Lixin Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lixin Zhang has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Yongqian Li
Department of Electronic and Communication Engineering, North China Electric Power University, Baoding 071003, China
6 shared publications - Zijuan Liu
Department of Electronic and Communication Engineering, North China Electric Power University, Baoding 071003, China
4 shared publications Yongqian Li
North China Elect Power Univ, Dept Elect & Commun Engn, Baoding 071003, Peoples R China
3 shared publicationsHaijun Fan
China United Network Commun Corp Ltd, Hebei Branch, Shijiazhuang 050000, Peoples R China
1 shared publication- Haijun Fan
Department of Electronic and Communication Engineering, North China Electric Power University, Baoding 071003, China
1 shared publication Han-Bai Fan
North China Electric Power University
1 shared publication
Latest Publications
- Open Access
- 20 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11543
An FMF-MMF Composite Fiber Structure for Enhanced Bend Tolerance in Single-Ended BOTDA Systems
To address the issues of signal attenuation and reduced stability in Brillouin frequency shift (BFS) demodulation in single-ended Brillouin optical time-domain analysis (BOTDA) sensors under small-radius bending conditions, a distributed temperature sensing scheme based on a composite structure formed by fusion-splicing few-mode fiber (FMF) and multimode fiber (MMF) is proposed. The normalized power distribution along the fiber, Brillouin gain spectrum (BGS), and BFS were measured at various bending radii; additionally, the demodulability of the spectral lines under bending conditions was evaluated using the Brillouin phase-shift spectrum (BPS). Experimental results demonstrate that reliable BFS extraction and stable BPS fitting are maintained when the bending radius mm, whereas the quality of spectral line fitting degrades significantly when mm. With a bending radius of mm, distributed temperature measurement was achieved over the range of 25–65 C, yielding a temperature sensitivity of approximately 1.03 MHz/C and a spatial resolution of approximately 5.15 m. These results indicate that the FMF-MMF composite structure enables single-ended BOTDA systems to maintain signal transmission and distributed temperature sensing capabilities even under small-radius bending conditions.- 20 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11543
Open AccessAn FMF-MMF Composite Fiber Structure for Enhanced Bend Tolerance in Single-Ended BOTDA Systems
To address the issues of signal attenuation and reduced stability in Brillouin frequency shift (BFS) demodulation in single-ended Brillouin optical time-domain analysis (BOTDA) sensors under small-radius bending conditions, a distributed temperature sensing scheme based on a composite structure formed by fusion-splicing few-mode fiber (FMF) and multimode fiber (MMF) is proposed. The normalized power distribution along the fiber, Brillouin gain spectrum (BGS), and BFS were measured at various bending radii; additionally, the demodulability of the spectral lines under bending conditions was evaluated using the Brillouin phase-shift spectrum (BPS). Experimental results demonstrate that reliable BFS extraction and stable BPS fitting are maintained when the bending radius mm, whereas the quality of spectral line fitting degrades significantly when mm. With a bending radius of mm, distributed temperature measurement was achieved over the range of 25–65 C, yielding a temperature sensitivity of approximately 1.03 MHz/C and a spatial resolution of approximately 5.15 m. These results indicate that the FMF-MMF composite structure enables single-ended BOTDA systems to maintain signal transmission and distributed temperature sensing capabilities even under small-radius bending conditions. - Open Access
Research on Distributed Temperature and Bending Sensing Measurement Based on DPP-BOTDA
Traditional single-mode Brillouin optical time-domain analysis systems are inherently limited in terms of sensing capacity, susceptibility to bending loss, and spatial resolution. Multi-core fibers present a promising approach to overcoming these limitations. In this study, a seven-core fiber was utilized, with the central core and three asymmetrically positioned off-axis cores selected for sensing. The temperature coefficients of the four selected cores were experimentally calibrated as 1.103, 0.962, 1.277, and 0.937 MHz/°C, respectively. By employing differential pulse techniques within the Brillouin distributed sensing system, temperature-compensated bending measurements were achieved with a spatial resolution of 20 cm. The fiber was wound around cylindrical mandrels with diameters of 7 cm, 10 cm, and 15 cm. Experimental results demonstrate effective decoupling of temperature and bending strain, enabling accurate curvature reconstruction. Error analysis reveals a minimum deviation of 0.04% for smaller diameters and 0.68% for larger diameters. Cross-comparison of measurements conducted at varying temperatures confirms the robustness and effectiveness of the proposed temperature compensation method.
