TZTeng Zhang

Teng Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Teng Zhang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Evaluation of droplet evaporation models for the large eddy simulation of a turbulent lifted spray flame

    by Teng Zhang, Jinghua Li, Yingwen Yan, Zemin Tian

    1. The combustion of liquid fuels constitutes the fundamental energy conversion process in a wide range of modern propulsion and power generation systems, like aero-engines, liquid rocket engines, ...

  • Soot formation in turbulent non-premixed jet flames based on a flamelet-generated manifold with heat loss

    by Yating Jin, Teng Zhang, Zhonghua Gui, Jinghua Li, Yi Gao, Yingwen Yan

    This study presents a numerical simulation framework that integrates turbulence, combustion chemistry, and soot formation within OpenFOAM. A non-adiabatic, dual-scale flamelet-generated manifold model—hereafter dual-scale FGM (DS-FGM)—was developed and integrated with the method of moments with interpolative closure. The combined approach enables quantitative prediction of polycyclic aromatic hydrocarbons (PAHs) evolution, PAHs-to-soot conversion, and soot formation. To account for radiative heat loss and the disparate chemical time scales among species, a normalized enthalpy-loss parameter dH was introduced into the conventional FGM framework. Two progress variables were employed to describe separately the evolution of major species and PAHs, thereby improving the representation capability of PAHs formation, accumulation, and transport in the Flamelet database. The numerical method was validated against a laboratory-scale ethylene turbulent diffusion flame; the simulations reproduced the spatial distribution characteristics of soot evolution. Results show that the proposed soot formation modeling framework can reasonably capture the soot formation and evolution processes in typical turbulent non-premixed jet flames. Comparison with experimental data indicates satisfactory accuracy for the temperature and soot volume fraction distributions. The root-mean-square error and normalized peak error analyses were performed to further quantify the deviations in the overall distribution and peak prediction of the soot volume fraction. However, the soot volume fraction is slightly underpredicted in some regions. This discrepancy likely arises from a combination of factors, including biases in precursors formation and soot nucleation caused by simplified PAH growth pathways in the gas-phase PAHs mechanism, local temperature prediction deviations, and modeling errors in turbulence–chemistry–soot interactions.

  • Large Eddy Simulation of a Turbulent Polydisperse Spray Flow: A Comparative Study of Subgrid Scale Models and Droplet Injection Models

    by Teng Zhang, Jinghua Li, Yingwen Yan, Yuxin Fan

    This study performs an investigation of the effects of the subgrid-scale (SGS) and droplet injection models in the large eddy simulation (LES) of turbulent two-phase spray flows. Three LES SGS models (Smagorinsky, wall-adapting local eddy viscosity (WALE), and dynamic Smagorinsky) and two droplet injection models (cone nozzle injection and conditional droplet injection) are validated to the experimental measurements. For both gaseous and liquid phases, all SGS models provide comparable results, indicating that the current two-phase flow field does not exhibit a pronounced sensitivity to the LES SGS model. As for different droplet injection models and spray dispersion angles, minimal differences are observed in the prediction of the gaseous mean and root-mean-square (RMS) velocity profiles. However, for the result of liquid phase, CDIM (conditional droplet injection model) predictions of the droplet mean diameter and velocity are in better agreement with experiments, and less sensitive to spray dispersion angle settings. While the CNIM (cone nozzle injection model) prediction of droplet diameter is less accurate when increasing the dispersion angle. The study suggests that turbulent two-phase spray flows are more influenced by the spray boundary conditions rather than the LES SGS models.


