a high-power radial oscillator in the $Ka$ -band equipped with a radial sheet electron beam. Radial beam devices outperform traditional devices by offering more extensive interaction spaces and reduced space charge effects. This advantage eliminates the necessity for external magnetic fields, efficiently solving the efficiency issues. The design parameters of the presented device for efficient operation in $\pi$ mode within the $Ka$ -band frequency spectrum are identified through numerical analysis. The baseline model with a constant period is simulated using particle-in-cell (PIC) solver, and importantly, without an external magnetic field. The simulation features a radial beam cathode with an emission area of 2 $\pi$ $\times$ 107.5 $\times$ 0.7 mm, generating a current density of 444.37 A/cm $^2$ . At 160-and 170-kV beam voltage, the device achieves efficiencies of 31.05% and 38.5%, with peak powers of 104.3 and 137.8 MW, respectively, while maintaining stable signal frequencies around 34.6 and 34.62 GHz. The baseline model’s performance is further enhanced through various phase-velocity tapering techniques, including linear, exponential, and logarithmic methods. The impact of these velocity tapering approaches on beam–wave interaction is analyzed. Linear tapering, in particular, improves output power to 190.61 MW and efficiency to 53.39%, exceeding the constant period model’s 137.8 MW power and 38.5% efficiency. Although exponential and logarithmic methods also boost efficiency, they are less effective than the linear approach. These tapering techniques lead to minor frequency shifts, indicating their structural influence on the oscillator’s performance.
- 1 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4544-4552
A Ka-Band Radial Beam Oscillator With Phase-Velocity Tapering
This research article presents a high-power radial oscillator in the $Ka$ -band equipped with a radial sheet electron beam. Radial beam devices outperform traditional devices by offering more extensive interaction spaces and reduced space charge effects. This advantage eliminates the necessity for external magnetic fields, efficiently solving the efficiency issues. The design parameters of the presented device for efficient operation in $\pi$ mode within the $Ka$ -band frequency spectrum are identified through numerical analysis. The baseline model with a constant period is simulated using particle-in-cell (PIC) solver, and importantly, without an external magnetic field. The simulation features a radial beam cathode with an emission area of 2 $\pi$ $\times$ 107.5 $\times$ 0.7 mm, generating a current density of 444.37 A/cm $^2$ . At 160-and 170-kV beam voltage, the device achieves efficiencies of 31.05% and 38.5%, with peak powers of 104.3 and 137.8 MW, respectively, while maintaining stable signal frequencies around 34.6 and 34.62 GHz. The baseline model’s performance is further enhanced through various phase-velocity tapering techniques, including linear, exponential, and logarithmic methods. The impact of these velocity tapering approaches on beam–wave interaction is analyzed. Linear tapering, in particular, improves output power to 190.61 MW and efficiency to 53.39%, exceeding the constant period model’s 137.8 MW power and 38.5% efficiency. Although exponential and logarithmic methods also boost efficiency, they are less effective than the linear approach. These tapering techniques lead to minor frequency shifts, indicating their structural influence on the oscillator’s performance.
- 30 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6380-6387
Design and Performance Evaluation of aKa-Band Radial Staggered Double Vane Backward Wave Oscillator
This article introduces a radial staggered double vane (RSDV) backward wave oscillator (BWO) using a radial sheet electron beam (RSEB) to overcome the limitations of traditional $\textit{Ka}$ -band BWOs. Traditional BWOs face limitations due to a decrease in interaction space as frequency increases, leading to lower efficiency and considerable challenges in mitigating thermal stresses. In addition, these devices typically require an external magnetic field for beam focusing to counteract space charge effects, adding complexity to their fabrication. The RSDV slow wave structure (SWS) is designed, and its high-frequency characteristics are numerically analyzed. Particle-in-cell (PIC) simulations are conducted for the RSDV BWO using a converging RSEB without an external magnetic field, at a beam voltage of 20 kV and a current density of 22.43 A/cm $^\text{2}$ . The device demonstrates enhanced efficiency over traditional $\textit{Ka}$ -band BWOs, achieving an average power of 117.61 kW and an efficiency of 10.69% at 31.02 GHz. Furthermore, the performance using a diverging RSEB setup is evaluated and compared with that of a converging RSEB. Coupled particle-thermal simulation confirms the device’s capability to effectively manage thermal stresses. The device, consisting of 18 periods, is fabricated and tested; cold-test results indicate an S $_{\text{11}}$ parameter around $-$ 10 dB at desired frequencies, aligning with simulated results. Moreover, a comparison between analytical, simulated, and measured dispersion curves based on S $_{\text{11}}$ phase is provided.
- 30 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (10) , 6380-6387
Design and Performance Evaluation of aKa-Band Radial Staggered Double Vane Backward Wave Oscillator
This article introduces a radial staggered double vane (RSDV) backward wave oscillator (BWO) using a radial sheet electron beam (RSEB) to overcome the limitations of traditional $\textit{Ka}$ -band BWOs. Traditional BWOs face limitations due to a decrease in interaction space as frequency increases, leading to lower efficiency and considerable challenges in mitigating thermal stresses. In addition, these devices typically require an external magnetic field for beam focusing to counteract space charge effects, adding complexity to their fabrication. The RSDV slow wave structure (SWS) is designed, and its high-frequency characteristics are numerically analyzed. Particle-in-cell (PIC) simulations are conducted for the RSDV BWO using a converging RSEB without an external magnetic field, at a beam voltage of 20 kV and a current density of 22.43 A/cm $^\text{2}$ . The device demonstrates enhanced efficiency over traditional $\textit{Ka}$ -band BWOs, achieving an average power of 117.61 kW and an efficiency of 10.69% at 31.02 GHz. Furthermore, the performance using a diverging RSEB setup is evaluated and compared with that of a converging RSEB. Coupled particle-thermal simulation confirms the device’s capability to effectively manage thermal stresses. The device, consisting of 18 periods, is fabricated and tested; cold-test results indicate an S $_{\text{11}}$ parameter around $-$ 10 dB at desired frequencies, aligning with simulated results. Moreover, a comparison between analytical, simulated, and measured dispersion curves based on S $_{\text{11}}$ phase is provided.
