DVDmytro Verbitskiy

Dmytro Verbitskiy

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmytro Verbitskiy has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ANALYSIS OF THE STRUCTURE OF INTERFERENCE COATINGS FOR THE OPTIMIZATION OF THE PARAMETERS OF NARROWBAND OPTICAL FILTERS

    by Андрій Воронько, Denys Novikov, Dmytro Verbitskiy, Oleksandr Voloshyn, Oleksii Belkevych, Денис Новіков, Дмитро Вербіцький, Олексій Бєлькевич

    To monitor the parameters of semiconductor layers deposited from solid solutions of A3B5 compounds during the epitaxy, optical control methods are used. The choice of optical monitoring methods is determined by the reactor design, which requires non-contact, fast, and precise measuring of wafer surface parameters. During the growth of epitaxial layers, the deposition of semiconductor compounds causes changes in the optical parameters of the wafer surface. To ensure precise measurements, it is essential to monitor these parameters within a narrow spectral range. In electro-optical monitoring systems, narrowband interference filters are used to select the desired spectrum. However, this type of filters is sensitive to several factors, such as environmental conditions, aging of the coating, and the angle of incidence. As a result, the manufacturing of narrowband optical filters with stable and precisely controlled optical characteristics presents a complex challenge. This article analyzes the impact of various factors on the optical characteristics of interference coatings. Quantitative analysis of these shows that shift of the selected spectral band with central wavelength λmax can approach or even exceed the full width at half maximum (FWHM). These changes in the optical characteristics of narrowband filters lead to a decrease in the accuracy required for optical monitoring during epitaxial processes, which leads to inaccuracies in measurements. The results of this analysis will guide the optimization of thin-film structures used in narrowband optical filters. The study of the shift in the selected band also enables, within certain limits, controlled changes to λmax or the compensation of its shift its shift during regular factor variations. Ultimately, it enables to take these changes into account when designing electro-optical systems for monitoring the epitaxial growth of semiconductor heterostructures, which increases the accuracy and stability of optical measurements in the required accuracy range.

  • Properties of Low-Temperature GaAs Obtained by LPE Method for Terahertz Devices

    by Semen Krukovskyi, Mykola Vakiv, Yevhen Yashchyshyn, Vladyslav Arikov, Andriy Voronko, Denys Novikov, Dmytro Verbitskii, Oleksii Kryvets

    The paper presents the results of studying the peculiarities of the high-resistivity low-temperature gallium arsenide formed by the liquid-phase epitaxy (L

  • Open Access

    SPECIFICS OF DESIGNING AN INFRARED PYROMETER-REFLECTOMETER FOR SEMICONDUCTOR HETEROSTRUCTURE FABRICATION

    by Andriy Voronko, Denys Novikov, Dmytro Verbitskiy, Maksym Chmyr, Oleksandr Voloshyn, Oleksii Belkevych, Marharyta Holubets

    There are general technical requirements for all types of reactors for chemical vapour deposition technology using AIII- BV metalorganic compounds. Among them, it is worth highlighting the large temperature gradients that cause the origin of convection loops, which in turn, taking into account the high speed of the gas flow, lead to turbulence in the reactor instead of the expected laminar flow. It is also important to take into account the change in parameters of the wafer surface during the growth process and the need for signal separation between the useful signal from the wafer surface and the background signal from the wafer carrier, which rotates at fixed speed for uniform deposition of compounds. To obtain high-quality heterostructures with reproducible parameters, it is important to have a system of precise temperature control on the wafer surface directly in the deposition area, since the deposition process for many complex semiconductor devices (for example, laser diodes, LEDs, photodiodes, transistors on heterojunctions) is very sensitive to temperature changes. The method of optical pyrometry is a non-contact method that allows to precisely determine the temperature of the wafer surface and meets the technical requirements of CVD epitaxy growth reactors. This article is devoted to the analysis of the features of the development of optoelectronic systems for precise temperature measurement during epitaxial growth in order to determine the criteria for the selection or development of components of the optoelectronic system of the pyrometer-reflectometer. The main physical processes, electro-optical characteristics of Si photodiode, AlGaAs/GaAs LED and parameters of bandpass interference filters were investigated. Based on the analysis of the obtained research and measurement results, scientific recommendations have been developed. The recommendations aimed at the selection and optimization of the parameters of the components of the pyrometer-reflectometer (photodetectors, light emitting diodes, optical filters) in order to improve the accuracy and temperature stability of measurements in the pyrometer’s operation conditions, which take into account the compensation of emissivity change from the surface of the wafer.


  • Open Access

    Research on the Dynamic Range of Silicon Photodiodes for Optical Pyrometry Applications

    by Dmytro O. Verbitskyi, Андрій О. Воронько

    Оптична пірометрія є одним з основних безконтактних методів для прецизійного вимірювання температури напівпровідникових підкладок для технології газофазної епітаксії з металоорганічних сполук (ГФЕ МОС). Вимоги до фотоелементу пірометра обумовлені особливістю процесу. У пірометрі кремнієвий фотодіод функціонує в режимі, який характеризується невеликим значенням напруги зміщення, високою чутливістю до слабкого світлового випромінювання та низьким рівнем шумів. Основні температури, які використовуються в технології газофазної епітаксії, залежать від матеріалу напівпровідника, який вирощується, та від параметрів процесу. Зазвичай, температури процесу знаходяться в діапазоні від 500 до 1200 °C. В даній статті розглянуто кремнієвий p-n фотодіод, який використовується як чутливий елемент в пірометричній системі контролю. Вимогами до фотодетектора є достатній час наростання і спаду для роботи з модульованим світлом з частотою до 10 кГц, що обумовлено обертанням тримача пластин в реакторі, висока монохроматична ампер-ватна чутливість в області вимірювання і мінімальне значення темнового струму. Показано, що спектральна струмова чутливість кремнієвого фотодіода визначається коефіцієнтом відбиття випромінювання від поверхні Rλ і внутрішнім квантовим виходом ηλ, який визначається конструкцією переходу. Значення темнового струму і ампер-ватної спектральної чутливості фотодіоду залежать від конструктивно-технологічних факторів. Для досягнення мінімального значення темнового струму та максимальної спектральної чутливості в діапазоні понад 900 нм, для планарно-дифузійної технології необхідні високоякісні кремнієві пластини з великою дифузійною довжиною. Це призводить до підвищення спектральної чутливості та зменшення шумової складової генерації струму. В ході роботи були отримані фотодіоди, серед яких для подальших досліджень були відібрані ті, що мають найменше значенням темнового струму і максимальною ампер-ватною чутливістю на робочій довжині хвилі вимірювання. Дослідження показали, що температурний поріг для кремнієвого фотодіода з робочою довжиною хвилі 930 нм становить 450 °C. Аналітичні та емпіричні дослідження дозволяють покращити характеристики систем контролю температури для технології газофазної епітаксії. Також отримані результати сприяють розробці технології отримання фотоприймачів з покращеними характеристиками. У цьому випадку це дає змогу підвищити точність вимірювання температури поверхні пластин і контролю параметрів в процесі газофазної епітаксії, що в свою чергу призводить до підвищення ефективності самого процесу MOCVD.