Peter A. Parker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter A. Parker has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Devin Edward Burns
Advanced Measurement and Data Systems Branch, NASA Langley Research Center, Hampton, USA
3 shared publications - G. Geoffrey Vining
Virginia Tech
2 shared publications Kenneth G. Toro
Advanced Measurement Systems, NASA Langley Research Center, Hampton, VA, USA
2 shared publicationsBil Kleb
NASA Langley Research Center, Hampton, Virginia 23681
1 shared publication- Bradley Jones
JMP Division/SAS, Cary, North Carolina
1 shared publication Christine Anderson‐Cook
Los Alamos National Laboratory, Los Alamos, NM 87545, U.S.A.
1 shared publication
Latest Publications
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (24) , 40575-40580
Flowthrough Balance for Reaction Control Testing
Atmospheric entry vehicles undergo wind tunnel testing during development and the flight certification process. During testing, reaction control system (RCS) thrusters are simulated using high-pressure fluid to validate RCS design and enable developing controller algorithms. Traditionally, flowing high-pressure fluid through a six-component balance has been impractical using conventional manufacturing, and has limited force measurement to five components (no axial force). A new six-component flow-through balance enabled by additive manufacturing was developed, which is suited for RCS ground testing fluid pressures up to 13.8MPa (2000 psi). Multiple prototypes with compliant flow passages were designed and fabricated to enable axial force measurements. One selected design was fully fabricated, instrumented, and evaluated. Results confirmed finite element analysis (FEA) predictions of gage outputs, flow passage compliance, and successfully demonstrated the high-pressure flow-through concept.
- 6 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (24) , 40575-40580
Flowthrough Balance for Reaction Control Testing
Atmospheric entry vehicles undergo wind tunnel testing during development and the flight certification process. During testing, reaction control system (RCS) thrusters are simulated using high-pressure fluid to validate RCS design and enable developing controller algorithms. Traditionally, flowing high-pressure fluid through a six-component balance has been impractical using conventional manufacturing, and has limited force measurement to five components (no axial force). A new six-component flow-through balance enabled by additive manufacturing was developed, which is suited for RCS ground testing fluid pressures up to 13.8MPa (2000 psi). Multiple prototypes with compliant flow passages were designed and fabricated to enable axial force measurements. One selected design was fully fabricated, instrumented, and evaluated. Results confirmed finite element analysis (FEA) predictions of gage outputs, flow passage compliance, and successfully demonstrated the high-pressure flow-through concept.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (2) , 606-610
Titanium Wind Tunnel Balance Leveraging Additive Manufacturing
Titanium force transducers have among the highest strength–to–Young’s modulus ratios of common transducer materials. This can be leveraged to increase the sensitivity of the transducer relative to other materials or to increase the structural safety factor of the transducer for a given sensitivity. It is surprising then that no titanium wind tunnel balances have been reported in the literature or produced by NASA. With the increasing maturation of additive manufacturing technology, this work explores additively manufacturing a titanium wind tunnel balance. Additive manufacturing of the balance was completed in less than 1 week. Then, several secondary finishing and machining operations were performed to finalize the balance geometry, and it was strain gaged and calibrated. Calibration results confirm that the titanium balance has approximately 68% higher output compared to a steel balance of identical geometry and applied load. Based on the calibration results, hysteresis, pure error, and accuracy of the titanium balance are reported. These performance characteristics are comparable to conventionally manufactured state-of-the-art steel balances.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (2) , 606-610
Titanium Wind Tunnel Balance Leveraging Additive Manufacturing
Titanium force transducers have among the highest strength–to–Young’s modulus ratios of common transducer materials. This can be leveraged to increase the sensitivity of the transducer relative to other materials or to increase the structural safety factor of the transducer for a given sensitivity. It is surprising then that no titanium wind tunnel balances have been reported in the literature or produced by NASA. With the increasing maturation of additive manufacturing technology, this work explores additively manufacturing a titanium wind tunnel balance. Additive manufacturing of the balance was completed in less than 1 week. Then, several secondary finishing and machining operations were performed to finalize the balance geometry, and it was strain gaged and calibrated. Calibration results confirm that the titanium balance has approximately 68% higher output compared to a steel balance of identical geometry and applied load. Based on the calibration results, hysteresis, pure error, and accuracy of the titanium balance are reported. These performance characteristics are comparable to conventionally manufactured state-of-the-art steel balances.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (1) , 117-131