- 9 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (10) , 1989-1992
A Novel Quadruple Corrugated Waveguide Slow-Wave Structure for Terahertz Applications
A novel quadruple corrugated waveguide slow-wave structure for terahertz radiation sources has been proposed, designed for pencil and sheet electron beams. It is compared in detail with a double corrugated waveguide slow-wave structure in terms of dispersion, interaction impedance, and output power. High-frequency characteristics show an interaction impedance of 0.77 Ω for quadruple corrugated waveguide sheet electron beam tunnel, 0.55 Ω for quadruple corrugated waveguide pencil electron beam tunnel, and 0.5 Ω for double corrugated waveguide at 0.34 THz. To validate the proposed slow-wave structure, a 0.34 THz backward wave oscillator is designed, with a sheet electron beam producing 6.3 W peak power and frequency tunability from 0.281-0.368 THz, and a pencil beam generating 2.6 W peak power with frequency tunability from 0.286-0.365 THz. The double corrugated waveguide-based BWO shows an output power of 2.2 W. 160 periods of the quadruple corrugated waveguide slow-wave structure are fabricated using a computer numerical control milling machine. Cold test experiments show S 21 above -2 dB and S 11 below -16 dB at 0.34 THz.
- 9 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (10) , 1989-1992
A Novel Quadruple Corrugated Waveguide Slow-Wave Structure for Terahertz Applications
A novel quadruple corrugated waveguide slow-wave structure for terahertz radiation sources has been proposed, designed for pencil and sheet electron beams. It is compared in detail with a double corrugated waveguide slow-wave structure in terms of dispersion, interaction impedance, and output power. High-frequency characteristics show an interaction impedance of 0.77 Ω for quadruple corrugated waveguide sheet electron beam tunnel, 0.55 Ω for quadruple corrugated waveguide pencil electron beam tunnel, and 0.5 Ω for double corrugated waveguide at 0.34 THz. To validate the proposed slow-wave structure, a 0.34 THz backward wave oscillator is designed, with a sheet electron beam producing 6.3 W peak power and frequency tunability from 0.281-0.368 THz, and a pencil beam generating 2.6 W peak power with frequency tunability from 0.286-0.365 THz. The double corrugated waveguide-based BWO shows an output power of 2.2 W. 160 periods of the quadruple corrugated waveguide slow-wave structure are fabricated using a computer numerical control milling machine. Cold test experiments show S 21 above -2 dB and S 11 below -16 dB at 0.34 THz.
- Open Access
- 1 August 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (8)
Multipactor analysis of 431 MHz L-shaped inductive output tube cavity
Gridless inductive output tubes (IOTs) offer compact size and high-power amplification at sub-GHz frequencies. Minimizing cavity dimensions in the interest of compactness leads to smaller gaps, which may cause multipactor discharge under high-power operating conditions. The uncontrolled electron growth resulting from multipactor breakdown can lead to undesired effects including surface damage and system failure. This paper performs a parallel-plate multipactor analysis for a high-Q, L-shaped, aluminum, 431 MHz cavity designed for a gridless IOT to be operated in the MW-power regime. The cavity gap is 27 mm, and diameter is 339 mm. Multipactor susceptibility regions are calculated for non-zero emission energy, half-cycle, and non-half-cycle multipactor using a semi-analytic approach and a standard aluminum secondary electron yield (SEY) curve. The analytical results are validated with particle-in-cell simulation in CST Studio. Simulation results show a voltage range of 6.4–19 kV, compared to the analytically calculated values of 8.2 and 18.3 kV for the lower and upper bounds, respectively. Fluorocarbon coating as a means to reduce secondary electron emission is simulated, which shows 46% reduction in peak particle population with an 11.2 nm PTFE coating, with further reduction as coating thickness increases. The results show that the L-shaped cavity is a suitable choice for this IOT design as it does not exhibit single-surface multipactor and will not develop two-surface multipactor at full-power operation.
- 1 August 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (8)
Open AccessMultipactor analysis of 431 MHz L-shaped inductive output tube cavity
Gridless inductive output tubes (IOTs) offer compact size and high-power amplification at sub-GHz frequencies. Minimizing cavity dimensions in the interest of compactness leads to smaller gaps, which may cause multipactor discharge under high-power operating conditions. The uncontrolled electron growth resulting from multipactor breakdown can lead to undesired effects including surface damage and system failure. This paper performs a parallel-plate multipactor analysis for a high-Q, L-shaped, aluminum, 431 MHz cavity designed for a gridless IOT to be operated in the MW-power regime. The cavity gap is 27 mm, and diameter is 339 mm. Multipactor susceptibility regions are calculated for non-zero emission energy, half-cycle, and non-half-cycle multipactor using a semi-analytic approach and a standard aluminum secondary electron yield (SEY) curve. The analytical results are validated with particle-in-cell simulation in CST Studio. Simulation results show a voltage range of 6.4–19 kV, compared to the analytically calculated values of 8.2 and 18.3 kV for the lower and upper bounds, respectively. Fluorocarbon coating as a means to reduce secondary electron emission is simulated, which shows 46% reduction in peak particle population with an 11.2 nm PTFE coating, with further reduction as coating thickness increases. The results show that the L-shaped cavity is a suitable choice for this IOT design as it does not exhibit single-surface multipactor and will not develop two-surface multipactor at full-power operation.