JLJune Sung Lim

June Sung Lim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


June Sung Lim has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Renewable Intermittency Redistributes Catalyst Recovery and Membrane Degradation in Anion Exchange Membrane Water Electrolysis

    by Anastasiia Voronova, Sol Kim, June Sung Lim, Jin Young Kim, Hee‐Young Park, Sang Hoon Joo, Jong Hyun Jang, Bora Seo

    Renewable intermittency is widely regarded as a durability stressor in water electrolysis, yet its impact on competing degradation and recovery processes within the cell remains unclear. Here, we show that realistic intermittent operation redistributes catalyst recovery and membrane degradation in anion exchange membrane water electrolysis (AEMWE). A Ni–Fe‐based AEMWE single‐cell was operated under high‐resolution, solar‐mimicking load profiles that reproduce day–night intermittency without external buffering. Electrochemical diagnostics reveal reversible changes in activation, Ohmic, and mass‐transport losses, indicating partial performance recovery during zero‐current intervals. In situ X‐ray absorption spectroscopy attributes this behavior to reversible oxidation‐state and coordination changes of Ni and Fe, associated with the reversible formation and relaxation of amorphous (oxy)hydroxide surface layers. In contrast, hydrogen crossover measurements reveal increased crossover under low‐current operation, while post‐mortem membrane analyses provide independent evidence of membrane deterioration, identifying a critical system‐level limitation. These results show that intermittency does not uniformly mitigate degradation but redistributes it across cell components, enabling catalyst self‐restoration while exacerbating membrane vulnerability. This work establishes intermittency as a double‐edged operational parameter and provides a framework for designing materials and operating strategies for durable, battery‐free AEM water electrolysis.

  • Designing Ni Single Atom Catalysts Mimicking the Ni SOD Enzyme for Efficient H2O2 Electrosynthesis

    by June Sung Lim, Jinjong Kim, Sang Hoon Joo

    Hydrogen peroxide (H2O2) is one of essential commodity chemicals that is extensively used in various applications such as pulp & paper bleaching, wastewater treatment, and chemical synthesis. The electrochemical H2O2 production via oxygen reduction (2e− ORR) has emerged a promising method of H2O2 production, as it allows clean, continuous, and on-site H2O2 production. We have extensively explored the preparative chemistry of Ni single atom catalysts (Ni SACs) for H2O2 electrosynthesis, inspired by an H2O2-producing metalloenzyme, nickel superoxide dismutase (Ni SOD) with cofactor structures, which consists of a distorted square planar Ni2+ site, phenol group in tyrosine, and amine group in cysteine. We found that the formation of distorted square planar Ni2+–N x sites with an appropriate degree of distortion is crucial for boosting H2O2 electrosynthesis activity. The optimized Ni SAC exhibited the best H2O2 electrosynthesis mass activity among the reported non-precious metal SACs and carbon-based catalysts. By subjecting the optimized Ni SAC to post-synthetic heat treatments, different types of heteroatom functionality were formed with almost similar Ni2+–N x coordination structure. The catalyst possessing edge amine and phenol groups with distorted square planar Ni2+–N x sites exhibited further enhanced catalytic activity. The Ni TOF calculation revealed a synergistic effect between the Ni2+–N x sites and heteroatom groups.

  • Open Access

    Dinuclear titanium on TS-1 for propylene epoxidation at alkaline condition

    by Ja Hun Kwak, Kwang Hyun Kim, Taehyeon Kim, Haneul Kim, June Sung Lim, Myohwa Ko, Wonjoo Jin, Kwanyong Seo, Sang Hoon Joo, Sung June Cho, et al.

    Propylene epoxidation is an important industrial process, but current techniques have shown adverse environmental impacts.1-3 Recently, the eco-friendly photo-electro-heterogeneous catalytic production of propylene oxide (PO) has been reported using in situ generated H2O2 and a zeolite catalyst (titanium silicalite-1, TS-1).4 However, the PO production rate was too low due to the low solar H2O2 production rate. In this work, we recorded high solar H2O2 production rate required for the practical PO production for first time. However, TS-1 exhibits low activity in the presence of alkali metal ions under alkaline condition, which are crucial for efficient solar H2O2 production. Herein, we hydrothermally synthesize a TS-1 catalyst containing dinuclear titanium sites and Ti–O–Ti bonds and show that it efficiently promotes propylene epoxidation under alkaline conditions (pH 11). The results of density functional theory (DFT) calculations and instrumental analyses reveal that the dinuclear titanium sites are active for propylene epoxidation and synergistically interact with alkali metals ions to prevent hydrolysis of PO to propylene glycol. Thus, our work demonstrates the superiority of the developed catalytic system over its predecessors, paving the way for the use of TS-1 in other partial oxidation reactions and the development of novel environmentally benign chemical processes.

  • Open Access

    3D microprinting of inorganic porous materials by chemical linking-induced solidification of nanocrystals

    by Minju Song, Yoonkyum Kim, Du San Baek, Ho Young Kim, Da Hwi Gu, Haiyang Li, Benjamin V. Cunning, Seong Eun Yang, Seung Hwae Heo, Seunghyun Lee, et al.

    Three-dimensional (3D) microprinting is considered a next-generation manufacturing process for the production of microscale components; however, the narrow range of suitable materials, which include mainly polymers, is a critical issue that limits the application of this process to functional inorganic materials. Herein, we develop a generalised microscale 3D printing method for the production of purely inorganic nanocrystal-based porous materials. Our process is designed to solidify all-inorganic nanocrystals via immediate dispersibility control and surface linking-induced interconnection in the nonsolvent linker bath and thereby creates multibranched gel networks. The process works with various inorganic materials, including metals, semiconductors, magnets, oxides, and multi-materials, not requiring organic binders or stereolithographic equipment. Filaments with a diameter of sub-10 μm are printed into designed complex 3D microarchitectures, which exhibit full nanocrystal functionality and high specific surface areas as well as hierarchical porous structures. This approach provides the platform technology for designing functional inorganics-based porous materials.