Open AccessResearch on Distributed Temperature and Bending Sensing Measurement Based on DPP-BOTDA
Traditional single-mode Brillouin optical time-domain analysis systems are inherently limited in terms of sensing capacity, susceptibility to bending loss, and spatial resolution. Multi-core fibers present a promising approach to overcoming these limitations. In this study, a seven-core fiber was utilized, with the central core and three asymmetrically positioned off-axis cores selected for sensing. The temperature coefficients of the four selected cores were experimentally calibrated as 1.103, 0.962, 1.277, and 0.937 MHz/°C, respectively. By employing differential pulse techniques within the Brillouin distributed sensing system, temperature-compensated bending measurements were achieved with a spatial resolution of 20 cm. The fiber was wound around cylindrical mandrels with diameters of 7 cm, 10 cm, and 15 cm. Experimental results demonstrate effective decoupling of temperature and bending strain, enabling accurate curvature reconstruction. Error analysis reveals a minimum deviation of 0.04% for smaller diameters and 0.68% for larger diameters. Cross-comparison of measurements conducted at varying temperatures confirms the robustness and effectiveness of the proposed temperature compensation method.
- 11 December 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (1) , 015519
Simultaneous temperature and strain sensing using few-mode fiber in a single-ended BOTDA system
Few-mode fibers contain a limited number of orthogonal modes, and the Brillouin frequency shift of different modes has different sensitivities to temperature and strain, which provides the possibility of realizing multi-parameter sensing. This paper proposes a novel single-ended Brillouin optical time domain analysis (BOTDA) sensing system that uses Rayleigh backscattered light in the fiber as the probe light, and uses a four-mode graded-index few-mode fiber (4GI-FMF) and a photonic lantern to realize two-parameter sensing. The mechanism of single-ended BOTDA based on FMF is investigated, the modes of 4GI-FMF and the principle of two-parameter measurement are analyzed, and an experimental setup utilizing single-ended BOTDA system with 4GI-FMF is constructed. The performance of the sensing system is analyzed by characterizing and evaluating the Brillouin scattering spectral of different modes and the sensitivity of Brillouin frequency shift to temperature and strain. The proposed sensing system realized reliable temperature and strain discrimination on a 1 km long 4GI-FMF, with temperature and strain accuracies of 1.9 °C and 43.7 με, respectively.
- 11 December 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (1) , 015519
Simultaneous temperature and strain sensing using few-mode fiber in a single-ended BOTDA system
Few-mode fibers contain a limited number of orthogonal modes, and the Brillouin frequency shift of different modes has different sensitivities to temperature and strain, which provides the possibility of realizing multi-parameter sensing. This paper proposes a novel single-ended Brillouin optical time domain analysis (BOTDA) sensing system that uses Rayleigh backscattered light in the fiber as the probe light, and uses a four-mode graded-index few-mode fiber (4GI-FMF) and a photonic lantern to realize two-parameter sensing. The mechanism of single-ended BOTDA based on FMF is investigated, the modes of 4GI-FMF and the principle of two-parameter measurement are analyzed, and an experimental setup utilizing single-ended BOTDA system with 4GI-FMF is constructed. The performance of the sensing system is analyzed by characterizing and evaluating the Brillouin scattering spectral of different modes and the sensitivity of Brillouin frequency shift to temperature and strain. The proposed sensing system realized reliable temperature and strain discrimination on a 1 km long 4GI-FMF, with temperature and strain accuracies of 1.9 °C and 43.7 με, respectively.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-8
Distributed Measurement Based on Sparse Spectra of Brillouin Optical Fiber Sensors in IoT
Distributed temperature/strain measurement utilizing Brillouin optical fiber sensors in Internet-of-Things (IoT) has attracted more attention to achieve state monitoring of large-scale structure. However, the huge amount of measurement data increases the hardware burden and limits the measurement speed. To address this problem, distributed measurement based on sparse spectra of Brillouin optical fiber sensors in IoT is proposed in this paper. Non-locally centralized sparse representation (NCSR) and fast iterative shrinkage thresholding (FIST) algorithms are adopted to sparsely represent and reconstruct the measured Brillouin scattering spectra (BSS), respectively. Compared with other sparse representation and reconstruction algorithms, the performance of NCSR and FIST for signal-to-noise ratio (SNR) enhancement and successful recovery is the best. Only 25% of samples is needed to reconstruct BSS for further extraction of Brillouin frequency shift (BFS) and temperature. The consistence of BFSs obtained from original and reconstructed BSS both in simulation and experimental results indicates that the extracted BFSs and temperatures are reliable and accurately by applying sparse BSS obtained by NCSR and FIST. Different frequency scanning intervals and heating temperatures in the experiment are also considered for analysis and discussion. The proposed method has been demonstrated to be effective to decrease the quantity of data for acquisition, storage and further analysis, which is conducive to reduce the system cost and improve the SNR to achieve distributed measurement in IoT.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-8
Distributed Measurement Based on Sparse Spectra of Brillouin Optical Fiber Sensors in IoT
Distributed temperature/strain measurement utilizing Brillouin optical fiber sensors in Internet-of-Things (IoT) has attracted more attention to achieve state monitoring of large-scale structure. However, the huge amount of measurement data increases the hardware burden and limits the measurement speed. To address this problem, distributed measurement based on sparse spectra of Brillouin optical fiber sensors in IoT is proposed in this paper. Non-locally centralized sparse representation (NCSR) and fast iterative shrinkage thresholding (FIST) algorithms are adopted to sparsely represent and reconstruct the measured Brillouin scattering spectra (BSS), respectively. Compared with other sparse representation and reconstruction algorithms, the performance of NCSR and FIST for signal-to-noise ratio (SNR) enhancement and successful recovery is the best. Only 25% of samples is needed to reconstruct BSS for further extraction of Brillouin frequency shift (BFS) and temperature. The consistence of BFSs obtained from original and reconstructed BSS both in simulation and experimental results indicates that the extracted BFSs and temperatures are reliable and accurately by applying sparse BSS obtained by NCSR and FIST. Different frequency scanning intervals and heating temperatures in the experiment are also considered for analysis and discussion. The proposed method has been demonstrated to be effective to decrease the quantity of data for acquisition, storage and further analysis, which is conducive to reduce the system cost and improve the SNR to achieve distributed measurement in IoT.