An Improved High-Capacity Balance Calibration Methodology
The objective of this research was to improve calibration efficiency for NASA Langley Research Center wind tunnel force measurement instruments (balances) that are rated at 31.14 kN and more. The current high-capacity balance calibration process consists of stacking weights in baskets, assembling hangers, knife edges, and bell cranks, and repeated leveling of the balance and the applied cable loads. New concepts for hardware and calibration execution procedures were designed featuring a hydraulic force application system and a precision applied load measurement system based on a platform balance design. Rather than concentrating on applying precise dead weight loads, the new approach relies on precise measurements using an external reference platform balance force measurement system. A complete design and analysis are presented here, including a solid CAD model for the platform balance. The structure was analyzed using finite element methods and a virtual calibration was conducted using a statistically based experimental design.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (1) , 117-131
An Improved High-Capacity Balance Calibration Methodology
The objective of this research was to improve calibration efficiency for NASA Langley Research Center wind tunnel force measurement instruments (balances) that are rated at 31.14 kN and more. The current high-capacity balance calibration process consists of stacking weights in baskets, assembling hangers, knife edges, and bell cranks, and repeated leveling of the balance and the applied cable loads. New concepts for hardware and calibration execution procedures were designed featuring a hydraulic force application system and a precision applied load measurement system based on a platform balance design. Rather than concentrating on applying precise dead weight loads, the new approach relies on precise measurements using an external reference platform balance force measurement system. A complete design and analysis are presented here, including a solid CAD model for the platform balance. The structure was analyzed using finite element methods and a virtual calibration was conducted using a statistically based experimental design.
- 1 November 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 59 (6) , 1926-1933
New Flow-Through Wind-Tunnel Balance for Retropropulsion Testing
Supersonic retropropulsion, or the use of retrorockets starting at supersonic conditions, is an enabling technology for large-scale human Mars lander vehicle concepts. A new flow-through balance was designed and fabricated to support an upcoming retropropulsion test campaign at the NASA Langley Research Center Unitary Plan Wind Tunnel. The balance employs membranes in place of bellows, which have historically been used, and passes the flow-through load-bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aerodynamicists a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.
- 1 November 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 59 (6) , 1926-1933
New Flow-Through Wind-Tunnel Balance for Retropropulsion Testing
Supersonic retropropulsion, or the use of retrorockets starting at supersonic conditions, is an enabling technology for large-scale human Mars lander vehicle concepts. A new flow-through balance was designed and fabricated to support an upcoming retropropulsion test campaign at the NASA Langley Research Center Unitary Plan Wind Tunnel. The balance employs membranes in place of bellows, which have historically been used, and passes the flow-through load-bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aerodynamicists a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.
- 28 March 2020
- Published by Taylor & Francis in Quality Engineering
- Vol. 32 (2) , 191-192
Discussion of “A novel approach to the analysis of spatial and functional data over complex domains”
(2020). Discussion of “A novel approach to the analysis of spatial and functional data over complex domains”. Quality Engineering: Vol. 32, No. 2, pp. 191-192.
- 28 March 2020
- Published by Taylor & Francis in Quality Engineering
- Vol. 32 (2) , 191-192
Discussion of “A novel approach to the analysis of spatial and functional data over complex domains”
(2020). Discussion of “A novel approach to the analysis of spatial and functional data over complex domains”. Quality Engineering: Vol. 32, No. 2, pp. 191-192.