  • Open Access

    A Performance Simulation Methodology for a Whole Turboshaft Engine Based on Throughflow Modelling

    by Shuo Zhang, Aotian Ma, Teng Zhang, Ning Ge, Xing Huang

    To accurately predict the matching relationships between the various components and the engine performance in the whole aero-engine environment, this study introduces a two-dimensional throughflow simulation method for the whole aero-engine. This method is based on individual throughflow solvers for the turbo-machinery and the combustor. It establishes a throughflow simulation model for the whole engine by integrating with the compressor-turbine co-operating equations and boundary conditions. The turbo-machinery throughflow solver employs a circumferentially averaged form of the time-dependent Navier–Stokes equations (N-S) as the governing equation. The combustor solver uses the Reynolds Average Navier–Stokes (RANS) method to solve flow and chemical reaction processes by constructing turbulence, combustion, and radiation models. The accuracy of the component solver is validated using Pratt and Whitney’s three-stage axial compressor (P&W3S1) and General Electric’s high-pressure turbine (GE-EEE HPT), and the predicted results are consistent with the experimental data. Finally, the developed throughflow method is applied to simulate the throttling characteristics of the WZ-X turboshaft engine. The results predicted by the throughflow program are consistent with the GasTurb calculations, including the trends of shaft power delivered, specific fuel consumption (SFC), inlet airflow, and total pressure ratio of the compressor. The developed method to perform throughflow simulation of the whole aero-engine eliminates the dependence on a general component map. It can quickly obtain the meridian flow field parameters and overall engine characteristics, which is expected to guide the design and modification of the engine in the future.


  • Open Access

    A Performance Simulation Methodology of Whole Turboshaft Engine Based on ThroughFlow Modelling

    by Shuo Zhang, Aotian Ma, Teng Zhang, Ning Ge, Xing Huang

    To accurately predict the matching relationships between the various components and the engine performance in the whole aero-engine environment, this study introduces a two-dimensional throughflow simulation method for the whole aero-engine. This method is based on individual throughflow solvers for the turbo-machinery and the combustor. It establishes a throughflow simulation model for the whole engine by integrating with the compressor-turbine co-operating equations and boundary conditions. The turbo-machinery throughflow solver employs a circumferentially averaged form of the time-dependent Navier-Stokes equations (N-S) as the governing equation. The combustor solver uses the Reynolds Average Navier-Stokes (RANS) method to solve flow and chemical reaction processes by constructing turbulence, combustion, and radiation models. The accuracy of the component solver is validated using Pratt & Whitney’s three-stage axial compressor (P&W3S1) and General Electric’s high-pressure turbine (GE-EEE HPT), and the predicted results are consistent with the experimental data. Finally, the developed throughflow method is applied to simulate the throttling characteristics of the WZ-X turboshaft engine. The results predicted by the throughflow program are consistent with the GasTurb calculations, including the trends of shaft power delivered, specific fuel consumption (SFC), inlet airflow, and total pressure ratio of the compressor. The developed method to perform throughflow simulation of the whole aero-engine eliminates the dependence on a general component map. It can quickly obtain the meridian flow field parameters and overall engine characteristics, which is expected to guide the design and modification of the engine in the future.


  • Open Access

    Multiscale modeling of liquid jet breakup in crossflow using an Eulerian/Lagrangian approach

    by Ping Zhang, Wei Li, Teng Zhang, Yingwen Yan, Jinghua Li, Hao Tang

    Liquid atomization is a very complex issue, involving multiple length and time scales over several orders of magnitude. To better understand the atomization characteristics of the main injection in a lean premix prevaporize (LPP) combustor, a volume of fluid (VOF)–particle conversion algorithm Lagrangian particle tracking (LPT) coupled approach was proposed to simultaneously reproduce the primary and secondary breakup processes. A VOF model with an adaptive mesh refinement strategy was used to resolve the liquid disintegration on a large scale. The small liquid structures qualified as droplets were transformed into discrete particles based on particle conversion criteria. Next, these particles were tracked using the LPT method to simulate the secondary breakup process. The proposed coupled method used in the Eulerian/Lagrangian framework was validated against liquid jet in crossflow experimental data. The numerical results achieved good agreement with the experimental data. Finally, the proposed method was used to predict the atomization characteristics of the main injection in an LPP combustor under various aerodynamic conditions. Qualitative and quantitative information about liquid deformation and spray characteristics were obtained, which varied depending on the aerodynamic parameters.