- Open Access
Research on Multi-Core Curvature Sensing Measurement Based on PPP-BOTDA
To address the issue of spatial resolution limitations in traditional Brillouin optical time-domain analysis systems due to phonon lifetime constraints, we employed pre-pumped pulse technology. Additionally, to mitigate the double-peak phenomenon observed in pre-pumped Brillouin optical time-domain analysis systems, we implemented a two-sided band interference method to reduce the linewidth of the double-peak fitting. We conducted bending measurements on three eccentric cores and intermediate cores spaced 120° apart. Our results demonstrate that the system described in this paper can achieve a spatial resolution of 30 cm, with bimodal linewidths of 23.1 MHz and 16.0 MHz. Using the parallel transmission frame algorithm, we determined the curvature of a seven-core fiber with a curvature diameter of approximately 10 cm to be 20.67 m−1, with an error margin of 3.2%.
Open AccessResearch on Multi-Core Curvature Sensing Measurement Based on PPP-BOTDA
To address the issue of spatial resolution limitations in traditional Brillouin optical time-domain analysis systems due to phonon lifetime constraints, we employed pre-pumped pulse technology. Additionally, to mitigate the double-peak phenomenon observed in pre-pumped Brillouin optical time-domain analysis systems, we implemented a two-sided band interference method to reduce the linewidth of the double-peak fitting. We conducted bending measurements on three eccentric cores and intermediate cores spaced 120° apart. Our results demonstrate that the system described in this paper can achieve a spatial resolution of 30 cm, with bimodal linewidths of 23.1 MHz and 16.0 MHz. Using the parallel transmission frame algorithm, we determined the curvature of a seven-core fiber with a curvature diameter of approximately 10 cm to be 20.67 m−1, with an error margin of 3.2%.
- Open Access
Performance Enhancement in a Few-Mode Rayleigh-Brillouin Optical Time Domain Analysis System Using Pulse Coding and LMD Algorithm
Rayleigh Brillouin optical time domain analysis (BOTDA) uses the backscattered Rayleigh light generated in the fiber as the probe light, which has a lower detection light intensity compared to the BOTDA technique. As a result, its temperature-sensing technology suffers from a low signal-to-noise ratio (SNR) and severe sensing unreliability due to the influence of the low probe signal and high noise level. The pulse coding and LMD denoising method are applied to enhance the performance of the Brillouin frequency shift detection and temperature measurement. In this study, the mechanism of Rayleigh BOTDA based on a few-mode fiber (FMF) is investigated, the principles of the Golay code and local mean decomposition (LMD) algorithm are analyzed, and the experimental setup of the Rayleigh BOTDA system using an FMF is constructed to analyze the performance of the sensing system. Compared with a single pulse of 50 ns, the 32-bit Golay coding with a pulse width of 10 ns improves the spatial resolution to 1 m. Further enhanced by the LMD algorithm, the SNR and temperature measurement accuracy are increased by 5.5 dB and 1.05 °C, respectively. Finally, a spatial resolution of 1.12 m and a temperature measurement accuracy of 2.85 °C are achieved using a two-mode fiber with a length of 1 km.