- 29 July 2016
- Published by Taylor & Francis in Quality Engineering
- p. 00
Discussion of “Optimizing in a Complex World: A Statistician's Role in Decision Making”
- 29 July 2016
- Published by Taylor & Francis in Quality Engineering
- p. 00
Discussion of “Optimizing in a Complex World: A Statistician's Role in Decision Making”
- 2 January 2016
- Published by Taylor & Francis in Quality Engineering
- Vol. 28 (1) , 39-41
Discussion of “Space-filling designs for computer experiments: A review”
(2016). Discussion of “Space-filling designs for computer experiments: A review”. Quality Engineering: Vol. 28, Special Issue on the Third Stu Hunter Research Conference, pp. 39-41.
- 2 January 2016
- Published by Taylor & Francis in Quality Engineering
- Vol. 28 (1) , 39-41
Discussion of “Space-filling designs for computer experiments: A review”
(2016). Discussion of “Space-filling designs for computer experiments: A review”. Quality Engineering: Vol. 28, Special Issue on the Third Stu Hunter Research Conference, pp. 39-41.
- 11 December 2013
- Published by Taylor & Francis in Quality Engineering
- Vol. 26 (1) , 117-120
Discussion of “Reliability Meets Big Data: Opportunities and Challenges”
- 11 December 2013
- Published by Taylor & Francis in Quality Engineering
- Vol. 26 (1) , 117-120
Discussion of “Reliability Meets Big Data: Opportunities and Challenges”
- 26 March 2012
- Published by Taylor & Francis in Quality Engineering
- Vol. 24 (2) , 306-316
Statistical Engineering Perspective on Planetary Entry, Descent, and Landing Research
Statistical engineering emphasizes developing and leveraging statistical methods and tools to help identify and solve large, complex problems. Within NASA, these large, complex problems are known as the agency's “Grand Challenges.” Research in planetary entry, descent, and landing technologies is one of these challenges and is an expensive, resource-intensive endeavor that benefits from the rigorous approach of statistical engineering. This article highlights the contributions of statistical engineering to the Mars Science Laboratory mission and, more generally, planetary entry, descent, and landing research. For example, a new approach utilizing response surface methods was developed for characterizing a complex measurement system. In addition, we reflect on areas where early implementation of a statistical engineering approach can increase the overall impact of the research objectives.
- 26 March 2012
- Published by Taylor & Francis in Quality Engineering
- Vol. 24 (2) , 306-316
Statistical Engineering Perspective on Planetary Entry, Descent, and Landing Research
Statistical engineering emphasizes developing and leveraging statistical methods and tools to help identify and solve large, complex problems. Within NASA, these large, complex problems are known as the agency's “Grand Challenges.” Research in planetary entry, descent, and landing technologies is one of these challenges and is an expensive, resource-intensive endeavor that benefits from the rigorous approach of statistical engineering. This article highlights the contributions of statistical engineering to the Mars Science Laboratory mission and, more generally, planetary entry, descent, and landing research. For example, a new approach utilizing response surface methods was developed for characterizing a complex measurement system. In addition, we reflect on areas where early implementation of a statistical engineering approach can increase the overall impact of the research objectives.
- 26 March 2012
- Published by Taylor & Francis in Quality Engineering
- Vol. 24 (2) , 292-305
Aerospace Research through Statistical Engineering
The application of statistical engineering as described here is applied to fundamental research in support of hypersonic air breathing propulsion. An aerospace experiment that took place in a wind tunnel is the application of interest. One goal of the project was to accurately model the relationship between specific input and output parameters in the hypersonic combustion process within a controlled environment. Response surface methodology (RSM) was applied in a nontraditional manner to develop the response surface as the final deliverable rather than a tool to optimize a product or process.
- 26 March 2012
- Published by Taylor & Francis in Quality Engineering
- Vol. 24 (2) , 292-305
Aerospace Research through Statistical Engineering
The application of statistical engineering as described here is applied to fundamental research in support of hypersonic air breathing propulsion. An aerospace experiment that took place in a wind tunnel is the application of interest. One goal of the project was to accurately model the relationship between specific input and output parameters in the hypersonic combustion process within a controlled environment. Response surface methodology (RSM) was applied in a nontraditional manner to develop the response surface as the final deliverable rather than a tool to optimize a product or process.