Charafeddine Beldjani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Charafeddine Beldjani has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Aymen Kethiri
Department of Civil and Environmental Engineering, DICA, Politecnico di Milano, Milan, Italy
5 shared publications Kamel Aoues
Laboratoire de Génie Energétique et Matériaux, LGEM, Université de Biskra, B.P.145 R.P., 07000, Biskra, Algeria
3 shared publicationsYousra Boutera
Laboratoire de Génie Mécanique, LGM, Université de Biskra, B.P.145 R.P., 07000, Biskra, Algeria
3 shared publications- Yousra Boutera
Laboratoire de Génie Mécanique, LGM, Université de Biskra, B.P.145 R.P. 07000 Biskra, Algeria
3 shared publications Nora Boultif
2 shared publicationsNoureddine Belghar
Laboratoire de Génie Energétique et Matériaux, LGEM, Université de Biskra, B.P.145 R.P., 07000, Biskra, Algeria
2 shared publications
Latest Publications
- 26 December 2025
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (1) , 523-550
CFD analysis on thermo-hydraulic performance behavior of an indirect solar dryer containing various configurations of rectangular ribs
- 26 December 2025
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (1) , 523-550
CFD analysis on thermo-hydraulic performance behavior of an indirect solar dryer containing various configurations of rectangular ribs
- Open Access
- 10 April 2025
- Published by University of Biskra in Journal of Applied Engineering Science and Technology
- Vol. 5 (1)
CFD Analysis of Hybrid Photovoltaic Thermal (PV/Th) Solar Collector Efficiency Incorporating Ag-AL2O3/water Hybrid Nanofluids
The optimization of energy consumption is closely tied to enhancing the power output of photovoltaic panels. This study offers a numerical investigation of the utilization of hybrid nanofluids (Ag-Al2O3-water) as a cooling fluid in a hybrid photovoltaic thermal (PV/Th) collector, aiming to improve electrical performance by lowering the PV cells operating temperature. The hybrid PV/Th collector comprises a photovoltaic panel (PV) coupled with a thermal collector, including a heat sink equipped with rectangular ribs positioned at the bottom of the PV module. This research explores the impact of critical configuration parameters, such as inlet velocities of working fluid and nanoparticle volume fractions, on the Nu number, PV cell temperature, and both thermal and electrical efficiencies within steady-state operating conditions. The 3D numerical simulation to analyze the overall performance of a hybrid PV/Th collector was conducted using ANSYS Fluent software version 17.1. The numerical findings demonstrate that increasing the nanoparticle volume fraction elevates the cooling fluid's thermal conductivity, consequently enhancing the heat transfer by conduction. Furthermore, higher coolant velocities enhance heat transfer by convection, resulting in a more effective heat transfer rate within the PV/Th system. This, in turn, reduces the operating temperature and significantly enhances the hybrid PV/Th system's overall performance. Highlights Hybrid nanofluid cooling reduces PV cell temp and boosts overall system efficiency. Higher Re numbers and nanoparticle loads enhance thermal and electrical performance. ANSYS CFD showed max total efficiency of 44.7% at Re = 800, Φ = 0.06. Ag-Al2O3 nanofluid outperformed water alone in PV/Th heat transfer. PV cell temp dropped from 60.1°C to 40.6°C using nanofluid at high flow rate.
- 10 April 2025
- Published by University of Biskra in Journal of Applied Engineering Science and Technology
- Vol. 5 (1)
Open AccessCFD Analysis of Hybrid Photovoltaic Thermal (PV/Th) Solar Collector Efficiency Incorporating Ag-AL2O3/water Hybrid Nanofluids
The optimization of energy consumption is closely tied to enhancing the power output of photovoltaic panels. This study offers a numerical investigation of the utilization of hybrid nanofluids (Ag-Al2O3-water) as a cooling fluid in a hybrid photovoltaic thermal (PV/Th) collector, aiming to improve electrical performance by lowering the PV cells operating temperature. The hybrid PV/Th collector comprises a photovoltaic panel (PV) coupled with a thermal collector, including a heat sink equipped with rectangular ribs positioned at the bottom of the PV module. This research explores the impact of critical configuration parameters, such as inlet velocities of working fluid and nanoparticle volume fractions, on the Nu number, PV cell temperature, and both thermal and electrical efficiencies within steady-state operating conditions. The 3D numerical simulation to analyze the overall performance of a hybrid PV/Th collector was conducted using ANSYS Fluent software version 17.1. The numerical findings demonstrate that increasing the nanoparticle volume fraction elevates the cooling fluid's thermal conductivity, consequently enhancing the heat transfer by conduction. Furthermore, higher coolant velocities enhance heat transfer by convection, resulting in a more effective heat transfer rate within the PV/Th system. This, in turn, reduces the operating temperature and significantly enhances the hybrid PV/Th system's overall performance. Highlights Hybrid nanofluid cooling reduces PV cell temp and boosts overall system efficiency. Higher Re numbers and nanoparticle loads enhance thermal and electrical performance. ANSYS CFD showed max total efficiency of 44.7% at Re = 800, Φ = 0.06. Ag-Al2O3 nanofluid outperformed water alone in PV/Th heat transfer. PV cell temp dropped from 60.1°C to 40.6°C using nanofluid at high flow rate.
