Zeheng Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zeheng Zhang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ruikun Mai
Tongji University
5 shared publications - Yang Chen
School of Electrical Engineering Southwest Jiaotong University Chengdu China
4 shared publications - Zhengyou He
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
4 shared publications - Bin Yang
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
3 shared publications Zheng Li
Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Southwest Jiaotong University, Chengdu, China
2 shared publications- Binshan Zhang
Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Chengdu, China
1 shared publication
Latest Publications
- 30 July 2025
- Published by Springer Nature in Electrical Engineering
- Vol. 107 (11) , 14483-14500
Modeling and performance assessment of IPT systems for powering sensors in metallic enclosures
- 30 July 2025
- Published by Springer Nature in Electrical Engineering
- Vol. 107 (11) , 14483-14500
Modeling and performance assessment of IPT systems for powering sensors in metallic enclosures
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 15414-15419
Wireless Sensor Power Supply for Rotating Shaft Using DC-Side Diode Array With Stable Output
24 × 7 health monitoring of rotating shaft is very important for the safe operation of automotive axles. Wireless sensor power supply technology is one of the promising power supply means for monitoring systems. Since the radius of many rotation shafts is large up to 1 m, segmented coils are adopted to reduce the magnetic interference and power loss compared to single receiver coils, but this will lead to output voltage fluctuation causing the monitoring system failures. This letter proposes a fluctuation suppression method by a dc-side diode array and parameter optimization. Using multiple reverse parallel diode groups to connect the dc side of multiple receivers and the load, the diodes will be conducted when corresponding coils are activated, while those without induced voltage will not be conducted. In this way, the mutual inductance fluctuation as per different rotation angles can be greatly reduced. In addition, a detuned system has been designed, rendering the output gain insensitive to variations in mutual inductance, thereby enhancing the output stability. A prototype was built to verify the theoretical analysis. The experimental results indicate that the output voltage fluctuation is only 5.0%. The proposed method can achieve significant output stability without complex control and dedicated coil design.
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 15414-15419
Wireless Sensor Power Supply for Rotating Shaft Using DC-Side Diode Array With Stable Output
24 × 7 health monitoring of rotating shaft is very important for the safe operation of automotive axles. Wireless sensor power supply technology is one of the promising power supply means for monitoring systems. Since the radius of many rotation shafts is large up to 1 m, segmented coils are adopted to reduce the magnetic interference and power loss compared to single receiver coils, but this will lead to output voltage fluctuation causing the monitoring system failures. This letter proposes a fluctuation suppression method by a dc-side diode array and parameter optimization. Using multiple reverse parallel diode groups to connect the dc side of multiple receivers and the load, the diodes will be conducted when corresponding coils are activated, while those without induced voltage will not be conducted. In this way, the mutual inductance fluctuation as per different rotation angles can be greatly reduced. In addition, a detuned system has been designed, rendering the output gain insensitive to variations in mutual inductance, thereby enhancing the output stability. A prototype was built to verify the theoretical analysis. The experimental results indicate that the output voltage fluctuation is only 5.0%. The proposed method can achieve significant output stability without complex control and dedicated coil design.
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 23-27
A Dynamic Wireless Power Transfer System Using DC-Controlled Variable Inductor for Segment Transmitter Automatic Switching
Segmented transmitter coils are commonly employed in dynamic wireless power transfer, and automatic switching is a preferred function to limit the transmitter current. This letter proposes a method for segment transmitter automatic switching utilizing a dc-controlled variable inductor (DCCVI), where the dc current can change the ac side's self-inductance. When the coils are decoupled, the dc current is small, so the inductance of the DCCVI is relatively large, leading to the suppression of the transmitter current. When the coils meet certain coupling conditions, the dc current becomes large, leading to a significant reduction in the ac inductance of the DCCVI, resulting in higher transmission power, thereby enabling segment transmitter automatic switching. The proposed method is straightforward and does not need additional position feedback. The experimental results demonstrate that the proposed system can automatically limit the coil current within the range of [0, 0.15] and achieve higher power transmission with higher efficiency within the coupling range of [0.165, 0.3].
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 23-27
A Dynamic Wireless Power Transfer System Using DC-Controlled Variable Inductor for Segment Transmitter Automatic Switching
Segmented transmitter coils are commonly employed in dynamic wireless power transfer, and automatic switching is a preferred function to limit the transmitter current. This letter proposes a method for segment transmitter automatic switching utilizing a dc-controlled variable inductor (DCCVI), where the dc current can change the ac side's self-inductance. When the coils are decoupled, the dc current is small, so the inductance of the DCCVI is relatively large, leading to the suppression of the transmitter current. When the coils meet certain coupling conditions, the dc current becomes large, leading to a significant reduction in the ac inductance of the DCCVI, resulting in higher transmission power, thereby enabling segment transmitter automatic switching. The proposed method is straightforward and does not need additional position feedback. The experimental results demonstrate that the proposed system can automatically limit the coil current within the range of [0, 0.15] and achieve higher power transmission with higher efficiency within the coupling range of [0.165, 0.3].
- 9 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (2) , 1942-1946
A Clamp Circuit-Based Inductive Power Transfer System With Reconfigurable Rectifier Tolerating Extensive Coupling Variations
Coupling variation tolerance is one of the most crucial abilities of the inductive power transfer (IPT) system because the variable coupling can dramatically degrade the output power. This letter proposes a clamp circuit-based IPT system with a reconfigurable rectifier featuring high antimisalignment. The clamp circuit can adaptively switch from one stable operating region to the other according to the coupling coefficients. The reconfigurable rectifier can work in half-bridge mode or full-bridge mode, which can build another two adaptively switching stable operating regions such that the proposed IPT system can provide nearly stable output power resisting extensive coupling variations. A 400-W prototype was built to verify the theoretical analysis. The experimental results indicate that the output power fluctuation of the proposed method is only 5.98% when the coupling coefficient varies from 0.1 to 0.4 (400%), and the system efficiency is from 86.1% to 94.3%. The proposed method does not need complicated control or dedicated coil design, and it can implement significant antimisalignment improvement.
