Chengru Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chengru Zhu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Shao-Fei Wang
Xi’an Jiaotong University
4 shared publications - Wenyue Tang
Xi’an Jiaotong University
3 shared publications - Yan-Zhao Xie
Xi’an Jiaotong University
3 shared publications Dun Qian
1 shared publication- Kai Lu
Xi’an Jiaotong University
1 shared publication Mingquan Zeng
1 shared publication
Latest Publications
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- p. 1
Determination of the Weighted Phase Center for UWB Antennas of an Impulse Radar for the Detection of External Insulation Defects to Improve Imaging Focusing Effect
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- p. 1
Determination of the Weighted Phase Center for UWB Antennas of an Impulse Radar for the Detection of External Insulation Defects to Improve Imaging Focusing Effect
- 14 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 39 (4) , 2295-2305
A Novel Method for the Detection of External Insulation Defects Based on the Ultrawideband Impulse Radar Technology
In this paper, a novel method for the detection of external insulation defects based on the ultrawideband impulse radar is proposed. The circular synthetic aperture radar method was adopted to collect reflected signals in this paper, since the detected object often has a symmetric shape (e.g., insulators, bushings, etc.). The mean suppression method is adopted to filter out the clutters of reflected waveforms from different directions, and thus the reflected signals of defects can be amplified. Then, the defect images are extracted from the processed reflected signals with the back projection algorithm. Moreover, since the example objects studied here are of multi-layer circular structure with different dielectrics for each layer, the accurate wave-propagation time should be calibrated before the calculation of back projection amplitudes. Thus, the multi-layer model is established to figure out the refraction path, while the propagation time is compensated based on the wave speeds of different dielectrics. The non-destructive detection capacity of the proposed UWB detection method is verified by the simulation first, and then the practical detection effectiveness is verified by the comparison experiment of an intact insulator and a defective one. The experimental results indicate that the measured length of the internal crack as an extension of the observed surface cavity is about 30 mm, and the severest defect point is only 4.2 mm away from the latter, which means the defect locating is of high accuracy. The investigation results demonstrate that, due to the good penetrability and imaging resolution, the impulse radar exhibits good potential in the online detection of both surface and internal defects of the external insulation equipment.
- 14 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Delivery
- Vol. 39 (4) , 2295-2305
A Novel Method for the Detection of External Insulation Defects Based on the Ultrawideband Impulse Radar Technology
In this paper, a novel method for the detection of external insulation defects based on the ultrawideband impulse radar is proposed. The circular synthetic aperture radar method was adopted to collect reflected signals in this paper, since the detected object often has a symmetric shape (e.g., insulators, bushings, etc.). The mean suppression method is adopted to filter out the clutters of reflected waveforms from different directions, and thus the reflected signals of defects can be amplified. Then, the defect images are extracted from the processed reflected signals with the back projection algorithm. Moreover, since the example objects studied here are of multi-layer circular structure with different dielectrics for each layer, the accurate wave-propagation time should be calibrated before the calculation of back projection amplitudes. Thus, the multi-layer model is established to figure out the refraction path, while the propagation time is compensated based on the wave speeds of different dielectrics. The non-destructive detection capacity of the proposed UWB detection method is verified by the simulation first, and then the practical detection effectiveness is verified by the comparison experiment of an intact insulator and a defective one. The experimental results indicate that the measured length of the internal crack as an extension of the observed surface cavity is about 30 mm, and the severest defect point is only 4.2 mm away from the latter, which means the defect locating is of high accuracy. The investigation results demonstrate that, due to the good penetrability and imaging resolution, the impulse radar exhibits good potential in the online detection of both surface and internal defects of the external insulation equipment.
- Open Access
- 1 December 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (12)
Tightly coupled arrays with time-domain beam scan for the radiation of high-power ultrawideband electromagnetic pulses
In this paper, a kind of tightly coupled array (TCA) with time-domain beam scan is developed for the radiation of high-power ultrawideband (UWB) electromagnetic pulses, and the peak-power pattern is proposed to characterize the directivity. First, the active voltage standing wave ratio (AVSWR) bandwidth of the TCA is optimized, which is the precondition for the beam scan. It indicates that the lower-cutoff frequency (LCF) is inversely proportional to the total length of the whole array; an increase in the distance between the array and the ground plane could remarkably reduce the LCF; and an increase in the element number can also decrease the LCF because of the increase in length, but more elements would make the center elements difficult to match in the low-frequency range, so there is a limitation on the number of elements for a certain LCF. Based on these results, a six-element linear array is designed. Then, the definition of the peak-power pattern is proposed to characterize the directivity of the UWB pulsed antenna. Finally, the optimized six-element array is developed, and the measured working band is 276 MHz–6.4 GHz (AVSWR < 3). The effective potential gain is 1.76, and it improves by 51.7% with a reduction in the aperture area by 68.4% compared with the previous TCA, which means that the aperture efficiency is remarkably improved. The half-power beam width of the developed TCA with the scan angle of 0° is 45°. The time-domain beam scan could be performed with time-delay feeding lines, and the maximum scan angle is over ±30° in the E-plane. The developed TCA can be applied for the generation of high-power electromagnetic environments for the study of intentional electromagnetic interference.
- 1 December 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (12)
Open AccessTightly coupled arrays with time-domain beam scan for the radiation of high-power ultrawideband electromagnetic pulses
In this paper, a kind of tightly coupled array (TCA) with time-domain beam scan is developed for the radiation of high-power ultrawideband (UWB) electromagnetic pulses, and the peak-power pattern is proposed to characterize the directivity. First, the active voltage standing wave ratio (AVSWR) bandwidth of the TCA is optimized, which is the precondition for the beam scan. It indicates that the lower-cutoff frequency (LCF) is inversely proportional to the total length of the whole array; an increase in the distance between the array and the ground plane could remarkably reduce the LCF; and an increase in the element number can also decrease the LCF because of the increase in length, but more elements would make the center elements difficult to match in the low-frequency range, so there is a limitation on the number of elements for a certain LCF. Based on these results, a six-element linear array is designed. Then, the definition of the peak-power pattern is proposed to characterize the directivity of the UWB pulsed antenna. Finally, the optimized six-element array is developed, and the measured working band is 276 MHz–6.4 GHz (AVSWR < 3). The effective potential gain is 1.76, and it improves by 51.7% with a reduction in the aperture area by 68.4% compared with the previous TCA, which means that the aperture efficiency is remarkably improved. The half-power beam width of the developed TCA with the scan angle of 0° is 45°. The time-domain beam scan could be performed with time-delay feeding lines, and the maximum scan angle is over ±30° in the E-plane. The developed TCA can be applied for the generation of high-power electromagnetic environments for the study of intentional electromagnetic interference.