- Open Access
- 4 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (7) , 3015
Experimental Study on the Effect of Date Palm Powder on the Thermal and Physico-Mechanical Properties of Gypsum Mortars
Date palm leaves have been diachronically applied in building materials in the Middle East and North Africa (MENA) region, so as to enhance specific properties, such as volume stability and strength. This research work concerns an experimental study on the impact of date palm leaflet powder (DPLP) on the thermal and physico-mechanical properties of gypsum mortars. A series of mortar compositions were prepared with different proportions of DPLP (0, 1, 3, and 5% w/w of binder) and variant particle size (0.5, 1, and 1.5 mm). The results showed that the mortars containing DPLP exhibited significant changes in their properties due to variations in DPLP concentration and particle size. Increased DPLP led to lower density, higher porosity, and water absorption rate, whereas mechanical strength and thermal conductivity were decreased according to the DPLP proportion and size. This research provides valuable insights into the use of sustainable and renewable building materials, highlighting the benefits of exploiting agricultural waste in the constructional sector. The findings lay the groundwork for future research and innovation in environmentally friendly construction technologies.
- 4 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (7) , 3015
Open AccessExperimental Study on the Effect of Date Palm Powder on the Thermal and Physico-Mechanical Properties of Gypsum Mortars
Date palm leaves have been diachronically applied in building materials in the Middle East and North Africa (MENA) region, so as to enhance specific properties, such as volume stability and strength. This research work concerns an experimental study on the impact of date palm leaflet powder (DPLP) on the thermal and physico-mechanical properties of gypsum mortars. A series of mortar compositions were prepared with different proportions of DPLP (0, 1, 3, and 5% w/w of binder) and variant particle size (0.5, 1, and 1.5 mm). The results showed that the mortars containing DPLP exhibited significant changes in their properties due to variations in DPLP concentration and particle size. Increased DPLP led to lower density, higher porosity, and water absorption rate, whereas mechanical strength and thermal conductivity were decreased according to the DPLP proportion and size. This research provides valuable insights into the use of sustainable and renewable building materials, highlighting the benefits of exploiting agricultural waste in the constructional sector. The findings lay the groundwork for future research and innovation in environmentally friendly construction technologies.
- 12 October 2022
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 44 (4) , 9564-9583
Performance of earth-air heat exchanger in cooling, heating, and reducing carbon emissions of an industrial poultry farm: A case study
This paper aims to study an earth-air heat exchanger system proposed to cover the living environment needs and reduce energy consumption and greenhouse gas emissions of an industrial poultry house in southern Algeria. For this purpose, a detailed mathematical model was used to determine the thermal needs of this industrial building. The soil temperature was studied to estimate the appropriate depth for installing the earth-air heat exchanger, followed by a parametric and economic study to determine its dimensions and cost. Finally, compare its performance with the systems currently used in this industrial farm. The study results, which were obtained in extreme working conditions, showed that the earth air heat exchanger could cover 45% and 38% of the heating and cooling demands, respectively. In summer, the proposed heat exchanger was able to reduce the temperature from 47°C to 27.1°C, while in winter, it was able to increase the temperature from 4.8°C to 22.9°C, and its performance was stable compared to the systems currently used, and, it recorded temperatures better under hot outside conditions. Furthermore, its use reduces CO2 emissions to 719 kgCO2/day in heating and 2531 kgCO2/day in cooling, making it a suitable solution for this type of industrial building.
- 12 October 2022
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 44 (4) , 9564-9583
Performance of earth-air heat exchanger in cooling, heating, and reducing carbon emissions of an industrial poultry farm: A case study
This paper aims to study an earth-air heat exchanger system proposed to cover the living environment needs and reduce energy consumption and greenhouse gas emissions of an industrial poultry house in southern Algeria. For this purpose, a detailed mathematical model was used to determine the thermal needs of this industrial building. The soil temperature was studied to estimate the appropriate depth for installing the earth-air heat exchanger, followed by a parametric and economic study to determine its dimensions and cost. Finally, compare its performance with the systems currently used in this industrial farm. The study results, which were obtained in extreme working conditions, showed that the earth air heat exchanger could cover 45% and 38% of the heating and cooling demands, respectively. In summer, the proposed heat exchanger was able to reduce the temperature from 47°C to 27.1°C, while in winter, it was able to increase the temperature from 4.8°C to 22.9°C, and its performance was stable compared to the systems currently used, and, it recorded temperatures better under hot outside conditions. Furthermore, its use reduces CO2 emissions to 719 kgCO2/day in heating and 2531 kgCO2/day in cooling, making it a suitable solution for this type of industrial building.
- 1 January 2022
- Published by Desalination Publications in Desalination and Water Treatment
- Vol. 279, 140-146
Efficiency improvement of air-cooled photovoltaic modules utilizing copper heat dissipators
- 1 January 2022
- Published by Desalination Publications in Desalination and Water Treatment
- Vol. 279, 140-146
Efficiency improvement of air-cooled photovoltaic modules utilizing copper heat dissipators