- 9 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (2) , 1942-1946
A Clamp Circuit-Based Inductive Power Transfer System With Reconfigurable Rectifier Tolerating Extensive Coupling Variations
Coupling variation tolerance is one of the most crucial abilities of the inductive power transfer (IPT) system because the variable coupling can dramatically degrade the output power. This letter proposes a clamp circuit-based IPT system with a reconfigurable rectifier featuring high antimisalignment. The clamp circuit can adaptively switch from one stable operating region to the other according to the coupling coefficients. The reconfigurable rectifier can work in half-bridge mode or full-bridge mode, which can build another two adaptively switching stable operating regions such that the proposed IPT system can provide nearly stable output power resisting extensive coupling variations. A 400-W prototype was built to verify the theoretical analysis. The experimental results indicate that the output power fluctuation of the proposed method is only 5.98% when the coupling coefficient varies from 0.1 to 0.4 (400%), and the system efficiency is from 86.1% to 94.3%. The proposed method does not need complicated control or dedicated coil design, and it can implement significant antimisalignment improvement.
- 11 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 9 (3) , 3836-3848
A Detuned S-S Compensated IPT System With Two Discrete Frequencies for Maintaining Stable Power Transfer Versus Wide Coupling Variation
Stable power transmission is one of the key factors in the inductive power transfer (IPT) system. However, misalignment between the primary and secondary sides is almost inevitable in practice, affecting the system performance due to the coupling variation. With the widespread use of IPT technology, it is desired to transfer power from the primary side to the secondary side with a wide misalignment range as large as possible. To address this issue, the design method of the detuned circuit is widely applied in the IPT system. This paper analyzes the characteristics of the transfer power of the detuned series–series (S-S) topology with frequency variations and proposes a maintaining stable power transfer method versus wide coupling variation by adopting two discrete frequencies. Further, a design step is given to obtain the system parameters. Theoretical and experimental results are provided to demonstrate the misalignment performance of the proposed method. The results show that the coupling range is extended from [0.115-0.2] to [0.115-0.27] with the 5.6% fluctuation of the output power, and the corresponding efficiency varies from 91.46% to 95.52%.
- 11 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 9 (3) , 3836-3848
A Detuned S-S Compensated IPT System With Two Discrete Frequencies for Maintaining Stable Power Transfer Versus Wide Coupling Variation
Stable power transmission is one of the key factors in the inductive power transfer (IPT) system. However, misalignment between the primary and secondary sides is almost inevitable in practice, affecting the system performance due to the coupling variation. With the widespread use of IPT technology, it is desired to transfer power from the primary side to the secondary side with a wide misalignment range as large as possible. To address this issue, the design method of the detuned circuit is widely applied in the IPT system. This paper analyzes the characteristics of the transfer power of the detuned series–series (S-S) topology with frequency variations and proposes a maintaining stable power transfer method versus wide coupling variation by adopting two discrete frequencies. Further, a design step is given to obtain the system parameters. Theoretical and experimental results are provided to demonstrate the misalignment performance of the proposed method. The results show that the coupling range is extended from [0.115-0.2] to [0.115-0.27] with the 5.6% fluctuation of the output power, and the corresponding efficiency varies from 91.46% to 95.52%.
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 161-164
The present and future of electric vehicles : Market analysis and forecast of different types of electric vehicles
With the increasingly serious energy crisis and environmental problems, people's demand for new energy is more urgent, so new energy products emerge in an endless stream. New energy vehicles are highly praised by most countries for their energy saving and environmental protection, and there are many kinds of new energy vehicles.This paper first introduces several common new energy vehicles in the market. Then, this paper obtains the output data of three kinds of new energy vehicles, and makes a correlation analysis by using gray correlation, and concludes that the correlation between the total output of plug-in hybrid vehicles and vehicles is strong, which is the representative of today's new energy vehicles. This paper also uses time series to predict the electric vehicles in the next two years, and obtains a reasonable prediction model. Moreover, this paper creatively puts forward the impact of technological innovation on new energy vehicles, and uses a reasonable model to predict the changes of the output and total output of fuel cell vehicles after technological innovation. Finally, this paper tests the time series and further proves the rationality of the prediction.
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 161-164
The present and future of electric vehicles : Market analysis and forecast of different types of electric vehicles
With the increasingly serious energy crisis and environmental problems, people's demand for new energy is more urgent, so new energy products emerge in an endless stream. New energy vehicles are highly praised by most countries for their energy saving and environmental protection, and there are many kinds of new energy vehicles.This paper first introduces several common new energy vehicles in the market. Then, this paper obtains the output data of three kinds of new energy vehicles, and makes a correlation analysis by using gray correlation, and concludes that the correlation between the total output of plug-in hybrid vehicles and vehicles is strong, which is the representative of today's new energy vehicles. This paper also uses time series to predict the electric vehicles in the next two years, and obtains a reasonable prediction model. Moreover, this paper creatively puts forward the impact of technological innovation on new energy vehicles, and uses a reasonable model to predict the changes of the output and total output of fuel cell vehicles after technological innovation. Finally, this paper tests the time series and further proves the rationality of the prediction.