Open AccessPerformance Enhancement in a Few-Mode Rayleigh-Brillouin Optical Time Domain Analysis System Using Pulse Coding and LMD Algorithm
Rayleigh Brillouin optical time domain analysis (BOTDA) uses the backscattered Rayleigh light generated in the fiber as the probe light, which has a lower detection light intensity compared to the BOTDA technique. As a result, its temperature-sensing technology suffers from a low signal-to-noise ratio (SNR) and severe sensing unreliability due to the influence of the low probe signal and high noise level. The pulse coding and LMD denoising method are applied to enhance the performance of the Brillouin frequency shift detection and temperature measurement. In this study, the mechanism of Rayleigh BOTDA based on a few-mode fiber (FMF) is investigated, the principles of the Golay code and local mean decomposition (LMD) algorithm are analyzed, and the experimental setup of the Rayleigh BOTDA system using an FMF is constructed to analyze the performance of the sensing system. Compared with a single pulse of 50 ns, the 32-bit Golay coding with a pulse width of 10 ns improves the spatial resolution to 1 m. Further enhanced by the LMD algorithm, the SNR and temperature measurement accuracy are increased by 5.5 dB and 1.05 °C, respectively. Finally, a spatial resolution of 1.12 m and a temperature measurement accuracy of 2.85 °C are achieved using a two-mode fiber with a length of 1 km.
- Open Access
Single-Mode Input Fiber Combined with Multimode Sensing Fiber Used in Brillouin Optical Time-Domain Reflectometry
Conventional single-mode fiber (SMF) Brillouin optical time-domain reflectometry (BOTDR) suffers from a low signal-to-noise ratio (SNR) and severe sensing reliability due to the influence of the stimulated Brillouin scattering threshold and bend loss. In this study, a simple and low-cost distributed sensing structure, with a single-mode input fiber alignment fusion and a 50 μm diameter graded index multimode sensing fiber, is designed, and the SNR characteristic is investigated. Through theoretical derivation and experimental verification, a higher SNR and excellent bending resistance are realized in BOTDR. The experimentally measured improvements in the SNR of the proposed sensing structure over the SMF at the beginning and end of a 5 km fiber are 2.5 dB and 1.3 dB, respectively. The minimum bending radius of the sensing structure is 2.25 mm, which is much better than that of the SMFs. The bidirectional optical losses between the SMF and the 50 μm graded index multimode fiber are measured by a simple experiment system and are 0.106 dB and 1.35 dB, respectively. The temperature-sensing characteristics of the sensing structure are measured by the self-built frequency-shift local heterodyne BOTDR sensor, and the measured temperature sensitivity and accuracy are 0.946 MHz/℃ and 1 ℃, respectively. The design provides a reference for BOTDR with a high SNR and has great potential for structural safety and health monitoring of infrastructures.
Open AccessSingle-Mode Input Fiber Combined with Multimode Sensing Fiber Used in Brillouin Optical Time-Domain Reflectometry
Conventional single-mode fiber (SMF) Brillouin optical time-domain reflectometry (BOTDR) suffers from a low signal-to-noise ratio (SNR) and severe sensing reliability due to the influence of the stimulated Brillouin scattering threshold and bend loss. In this study, a simple and low-cost distributed sensing structure, with a single-mode input fiber alignment fusion and a 50 μm diameter graded index multimode sensing fiber, is designed, and the SNR characteristic is investigated. Through theoretical derivation and experimental verification, a higher SNR and excellent bending resistance are realized in BOTDR. The experimentally measured improvements in the SNR of the proposed sensing structure over the SMF at the beginning and end of a 5 km fiber are 2.5 dB and 1.3 dB, respectively. The minimum bending radius of the sensing structure is 2.25 mm, which is much better than that of the SMFs. The bidirectional optical losses between the SMF and the 50 μm graded index multimode fiber are measured by a simple experiment system and are 0.106 dB and 1.35 dB, respectively. The temperature-sensing characteristics of the sensing structure are measured by the self-built frequency-shift local heterodyne BOTDR sensor, and the measured temperature sensitivity and accuracy are 0.946 MHz/℃ and 1 ℃, respectively. The design provides a reference for BOTDR with a high SNR and has great potential for structural safety and health monitoring of infrastructures.
- 28 March 2022
- Published by Springer Nature in Optoelectronics Letters
- Vol. 18 (3) , 170-174
Performance improvement method of single-ended BOTDA system based on Fresnel reflection
- 28 March 2022
- Published by Springer Nature in Optoelectronics Letters
- Vol. 18 (3) , 170-174
Performance improvement method of single-ended BOTDA system based on Fresnel reflection
- 1 November 2018
- Published by Elsevier in Optics Communications
- Vol. 427, 190-195
A self-heterodyne detection Rayleigh Brillouin optical time domain analysis system
- 1 November 2018
- Published by Elsevier in Optics Communications
- Vol. 427, 190-195
A self-heterodyne detection Rayleigh Brillouin optical time domain analysis system